(a) A four-pole three-phase induction motor operate at 50-Hz. It has the no-load speed of 2940 rpm and the full-load speed of 2860 rpm. (i) Calculate the motor speed. (ii) Calculate the motor no-load slip and the electrical frequency of the rotor. (ii) Calculate the motor full-load slip and the electrical frequency of the rotor. (iv) Determine the speed regulation of this motor.

(a) A four-pole three-phase induction motor operate at 50-Hz. It has the no-load speed of 2940 rpm and the full-load speed of 2860 rpm. (i) Calculate the motor speed. (ii) Calculate the motor no-load slip and the electrical frequency of the rotor. (ii) Calculate the motor full-load slip and the electrical frequency of the rotor. (iv) Determine the speed regulation of this motor.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Similar questions

L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no
7- A 6-pole, 50-Hz, 3-0 induction motor is running at 950 rpm and has rotor Cu loss of 6 kW. Its rotor input is......kW (a) 120 (b) 60 (c) 6.3 (d) 66 8- The number of slip rings on a squirrel cage induction motor is usually (a)Two (b) Three (c) Four (d) None
2. Describe the Torque-Slip characteristics of a three phase induction motor.
What are the options suits for a slip ring induction motor? (A) Slip ring induction motor has high starting torque (B) Slip ring Induction motor has a complicated construction (C) Slip ring induction motor has high efficciency (D) Slip ring induction motor has more copper loss O a. (A) and (B) O b. (A), (B) and (C) O c. (A) and (C) O d. (A), (B) and (D)
6- Which of the following supply is given to the rotor winding of 3-Phase Induction Motor: a) DC Supply b) AC Supply c) No Supply d) Pulsating Supply 7- 3-Phase Induction Motor will have Starting Torque and Starting Current a) High, High b) Low, Low. c) High, Low d) Low, High 8- Which of the following method is used for controlling the speed of an induction motor: a) Changing number of stator poles b) Supply voltage control c) Frequency control d) All the options are correct 9- Which of the following method cannot be used for starting of 3-Phase Squirrel Induction Motor: a) Star-Delta Starting b) Line resistor startling c) transformer Starter d) Rotor Resistance Starting 10- The rotor of a stepper motor has no: a) windings b) commutator c) brushes d) all of the above
(Qld) A three-phase 20-pole induction motor is rated at 800 V, 50 Hz. What is the synchronous speed of this machine if the voltage at its terminals is reduced to 400 V (a) 150 rpm, (b) 300 rpm, (c) 600 rpm, (d) 3000 rpm
An 8 pole, 50 Hz slip ring induction motor runs at a slip of 2.67% on full load. The rotor resistance per phase of the winding is 0.2 ohm. What external resistance per phase must be added in the rotor circuit so that the motor now runs ate a slip of 17.33% such that the torque remains same in both the cases. (Ans: 1.1 ohm)
a) The rotor of a 3 phase, 60HZ, 4 pole induction motor takes 120 KW at 3 Hz. Determine: 1- The rotor speed. 2- The rotor copper losses.
1.why the slip of induction motor is never zero, 2.what happens if the slip of induction motor is one, 3.what is the value of the slip for an induction motor at on load and full load
Explain torque speed/torque slip characteristics of 3 phase induction motor.
6- In a stepper motor, how is the speed of rotation determined? a) By the current supplied to the motor. b) By the magnitude of the voltage applied. c) By the load applied to the motor. d) By the frequency of the waveforms used. 7- A transformer core is laminated to a) reduce hysteresis loss b) reduce eddy current losses c) reduce copper losses d) reduce all above losses 8- An induction motor with 580 r.p.m. speed at 60 Hz will have a) 8 poles b) 6 poles c) 4 poles d) 2 poles 9- If any two phases for an induction motor are interchanged a) the motor will run in reverse direction b) the motor will run at reduced speed c) the motor will not run d) the motor will burn 10- No-Load speed of which of the following motor will be highest? a) Shunt motor b) Series motor c) Short-Shunt compound motor d) Long-Shunt compound motor
Design a DC motor circuit to drive A fan-type load with a torque equation equal to: TL=1.34×10−7ω2TL=1.34×10−7ω2 N.m The fan speed range is from 500 to 1200 rpm. To achieve the required operation, the armature voltage of the motor is adjusted by a single-phase, full-wave, ac/dc converter. The input voltage and frequency to the converter are 480 V (rms) and 50 Hz. choose the motor type, show the motor rating, αα range, Supply voltage, and frequency, and any required other information Modify the design to automatically adjust the voltage drive the load within the specified speed range. show the control variable, controller type, connection, and controller weights.