(a) A closed feedwater heater with U = 1986 W/m2•C uses condensing steam at T = 109•C for heating 38,548 kg/h of water (C, = 4186 J/kg °C) from 15.55°C to 101.6°C. What is the heating surface area in m? (b) After some fouling of the tubes, the exit temperature of feedwater becomes 97.7 C, find U

(a) A closed feedwater heater with U = 1986 W/m2•C uses condensing steam at T = 109•C for heating 38,548 kg/h of water (C, = 4186 J/kg °C) from 15.55°C to 101.6°C. What is the heating surface area in m? (b) After some fouling of the tubes, the exit temperature of feedwater becomes 97.7 C, find U

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
Super heated steam
An ammonia system with a 158-kW evaporator operating at -1°C and a 35-kW evaporator operatingat -40°C uses flash gas removal and intercooling. The condensing temperature is 32°C. Thearrangement is as shown. How many kilograms per minute of ammonia are compressed by the high-pressure compressor?
i meed help to solve this thermo question
Pls answer with complete solution.
helpp
In the condenser of the power plant, Ammonia is isobarically condensed to saturated liquid state with 615.2kPa and x = 0.9, the mass flow rate is 4 t/h. The heat rejected from the condensing ammonia is added to heat water, which is heated from 277K to 281K. What is the mass flow rate of water in t/h. Also sketch the T-s and P-v diagrams.
The condenser of a steam power plant has a total surface area of 45m^2 and an overall heat transfer coefficient of 2100Watts/m^2-K. Saturated steam from the turbine enters this condenser at 30C and leaves as saturated liquid at the same temperature. Cooling water enters the condenser at 14C and leaves at 22C. A. Draw the figure, sketch the t-L diagram, then, compute the LMTD of the cross-flow heat exchanger in Kelvin. B. How much heat is transferred by the condenser in MW? C. How much steam passes through the condenser in kg/s? D. How much cooling water is supplied to the condenser in kg/s.
B// What are the methods of draught in cooling towers. Demonstrate them with drawings. What is the relationship between the cooling tower and condenser. Q4IIA// Prove for the condenser: %3D + Cow (Tw2-Tw1) when the temperature of cooling water outlet and inlet is equal to saturation temperature of steam and the condensate leaving the condenser respectively; also, the inlet of condenser is dry steam with unity latent heat. Twi 1
Problem: An ammonia refrigerating system shown in the figure is composed of three evaporators and arranged with multiple expansion valves and intercoolers. The load and operating temperature of each evaporator are shown in the table below: condenser evaporator 3 compressor 3 intercooler 2 evaporator 2 compressor 2 Infercooler 2 liquid evaporator 1 compressor 1 Evaporator Load, tons Evaporator Temperature, °C 1 30 - 30 20 - 20 15 - 10 Condensing pressure is 1200 kPa. Refrigerant vapor exits evaporator no. 1 with a 10 - degree superheat. Saturated conditions exist at the exits of the evaporator no. 2 and evaporator no. 3. Liquid refrigerant leaves the condenser at 28°C. Determine a. the mass flow rate in evaporator 1 kg/s b. the mass flow rate in evaporator 2 kg/s c. the mass flow rate in evaporator 3 kg/s
5.) By traveling through a bass tube, 2.5 cm O.D. and 2.2 cm I.D., which is surrounded by steam at 55 kPa and 90% quality, 9.4 kg/s of water is heated from 15oC to 60oC. Assume the inside unit convective coefficient is 2000 W/m2-K, and the outside unit convective coefficient is 7950 W/m2-K. Determine (a) the length of tube required; (b) the steam supply in kg/h if no subcooling occurs.
Q12 A refrigerator is used to remove a heat from a food at a rate of 532.6 kW and required a compressor power of 219 kW, what is the heat added to the surrounding (kW)? (D) 563.7 (A) 243.2 (B) 313.6 (C) 751.6 (E) None of them far infore?