А (а) (b) A (с)

Q: AR Зм J 4 m w= 15 k/m Эм

A:

Q: Determine the horizontal and vertical components of reaction at the pin A and the re the rocker B on…

A:

Q: B fm fm Draw the influence line for the beam Use Müller-Breslau's Method 1 Reaction at A 2 Reaction…

A:

Q: A 2. Find the reactions at Pin A and roller B. The beam is 18 feet long, and the two forces are…

A:

Q: The Frame is hinged at rigid supports in A & E. Find the components of the reaction at A and E and…

A: To find support reaction and force in member BC,BD

Q: Draw the influence line for vertical reaction t support B, shear at C and the moment at point D of…

A: We have to find out the ILD for vertical reaction at B, ILD for shear at C and ILD for moment at D.…

Q: Draw the influence lines for members DI and IJ of the truss depicted in the figure below assuming…

A:

Q: 3. Construct and draw influence lines for the reactions at(ACand E, the shear at D the moment at D,…

A:

Q: The 60 mm diameter shaft shown below is steel (G=83 GPa). 800 Nm 1000 Nm 1200 Nm 60 mmo 1.5 m 2 m 3…

A: 3a. Which of the following gives the reaction at fixed end. 3b. Which of the following givesthe…

Q: 3. For the system shown, a. Determine the equivalent force-couple system at the base at C. Express…

A: Determine the equivalent forces-

Q: Construct the influence lines of each truss member. H 4 m В E 6@3 m = 18 m

A: An influence line for an obtained member, like reaction, axial force, shear force, or bending…

Q: 3 m A B 3 @ 4 m = 12 m LOAD W(LL) P(LL) SET 1 (1,2,3,4,5) SET 2 (6,7,8,9,0) 20 90 15 110 Draw the…

A:

Q: The designed to withstand a uniformly distributed live load of 60 kN/m, a dead load of 20 kN/m, and…

A:

Q: E A В C -8 m- -8 m- -5 m- -5 m-

A:

Q: 05. Replace the forces acting on the frame shown by a single resultant force-couple, with the force…

A: For calculating the resultant force, first determine sum of forces along y and x axis. Then find…

Q: For the frame provided, determine the following: A. The vertical component of the reaction at pin B,…

A:

Q: Determine the reactions at B, C, and the maximum force F if the reaction at A is 175 kN. Note that…

A: To find Reaction at B &C  Maximum force F

Q: 20KN/m D 4m kN/m | 6m B 5m

A:

Q: Q2. Draw the influence lines for the vertical reactions at supports A and B and moment at A of the…

A: ILD : Influence line diagram ILD represents variation of stress function when a unit concentrated…

Q: The Frame is hinged at rigid supports in A & E. Find the components of the Reaction at A and E and…

A: To find support reaction

Q: 1 kN/m, a live load of 2 kN/m, and a concentrated live load of 52 kN. Determine the following:…

A:

Q: Solve for the Reactions at Roller A and Pin B

A: It is required to determine the support reactions.

Q: SHOW THE FREE BODY DIAGRAM. SOLVE FOR THE VERTICAL REACTION AT A AND D AND MOMENT REACTION AT A.

A:

Q: sieve analysis what's the meaning or gonna happen if the So is zero

A: A sieve test is generally called as gradation test, is one of the most important and widely used…

Q: IV. Determine the indicated reactions. The upper beam is supported by a roller at C which separates…

A: Finding out reaction.

Q: Solve the reactions at the supports. Use SUPERPOSTION 51kN 2m 2m 102kN 81.6kN/m 3m 2m

A: Given beam :- Here, we have to find the reaction At A, B , C In method of superpostition , we find…

Q: Construct the influence line for the shear at point C of the am: 4 m 10 m

A: To draw ILD for shear at point C

Q: #2 Draw the influence lines for (a) the vertical reaction at A, (b) the shear at C, and (c) the…

A: Total length = 5+4+7+3 = 19

Q: 2. Construct and draw the influence lines for the reactions Rg and R, shears Vc and Vco, and the…

A: We have to draw the influence lines

Q: II. If the beam carries a moving uniform load of 1.19kN/m and concentrated moving load of SN kN as…

A:

Q: 10 N.m A 6m

A: To determine: Magnitude of reaction at B.

Q: Determine the moment reaction at A of the given indeterminate frame below. -15 ft 15 ft В 15 ft 4…

A:

Q: Determine the reaction at A and the force in each member of the left half of the truss.

A:

Q: Determine the horizontal and vertical components of reaction at the supports A and B. 20kN/m

A:

Q: 3. Loaded as shown, the beam rest in the incined smooth surface at A and supported by a hinge at B.…

A: To Find :- Support reactions at A & B.

Q: Determine the moment at A in kN-m

A: To find moment about point A

Influence Lines

The graphs that show the variation of a function at a specific point on a beam or truss due to a unit load placed at any point along the structure are known as influence lines in engineering. Some common functions that are studied with influence lines are shear, moment, and deflection. In designing beams and trusses, it is important to use influence lines in structures where loads would move along their span such as bridges, crane rails, conveyor belts, floor girders, etc. The influence lines help to study where a load will create the maximum effect for any of the functions.