A₁ A₂ Ay Ag +5 V 411 MUX EN 0 G Figure Q2(a) 1. Figure Q2(a) shows a multiplexer 74LS151 (8 line-to-1 line multiplexer). (i) Analyse and built a truth table for this circuit. 2. From your answer in part Q2(a)(i), write a boolean expression for output, Y.
Q: 8.a. A grounded conductor is a conductor that has been _______ grounded. A. electronically B.…
A: 8.a. A grounded conductor is a conductor that has been intentionally grounded. It is used to carry…
Q: draw single line diagram of 33kv substation with explanation and not copied from anywhere
A: Single-Line Diagram or SLD A single-line diagram (SLD) is the simplest of the diagrams used to…
Q: Q4 The control system of an engine has an open-loop transfer function as follows; G(s) (a) (b) (c)…
A: "According to the Company's policy we will solve the first three parts". The control system of an…
Q: Consider an NMOS transistor fabricated in a 0.18-um process with = 0.18 um and W=2 um. The process…
A: In N-MOS transistor, at the edge of saturation: VDS=VGS-VTH…
Q: 1) write down the factors considered for selection of conductor for overhead LT distribution line.
A: We have to write the factors considered for selection of conductor for overhead LT(Line…
Q: Problem 2 Solve for iz for all values of t. 1=0 2 A -⁄²=; +1= C vom 1H 352
A:
Q: Q.7 a) Ring and number the junctions of component in the below circuit. R1 R2 R4 Input Output Q4 R3…
A: The given circuit diagram is shown below:
Q: In photoclectric effect, the number of photoclectrons emitted is proportional to A- intensity of…
A: Photoelectric effect : When a material absorbs electromagnetic radiation, a phenomenon known as the…
Q: 1) One theory about charging insulators is called adhesion. Look this up and explain (in about 3-4…
A: Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: Design a wide band pass filter with f = 500 Hz and f = 2 kHz, and a pass band gain = 5 for both…
A:
Q: A pulse code modulated system has 8 bits per sample. What is the number of levels present in the…
A: When a signal is modulated into a binary signal in accordance to the message signal, then it is…
Q: Determine the magnitude of force per 1.1 m length of a pair of conductors of a direct current line…
A:
Q: 10. a) A1: c) A3: + 12V 아 11. a) A1: c) V2: c) RT: 최다 + 12V A1 A3 A1 R1=32 ww M R2=3Q V1 10 302 b)…
A: Note current flowing in series circuit remain same but voltage varies based on a circuit element…
Q: 1.The logic OR function when expressed in algebraic terms is analogous to the ? 2.A 4 input NOR…
A:
Q: A series RLC circuit has R= 2000, L = 0.1 H, and a capacitor C = 10 uF. If a 200 V dc source is…
A:
Q: A capacitor in an LC oscillator has a maximum potential difference of 15V and a maximum energy of…
A: Given data, The potential difference is 15V, The maximum energy is360μJ, The instant energy in the…
Q: balanced and delta connected. D
A: Given- Phase Voltage- VRY=220∠0° VoltsVYB=220∠-120° VoltsVBR=220∠-240° Volts Line current- IR=10∠0°…
Q: 14.a. Section 250.94 requires that an IBT be accessible for inspection and termination and have the…
A: 14.a. IBT stands for Intersystem Bonding Terminal. According to NEC Section 250.94 (B) An IBT be…
Q: Assume that the two magnets shown below are sufficiently separated that their forces do not…
A: When the same type of pole is close to each other than magnet experience a repulsive force When the…
Q: Consider the RC circuit shown in figure. Find the following: (a) The governing differential equation…
A: Given data,
Q: V₂ = -2 V, IDSS = 1.65 mA for the circuit in Fig. It is desired to bias the circuit at ID = 0.8 mA,…
A:
Q: What are the basic logic gates in the MOS logic family? 1. NOR & NAND 2. AND & OR
A: In this case, the basic logic gates corresponding to the MOS logic family is to be determined.
Q: explain and write the advantage and disadvantage of the following wiring system i. cleated system…
A:
Q: At a certain frequency, the output voltage of a filter is 6 V and the input is 12 V. The voltage…
A: Given: In a filter V0=6 VVin=12 V
Q: what is kvl and kcl in circuit theory ?
A: The electrical circuit consists of various active and passive elements and The circuit calculations…
Q: Write down the specification of motor and stator for (a) DC motor (b) AC motor
A: DC Motor:- A group of rotating electric motors that use direct current (DC) electricity to create…
Q: 80. A series circuit with one branch of R= 60 and a single unknown element in the other branch has…
A: Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: A majority logic function is a Boolean function that is equal to 1 if the majority of the variables…
A: The truth table can be obtained by counting the number of one's in the input if the number of one's…
Q: Q2 (a) Explain, using phasor diagrams, what happens to a synchronous motor as its load is varied.
A:
Q: + 20 V – 20 V + τό 10 ΚΩ SV 1 ΚΩ • 2.2 ΚΩ 7V· + • 2.2 kΩ
A: please refer the attached images for the complete answer...
Q: An electric utility company runs two 100 m copper wires from the street mains up to a customer's…
A: we have to calculate voltage drop.
Q: 80. A series circuit with one branch of R = 60 and a single unknown element in the other branch has…
A: Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: For the circuit Figure Q1(b), assume the circuit is in a steady state at t = 0¯ before the switch is…
A:
Q: 1.-(60) For the given circuit find: a) Vo (s). 6) Find the values of R's and és frequency response…
A: There can be different solutions for the component values based on what we assume every combination…
Q: An alternator stator winding protected by a percentage differential relay is shown in Fig. 1.12.8…
A:
Q: (a) (b) Name and describe the features of the FIVE (5) types of generators. All generators are…
A: Given: (a) Types of generators. (b) Potential prime mover of DC generator.
Q: what is protective relaying? what is Time & Setting Multiplier ?
A: What is protective relaying? A protection relays is a switching equipment which detect faults and…
Q: (II) Suppose that you have a 9.0-V battery and wish to applya voltage of only 3.5 V. Given an…
A: Given: A 9-V battery is present. Unlimited supply of 1 Ω resistors. Required: A 3.5 Volt output is…
Q: 1 μF C₁ 100μF www www.l R₁ 56 k Voc +10 V Ⓡ R₂ 12 k Rc 2.2 k 2N3904 Vout HE 1 μF RE 10 ΚΩ beta = 250
A:
Q: i(t) below wi R1 C1 ur.
A: j
Q: The denominator of the transfer function for a LPF is s² + s + 25. a) Find On, and Q. b) Is the…
A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…
Q: draw single line diagram of 11 kv substation with explanation and not copied from anywhere
A: 11 kV substation Important function of substation is to collect energy transmitted at high voltage…
Q: A pulse code modulated system has 8 bits per sample. What is the number of levels present in the…
A: Given: The number of bits transmitted per sample for the pulse code modulated system is 8. The…
Q: Q3 (a) (b) (c) Describe types of DC motors with description and its equivalent circuit. Illustrate…
A: TYPES OF DC MOTOR Separately Excited DC Motor Since name implies, in separately excited DC motors,…
Q: A current of 10 A flows through a non-inductive resistance in series with a choking coil when…
A:
Q: PMMC instrument has a coil of dimensions 10 mm x 8 mm. The flux density in the air gap is 0.15…
A: It is given that: A=10mm×8mm=800×10-6m2B=0.15 Wbm2N=100I=5 mAK=0.2×10-6 Nmdegree
Q: (c) A transmission line, modelled through a series reactance X = 0.4 p.u., supplies an electrical…
A:
Q: 64. A 50 Hz, 11 kV, 3-phase alternator with earthed neutral has a reactance of 5 ohms per phase and…
A: Given, A 50 Hz, 11 kV, 3-phase alternator with earthed neutral has Reactance = 5 ohms per phase The…
Q: Implement a full adder with two 4 × 1 multiplexers.
A: Implementation of Full adder with two 4:1 Multiplexers is explained below: Multiplexer : Multiplexer…
Q: In an ideal op-amp, which is not true?
A: The correct option along with the explanation is provided in the following section.
Step by step
Solved in 3 steps with 3 images
- Design a combinational circuit with the four inputs A,B.C, and D, and three outputs X, Y, and Z. When the binary input is odd number, the binary output is one lesser than the input. When the binary input is even number the binary output is one greate than the input. Implement the function using multiplexers with minimal input and select line.USE DIGITAL LOGIC AND DESIGN Part 1: In Figure_4; we have 4-bit Comparator using 2-bit Comparators block. You have to satisfy given condition by applying all data on figure 4. At the end, given condition should produce HIGH output and other two should be LOW. A3 A2 A1 A0 = 1101 and B3 B2 B1 B0 = 1110 Figure_4 Part 2: The serial data-input waveform (Data in) and data-select inputs (S0 and S1) are shown in Figure_5. Determine the data-output waveforms from D0 through D3. Figure_5 Part 3: Decoder can be useful when we have to decode some specific numbers from their equivalent code. Figure 6 has a concept of 3 to 8 line decoder from which you have to generate output waveform from D0 to D7 with proper relationship to input. Figure_6 Part 4: The data-input and…Logic Design courses / EE200SP21 / General / Mid Term Examination Part II (Subjecti Compute the minimal products of sum and minimal sum of products expressions for following KMAP. Show your groupings on KMAP АВ CD 1 1 1 1 0. Instructions: You have to solve the answer by hand on paper, scan/take photo and upload it as a single file. Local Disk (D:) Mid Term Examinat.
- H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem LateefDesign the interfacing circuit shown below and write a program to display single digit (between 0 and 9) prime numbers followed by even numbers, the next odd numbers and repeats in 7-segment displays and its equivalent 8-bit binary value in LEDS. a) When displaying Prime numbers, the first 7-segment display must show "P" and the second 7-segment display must show prime numbers one by one b) When displaying Even numbers, the first 7-segment display must show "E" and the second 7-segment display must show even numbers one by one c) When displaying Odd numbers, the first 7-segment display must show "O" and the second 7-segment display must show even numbers one by oneanswere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.
- (c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).Excess-3 code is significant for arithmetic operations as it overcomes shortcoming encountered while using 8421 BCD code to add two decimal digits whose sum exceeds 9. Excess-3 arithmetic uses different algorithm than normal non-biased BCD or binary positional number system. An electronics company has hired your services to design a code converter that converts Binary Coded Decimal (BCD) code for it. Design the converter.Which function performs the following operation? Give the assembly instruction and show your work. Before A= 11011011, CF=1 After A= 10111101, CF=1
- 3-) Analyze the circuits below and write the Boolean equation for each Part. Simplify the equation using Boolean algebra and determine if they function as an XOR, XNOR or neither. A): Dor B): XD XD . D1. Gray code to Binary converter: Gray code is one of the codes used in digital systems. It has the advantage over binary numbers that only one bit in the code word changes when going from one number to the next. (See Table 1). Design a combinational circuit with 4 inputs and 4 outputs that converts a four- bit gray code number into an equivalent four-bit Binary number. Use Karnaugh map technique for simplification. Use LogicWorks for pre-lab demonstrations. Select the library "7400dev.clf* in the Parts Palette and then select the XOR chip 74-86. This would give you a set of 4 XOR's as shown in Fig. 1, just like the hardware chip 74-86. You could use as many as needed from these XOR gates in your design. Get back to ALL LIBRARIES and select switches for the inputs and Binary Probes as indicators of the outputs. Verify your design in the pre-Lab. During the Lab construct the circuit and verify its operations.Design a logic circuit for decoder that accepts 3-bit input and displays alphabet “048” at the seven- segment as illustrated at Figure 1 (a). The input-output mapping shown in Table 1 (a). Refer Figure 1(b) and Figure 1(c) for seven-segment display format showing arrangements of segments using common anode connection. Show each steps clearly to produce the expressions and required design. [Rekabentuk litar logik untuk penyahkod yang menerima input 3-bit dan paparkan abjad "048" di tujuh-segmen seperti digambarkan pada Rajah 1(a). Pemetaan masukan-keluaran ditunjukkan dalam Jadual 1(a). Rujuk Rajah 1(b) and Rajah 1(c) untuk format paparan tujuh-segmen yang menunjukkan susunan segmen menngunakan sambungan 'common anode'. Tunjukkan setiap langkah dengan jelas untuk menghasilkan ungkapan dan reka bentuk yang dikehendaki.] Xs X6 X7 DECODER Figure 1(a) [Rajah 1(a)] a b с d e f g a 80123456789 Figure 1(c) [Rajah 1(c)] g Figure 1 (b) [Rajah 1(b)] b с DP