A 8 pole wave wound shunt generator delivers 185A at a terminal voltage of 240V. Ra and Rsh are 0.052 and 602 respectively. Neglecting brush drop, determine (i) armature current (ii) current per parallel path (iii) generated voltage and (iv) Power developed. armature current current per parallel path generated voltage Power developed

A 8 pole wave wound shunt generator delivers 185A at a terminal voltage of 240V. Ra and Rsh are 0.052 and 602 respectively. Neglecting brush drop, determine (i) armature current (ii) current per parallel path (iii) generated voltage and (iv) Power developed. armature current current per parallel path generated voltage Power developed

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 6 pole, wave wound DC shunt generator has a useful total flux of 420 mWb. The armature winding consists of 220 turns each of 0.004 2 resistance, when running at 900 RPM the armature current is 50 A. If the armature winding reconnected as lap calculate the terminal voltage in case of wave and lap given that the field circuit and the speed are kept same.
A 10 pole wave wound shunt generator delivers 178 A at a terminal voltage of 236 V. Ra and Rsh are 0.035 Q and 44 Q respectively. Neglecting brush drop, determine the armature current and generated voltage. Armature Current Generated Voltage
DC generators
A 12-kW, 250-V dc. shunt generator has armature and field resistances of 0.68 ohm and 120 ohm. respectively. Determine the total armature power developed in generator.
An 145-pole d.c. shunt generator with wave wound armature having 455 conductors, has to supply a load of 120 lamps each of 145W at 230 v. The flux per pole is 14 mWb and Ra = 1.8 ohms, Rsh355ohms. What will be the %3D load current and e.m.f generated . Consider brush drop of 1v/brush. Load Current Generated EMF
A 220 V , 60 Hz , supply is connected to 200 – turn armature winding of reluctance 1.7x105 At / Wb . Find the magnetizing reactance , the rms values of the ( magneto – motive force , exciting and armature currents , magnetic flux ) , and the inductance Draw the phasor diagram of the circuit .
A six-pole, 30-slot dc commutator generator has a lap wound Armature winding. The armature constant, Ka is 9.55.The generator is operated with a separately excited field such that the field flux per pole is 0.04 weber/pole. The generator is driven at a speed of 3000 rpm. The no load armature voltage is 418.9 V. The above generator is now operated as a motor. The flux is 0.04 weber/pole. It is desired to supply a load requiring a Torque of 50 n–m at 4000 rpm. Armature circuit resistance is 0.075 ohm. Calculate (a) the back emf, (b) the required armature current and voltage to supply this load.
With the aid of diagrams describe the basic topology of a wound field 3 phase synchronous generator and outline the relationship between the excitation voltage and rotor current. Q2 (a) (b) Outline with the aid of a suitable diagram the necessary power conversion stages required to interface a small permanent magnet (PM) generator to a stand alone DC system. A star connected 3 phase wound field synchronous generator with a synchronous reactance of 20 N is connected to a 6.6 kV (phase voltage) grid and supplies 1.5 MW at 0.95 lagging power factor at its terminals. Calculate the phase current and resultant voltage across the synchronous reactance (Vxs), and from a scaled phasor diagram graphically determine the required excitation voltage (Eph) and load angle (8). (c) The load is now increased to 3 MW with the Excitation Voltage kept constant. Using the phasor diagram drawn in part (c) graphically determine the resultant phase current, power factor and load angle. (d)
short shunt compound generator delivers a load current of 10A at 200V and has a shunt field resistance 200 ohms. The shunt field current of 2A. Then armature delivers a current of a.10A b.8A c.11A d.12A
Choose True (V) or false( x) for the following : 4) Reluctance is a measure of "opposition" the magnetic circuit offers to the flux. 5) The rated output power (transformer rating) can be used to determine the turns ratio of the transformer. 6) With the increase in speed of a series DC motor, Both back emf as well as line current increase. 7) When an induction motor is stationary, the stator and rotor windings form the equivalent of a transformer. 8) Increasing the load current for DC Self-excited generator Shunt-Wound Generator will increase the terminal voltage. 9) In lap windings there are as many paths in parallel and used to produce high current, low voltage output. 10) In 3-pahse induction motor, if the rotor speed increases, the rate at which the rotating magnetic field cuts the rotor bars is increasing.
Two DC generators, each with armature resistance of 0.02 ohm and fieldresistance of 50 ohms run in parallel and supply a total current of 1000 amperesto the load circuit. If their emfs are 270 V and 265 V, their bus bar voltagewill be. [Ans. 267.5 V]
Q/ dc shunt generator 4 pole with 500 condcutor , wave running at speed 1000 r.p.m the resistance of armature and field are 0.02 , 55 ohm and delivering load 43.12kwatt at terminal voltage 220 volt, the iron losses is 750 watt 1-Torque developed by the prime mover .........and The torque developed by the armature ........... when running at 1000 r.p.m * 2-The load current ,,,,,,,,,,,,when the speed drops to 800 r.p.m. if If is unchanged ? * 3-Output of the prime motor…….kwatt * 4-Mechanical , electrical and overall efficiency …….. * 5-Flux per pole is......... wb *