A 8-meter-high retaining wall, with a perpendicular back, retains the soil with a unit weight of 17.17 kN/m3. The cohesion and the internal friction angle of the backfill were measured as 13 kPa and 20°, respectively. Assume that there is no friction on the wall and the surface of the backfill is horizontal. Calculate the expected active force on the wall and the position of this force.

A 8-meter-high retaining wall, with a perpendicular back, retains the soil with a unit weight of 17.17 kN/m3. The cohesion and the internal friction angle of the backfill were measured as 13 kPa and 20°, respectively. Assume that there is no friction on the wall and the surface of the backfill is horizontal. Calculate the expected active force on the wall and the position of this force.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter14: Lateral Earth Pressure: Curved Failure Surface

Section: Chapter Questions

Problem 14.4P

See similar textbooks

Similar questions

A 6m retaining wall is supporting a soil with the following properties:Unit weight = 16 KN/cu.mAngle of internal friction = 25ºCohesion = 14 Kpaa. Assuming no tensile cracks occurs in the soil; determine its normal pressure acting at the back of the wall.b. If tensile crack occurs in the soil, calculate its active pressure acting on the wall.c. Find the location of tensile crack measured from the surface of horizontal backfill.
A retaining wall supports a horizontal backfill that is composed of two types of soil. The first layer is 4.47m high. It has a unit weight of 16.92kN/m3. The second layer is 5.76m and has a unit weight of18.51 kn/m3. If the angle of friction for both layers is 38 degrees, determine the total active force (kN) acting on the retaining wall per unit. Use stored value. Asnwer on 5 decimal places.
A retaining wall supports a horizontal backfill that is composed of two types of soil. The first layer is 4.74 meters high. It has a unit weight of 17.25 kN/m3. The second layer is 6.6 meters and has a unit weight of 18.4 kN/m3. If the angle of friction for both layers is 32°, determine the total active force (kN) acting on the retaining wall per unit width. Use stored value. Answer in 5 decimal places.
Considering that the horizontal thrust from the back of a 5.5 m wide brick wall to the 1 m deep part of the wall is H = 55 kN a) Find the greatest stress in the base when b = 2 m.b) Find the width b so that there is a shrinkage zone at the base.(Note: unit weight of brick wall ỿ = 24 kN / m3 ) Answer: ϭmax=0,30 Mpa, b=2,23 m
13.22 Consider the retaining wall shown in Figure 13.38. The height of the wall is 9.75m. and the unit weight of the sand backfill is 18.7kN/m3. Using Coulomb's equation, calculate the active force, Pa, on the wall for the following values of the angle of wall friction. Also, comment on the direction and location of the resultant.
An 8 m tall retaining wall holds cohesionless sand with a density and angle of internal friction of 1.85 Mg/m3 and 33°, respectively. If the surface of the backfill slopes upwards at 86° to the vertical, Use Rankine’s conditions to find the force per unit length of the wall and its location for (a) Active State (b) Passive State Please draw the pressure diagram neatly for both cases
A cantilever retaining wall supports 2 layers of soil and surcharge as shown below. The layers have these properties: Layer 1: 1.8m thick. γ = 17.4 kN/m3 and ϕ = 22 degrees Layer 2: 4.2m thick. γsat = 18.1 kN/m3 and ϕ = 30 degrees The angle of friction between the base and soil is 42 degrees. Unit weight of concrete is 23.6 kN/m3 What is the design moment (kNm / m) at the bottom of the stem? None of the choices 819.98 478.88 363.00 299.30 Please answer this asap. For upvote. Thank you very much
Assume that a frictionless retaining wall 15 ft high having a vertical backface supports a sandy soil with a unit weight of 118 pcf and an angle of internal friction of 34°. The soil backfill is level. Calculate the difference in the lateral force imposed onto the wall (per foot of wall length) when the at-rest lateral pressure condition applies compared to when the active lateral pressure condition applies (express the difference as a percentage increase related to the active pressure condition).
You are working for a consulting firm that has been asked to evaluate the factor of safety of the wall shown in the figure supported by a well-degraded sand. The resultant load behind the concrete wall acts at the one third point. Dw 1m 1.5 m 24 kN/m³ y = 20 kN/m³ 26.5 kN/m 24° = 34° n = 0.4 3 m (a) Determine the factor of safety if Dw − D > 1.5B. Ignore the lateral passive resistance due to the soil in front of the wall. (b) Determine the factor of safety if the ground water table rises to 0.5 m below the base of the wall. Discuss the significance of your observations.
Determine the stability of the cantilever gravity retaining wall shown in figure below. The existing soil is a clay and the backfill is a coarse-grained soil. The base of the wall will rest on a 50-mm-thick, compacted layer of the backfill. The interface friction between the base and the compacted layer of backfill is 25.0°. Groundwater level is 8 m below the base. 1.0 m Batter 1:20 0.4 m 1.8 m 9, = 20 kPa 8⁰ Ysat = 18 kN/m³ cs = 25° 8 = 15⁰ Backfill Drainage blanket Y = 23.5 kN/m³ 3 m Existing soil 6.1 m 0.9 mi Ysat = 19 kN/m³ = 35° % = 25°
A smooth unyielding wall retains a normally consolidated clay with no lateral movement of soil, that is at rest condition is assumed. a) Compute the coefficient of earth pressure at rest if the clay has a plasticity index of 7.8%. (Answer: 0.455) b) Compute the location of the resultant force. (Answer: 19.81 kN) c) Compute the total lateral force acting on the wall. (Answer: 1.20)
1. A retaining wall moved outward by a lateral strain of 0.08% caused by an additional 0.7kPa compressive stress along the vertical on a soil element located 3m below the ground surface. Assuming that the soil is linear, isotropic, and elastic, with E=10MPA and v=0.3. Calculate the change in lateral stress and the change in vertical strain on the soil element.