A 6-mm-diameter electrical transmission line is exposed to windy air. Determine the drag force exerted on a 160-m-long section of the wire during a windy day when the air is at 1 atm and 15°C and the wind is blowing across the transmission line at 65 km/h.

A 6-mm-diameter electrical transmission line is exposed to windy air. Determine the drag force exerted on a 160-m-long section of the wire during a windy day when the air is at 1 atm and 15°C and the wind is blowing across the transmission line at 65 km/h.

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter20: The First Law Of Thermodynamics

Section: Chapter Questions

Problem 20.15OQ

See similar textbooks

Similar questions

A 2.1-m-long, 0.2-cm-diameter electrical wire extends across a room that is maintained at 20°C. Heat is generated in the wire as a result of resistance heating, and the surface temperature of the wire is measured to be 180°C in steady operation. Also, the voltage drop and electric current through the wire are measured to be 110 V and 3 A, respectively. Disregarding any heat transfer by radiation, determine the convection heat transfer coefficient for heat transfer between the outer surface of the wire and the air in the room.
An immersion heater utilizing 120 V is used to raise the temperature of a 100 g aluminum cup containing 350 g of ice from -20.0 ºC to a final temperature 35.0 ºC. How much energy is supplied by the immersion heater? cAl = 900 J/kg.ºC, cwater = 4190 J/kg.ºC, Lf,Al = 3.80 x105 J/kg, Lf,water = 3.34 x106J/kg, melting point Al = 660 ºC, boiling point water = 100 ºC, csteam= 2010 J/kg.ºC Clearly state the formulae you’re using and what your letters/symbols mean.
Some incandescent light bulbs are filled with argon, because it is an inert gas. An argon atom has a mass of 6.63 ×10−26×10-26 kg. A)what is the rms speed in meters per second for argon atoms near the filament assuming their tempature is 2650k
An incandescent lightbulb is an inexpensive but highly inefficient device that converts electrical energy into light. It converts about 10 percent of the electrical energy it consumes into light while converting the remaining 90 percent into heat. The glass bulb of the lamp heats up very quickly as a result of absorbing all that heat and dissipating it to the surroundings by convection and radiation. Consider an 8-cm-diameter 60-W lightbulb in a room at 25°C. The emissivity of the glass is 0.9. Assuming that 10 percent of the energy passes through the glass bulb as light with negligible absorption and the rest of the energy is absorbed and dissipated by the bulb itself by natural convection and radiation, determine the equilibrium temperature of the glass bulb. Assume the interior surfaces of the room to be at room temperature.
Suppose you have an antique copper penny in your pocket. Modeling the conduction electrons in the penny as an ideal gas, use results from Chapter 20 to estimate their kinetic energy and root-mean-square (rms) velocity. (Assume that the temperature is 27.1°C.) kinetic energy J rms m/s
Aluminum, copper, gold, and nichrome wires of equal lengths of 1.0 10-1 meter and equal cross-sectional areas of 2.5 10-6 meter2 are at 20.0°C. Which wire has the greatest electrical resistance?
An electric current of 5 A passing through a resistor has a measured voltage of 6 V across the resistor. The resistor is cylindrical with a diameter of 2.5 cm and length of 15 cm. The resistor has a uniform temperature of 90°C and the room air temperature is 20°C. Assuming that heat transfer by radiation is negligible, determine the heat transfer coefficient by convection.
Copper wire has a resistivity ρ = 1.7 × 10-8 Ω⋅m when at 20°C and it has a temperature coefficient α = 3.9 × 10-3 K-1. A solid cylinder of copper of length L = 85 cm and diameter D = 3.5 mm has one end held at T1 = 14°C and the other end is held at T2 = 210°C. The temperature increases linearly between the two ends of the cylinder. 1A) Consider a thin slice of the copper cylinder of thickness dx that is located a distance x from the left end of the cylinder. Write an equation for the temperature of this slice in terms of the variables x, L, T1, and T2. The answer to part a is T=( x/L ) T2 + ( 1 - ( x/L ) ) T1 b) Determine the total resistance in milliohms.
Copper wire has a resistivity ρ = 1.7 × 10-8 Ω⋅m when at 20°C and it has a temperature coefficient α = 3.9 × 10-3 K-1. A solid cylinder of copper of length L = 85 cm and diameter D = 3.5 mm has one end held at T1 = 14°C and the other end is held at T2 = 210°C. The temperature increases linearly between the two ends of the cylinder. A) Consider a thin slice of the copper cylinder of thickness dx that is located a distance x from the left end of the cylinder. Write an equation for the temperature of this slice in terms of the variables x, L, T1, and T2. B) Determine the total resistance in milliohms.
Copper wire has a resistivity ρ = 1.7 × 10-8 Ω⋅m when at 20°C and it has a temperature coefficient α = 3.9 × 10-3 K-1. A solid cylinder of copper of length L = 85 cm and diameter D = 3.5 mm has one end held at T1 = 14°C and the other end is held at T2 = 210°C. The temperature increases linearly between the two ends of the cylinder. 1a) Consider a thin slice of the copper cylinder of thickness dx that is located a distance x from the left end of the cylinder. Write an equation for the temperature of this slice in terms of the variables x, L, T1, and T2. 2a) Determine the total resistance in milliohms.
if the heat capacitance for a Container of Aluminum is 270 J/Co and the specific tempreture of Aluminum is 900 J/kg.Co , find the Container mass
按ESC | 即可退出全屏模式 Gas insulation is important for transmission lines, outdoor insulators and Gas-insulated- Substations (GIS). Understanding the breakdown mechanisms and behaviour of insulation materials is key to the optimum design of insulation systems. The speed distribution function of electrons in a gas containing electrons, ions and atoms is controlled by the electric field strength, E, and can be expressed as fo (E, v). It satisfies the relationship of (E, v) dv=1. i) ii) Convert the above electron speed distribution function into an electron energy distribution function that satisfies the relationship f(E, ɛ) dɛ =1 where & is the electron energy and ƒ(E, ɛ) the electron energy distribution function. The electron number density is ne and the atom number density is na in the gas. The ionisation cross section of the atoms by electron impact is a function of electron energy, ɛ, and can be written as σ¡ (ɛ). Similarly, the attachment collision cross section between an electron and an…