A 6m long log has a diameter 50cm at one end and 30cm at the other end and has a specific gravity of 0.75. Two weights are placed on each end of the log causing it to completely submerge. Determine the amount of weights. explanation is not really needed.

Q: Calculate the resultant force vector using the table and diagram below. Round your answers to 1…

A: From figure:Fx=F1cosθ1-F2cosθ2Fy=-F1sinθ1-F2sinθ2ResultantFR=Fxi+Fyj

Q: If a 150 lb (pound) weight is lifted 2 feet upwards, how much work was done? Give answer in [lb ft].…

A: To determine the work done for given weight and displacement.   Given, Weight = 150 lb Displacement…

Q: PROBLEM 1: A barge is pulled by two tugboats. If the resultant of the forces exerted by the tugboats…

A:

Q: A baseline was measured using a 100m tape which is standardized at 15°C with a standar pull of 10kg.…

A:

Q: • Part A Replace the loading system acting on the beam by an equivalent resultant force and couple…

A:

Q: 0.60 m W.S. FIGURE EE dreamstie

A:

Q: Problem 4: Calculate the flexural stresses in the concrete and steel for the beams shown using the…

A:

Q: Replace the loading acting on the beam by a single resultant force. (Figure 1) Figure 1 of 1…

A: Given data : Determine F , Thetha and x ?

Q: Make an introduction about Fluid Displacement Method for Measuring Volume Solids. Cite your…

A: To find the volume of an object or solid we can use the fluid displacement method.

Q: cantiliver shown in the diagram has a length L1=9 m and subjected to a uniformly distributed load q2…

A:

Q: An aluminum block (SG=2.5) has a dimension of 0.14 m x 0.14 m xh meters. It is floating in mercury…

A: Given data in question  Aluminum block Specific gravity  Mercury fluid To find out  Weight of the…

Q: Q3) A Your company has been asked you to design a storage tank for liquid petroleum gas. The…

A:

Q: Solve using paper:PROBLEM 19: The horizontal top of a concrete column is subjected to the system of…

A: First, we need to identify the forces and their positions. The forces given are: 4 kN at 0.8 m, 3…

Q: Given a bar of diameter d subjected to torques as shown in Figure 2. Determine d to satisfy the…

A: Answer  We know from Torsion equation is given by  TJ=ζr=GθL From above Torsion equation we get…

Q: A wood beam is strengthened using two steel plates as shown in the figure below. 1 -100 mm- q= 5.0…

A:

Q: Given data : Work done=20 Joule Displacement=5 m Calcualte force applied

A: This question is related with mechanics . In this question we are provided with value of work done…

Q: Make 2 free body diagrams

A: To make free body diagram

Q: After putting it off for three months, you decide to finally trim the tree in your front yard. You…

A:

Q: has an order to manufacture 5000 hanging vases to hold ½ pt. of water when full. The vases are…

A: Given:- 5000=manufacture 1/2 point of water  height=8 in weighs =130 lb per cu ft To find:- weight…

Q: Consider the beam shown in (Figure 1). Suppose that P = 9 kip. w = 1.7 kip/ft. Point E is just to…

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.