A 60-Ohm resistor and a 20-Ohm resistor are connected in series across a 50 V dc source. What is the voltage across the 60-Ohm resistor?

Q: A series RLC circuit containing a resistance of 30Q, an inducta 0.25H, and a capacitor of 120UF are ...

A:

Q: shown, solve for IB, IC, VCE, IC(sat) and VCE(off). Also, construct a dc load line showing the value...

A:

Q: v(t) = -3e-3t V and i(t) = 4 + 2e-3t A fort >0

A: Designing a circuit can be done in multiple way. It is depend on the designer and their knowledge. B...

Q: Find the IT in circuit * It 5R VT loov O 100 V O 10 A 13.33 C/S O 13.33 J/S

A: Given,

Q: the Leq between point A &B is A loH 3 5H O 15 H О 20 Н О 10 н О 5Н

A: When inductance connected in series then current flowing through inductance will be same but voltage...

Q: 5) If the load impedance is 10 + j10 2 then the power factor will be a) 0.5 b) 0.707 c) 0 d) Cannot ...

A: Angle of impedance is the power factor angle . And power factor = cos(power factor angle ) Power fac...

Q: Determine the maximum voltage that can be applied across the series combination of a 150 ohm, 2 watt...

A: First calculate rated current in each resistor element.  Now two elements are connected in series so...

Q: Q3] Suppose A is a one-dimension array with 12 elements is entered into list box. Write a program se...

A: Answer - Code for Form load is -   Dim Max, MaxLocation, Min, MinLocation As Double   Dim ...

Q: Q7:- (a) Design the circuit in figure below to maintain VL at 12V for a load current (IL) variation ...

A:

Q: 20. For the transistor circuit shown below IB = 35 HA and VBE = 0.7V The value of RB would be 12V A....

A:

Q: An 8-pole, 50 Hz induction motor has a full load slip of 2.5 percent and a maximum torque of twice t...

A:

Q: IV. Magnetic Force on Current-carrying Conductors A horizontal rod 0.25 m long is mounted on a balan...

A: Solution (IV) - Magnetic Force on the current carrying conductors -The length of the rod is,L=0.25mT...

Q: BACT1O CITY +10V 3.0ka 430ka Draw the Load Line SI B=50 2.0k 2.

A: We need to find load line equation for given circuit

Q: Q3: Find I, in the network in fig.(3) using superposition YA lose 2023 YoV 2A IX Fig.3

A:

Q: For the given system transfer function below, find the value of the rise time. 10 G(s) = %3D +44 Ans...

A:

Q: For the given op-amp circuit, determine R such that Av=Vo/Vi is 20.

A:

Q: What is the maximum period obtainable from the following generator? Xn+1 = (aXn) mod 24 What should ...

A:

Q: What is the parameter that determines the intensity of the MRI signal? If a field is applied to a ce...

A: MRI signal : The signal which is produced by the magnetization is known as MRI signal this signal is...

Q: a I1 620°A 212 Y.079 I3 -j12 b 12 I4 j20 V.07 I2 I5 e

A:

Q: A digital ramp ADC (with timing diagram) has the following operational values: Clock frequency = 1 M...

A:

Q: 12. For the circuit shown below, by assuming B = 150 and VBE = 0.7V, the best approximation for the ...

A: IC denotes the current which is from the collector terminal of the transistor.

Q: For the circuit shown, solve for VB. VE , IC. VC. and VCE. Also, calculate IC(sat) and VCE(off). Fin...

A: As per company guidelines, we are supposed to answer the first 3 subparts of the question. Kindly re...

Q: QI/A) What is the resistance of a copper wire 75 m long and 2 min in diameter (at T= 40°C)? If the r...

A:

Q: 6.31 If v(0) = 0, find v(f), i,(1), and i>(t) in the circuit of %3D Fig. 6.63.

A:

Q: 7. Consider the two systems in Figure 4.40. R(s) K1 K2 | Y(s) 0.0099 (i) R(s) K2 Y(s) 0.09 + 0.09 (i...

A:

Q: Question 8 The parity check matrix is given as shown: 1000010 0 10 0 I 11 H = 0010110 0 0 01011 Dete...

A: From the given table  Minimum non zero hamming weight  dmin= 3    

Q: 2.2 k2 10 kN 4.7 kN 33 k2 2 V 33 kN 47 kN

A:

Q: v(t) = 4 + 2e-3tV and i(t) = -3e-3t A fort > 0

A: A ideal capacitor and inductor does not consume the active power from the source. It store and relea...

Q: From the given circuit diagram, what is the value of diode current? 1k R1 D2 Si- 8V+ D1 Ge O 7.3 mA ...

A: Silicon diode cut in voltage is 0.7 volts Germanium diode cut in voltage is 0.3 volts

Q: A Mealy sequential circuit has one input (X) and one output (Z). The circuit should transmit its inp...

A: The sequence are given below, X=00110 and Z=00111 

Q: L2 500 mH R1 100 N ww C2 25 µF R2 v,(t) (A 50 Hz L1 800 mH 200 N C1 12 µF

A:

Q: An RC circuit includes a basic switch. In position "a", the battery, resistor and capacitor are conn...

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for y...

Q: 1) a) For the circuit shown , let R= 1kohm, L1 = 10mH, C1= 5nF. Calculate the values of Z, Phase Shi...

A: The solution is given 

Q: A DC machine (6kW, 120V, 1200rpm) has the following magnetization characteristics when running at th...

A: DC Machine :It is an electric machine that produces direct current .They are of two types DC motor a...

Q: A 50 MVA, 30 kV, three-phase, 60 Hz synchronous generator has a synchronous reactance of 0.9 Q per p...

A: The solution is given below

Q: The conductivity of Ag is about 61.4MS/m. What is the resistance of a 2m length Ag wire having 1mm d...

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source, eithe...

Q: A magnetomotive force is supplied by a current of 1 A through 100 turns. The magnetic circuit consis...

A:

Q: the Current I equal in network 2.n loA (1) O 10 A O - 10 A 3.33 O 6.66

A: Current flowing through the series connected elements are same.

Q: I need handwritten only or dislike (a) Using the Routh stability criterion, determine the range of v...

A: The solution is given below 

Q: 4. For the circuit below, = 24230° v, z, = 2 + j2 SN, z, 4 - j3 2, Z, 6 + j8 2, Z, = 8 - j6 Q, Z, = ...

A: The solution is given below 

Q: Explain some of the factors that have contributed to the delays in undersea cable maintenance.

A: Communication is the exchange of information. Information can be imparted to either individuals or a...

Q: V.078 220°A j12 I2 I3 I4 -j207 32 I1

A:

Q: QUESTION 1 Bridge circuit with R1- R2 = 500 ohm, R3= 400 Ohm (R3 is a sensor) and Vs = 10 volt Find ...

A:

Q: Consider the circuit diagram where Vs = 2300 Vrms. Z, Z, V Z, Z, Find: 1. The apparent power deliver...

A: Apparent power delivered by the source = Sum of the Apparent power obsorbed by the Loads. apparent p...

Q: 2. The magnetic circuit of Fig 1.26 consists of rings of magnetic material in a stack of height h. T...

A:

Q: calculate the current for each resistance (1) Ali R, R, 13n 48 n 12V E, R, E, 2n

A:

Q: + vp - si to 12V

A:

Q: From the circuit below, determine the output peak voltage Vm ? Np:Ns 6:1 D. 120 Vac out 60 Hz Da Dg ...

A: Peak inverse voltage is the maximum value of voltage across diode when diode is in reverse biased. F...

Q: Consider the circuit diagram where Vs = 230020 Vrms Z, Z, Z, Find: 1. The apparent power delivered b...

A:

Q: 1. For the circuit shown, solve for IB, IC, VCE, IC(sat) and VCE(off). Also, construct a dc load lin...

A: We need to find out the current and voltage for given circuit

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.