A 6.6 kV / 440 V, 50 Hz, single phase transformer is to have an approximate e m f per turn of 88 V Calculate (A) the number of primary and secondary turns (B) the maximum value of flux density in Tesla, if the cross sectional area of core is 45 cm2 (C) Load voltage, if the voltage regulation is 2 %

A 6.6 kV / 440 V, 50 Hz, single phase transformer is to have an approximate e m f per turn of 88 V Calculate (A) the number of primary and secondary turns (B) the maximum value of flux density in Tesla, if the cross sectional area of core is 45 cm2 (C) Load voltage, if the voltage regulation is 2 %

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter4: Symbols

Section: Chapter Questions

Problem 7SQ: The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d....

See similar textbooks

Related questions

Q: A 10 kVA, 2400/240 V, 60 Hz single phase transformer has Z, = 5.2 + j12.5 ohms and Z2 = 0.06 + j0.12…

A: In this question, We need to calculate the load voltage if Primary voltage and frequency is rated.…

Q: The efficiency of a 20 kVA 15.4 / 0.4 kV three-phase power transformer is 79.1% for a load with unit…

A: Given: For a 20 kVA, 15.4/0.4 kV, 3-phase star-delta transformer, Relative idle or no-load %I0=30,…

Q: A 12 kVA, 58HZ, single-phase transformer has a turns ratio of 10:1 and is supplied from a 2.8 kV…

A: Dear student as per our guidelines we are supposed to solve only one question in which it should…

Q: A single-phase, 25 kVA transformer has 500 turns on the primary winding and 40 turns on the…

Q: A l-phase, 10-kVA, 500/250-V, 50-Hz transformer has the following constants: Reactance : primary 0.2…

A: In this question, We need to determine the reading of the instrument for the open circuit test and…

Q: 3.57 A two-winding single-phase transformer rated 60 kVA, 240/1200 V, 60 Hz, has an efficiency of…

A: Transformer : A transformer is a stationary device that transmits electrical energy from one circuit…

Q: A 10 kVA, 440/110 volt, single-phase transformer has an efficiency of 96% at a rated load of unity…

Q: Determine the number of turns of the primary and the secondary windings of a 60 Hz, 240/120 V ideal…

A: We have an transformer with, Primary Voltage (v1) = 240 V Secondary Voltage (V2) = 120 V Flux (ϕm) =…

Q: A single phase 500/200 V ,55HZ transformer has an efficiency of 98% at full-load. Determine the…

A: Given input frequency = 55 Hz and no load terminal voltage = 200 volts full load terminal voltage =…

Q: Maximum flux density in the core of 225 V/3000 V, 50 Hz single-phase transformer is 1.3 Wb/m?, If…

A: Given: A 225 V/3000 V, 50 Hz single phase transformer has, Maximum flux density = 1.3 Wbm2 EMF per…

Q: Impedance of single phase., two winding transformer referred to primary side is 0.1 + j0.6 p.u. The…

A: Given values are - S=1kVAZPP.U=0.1+j0.6V1V2=200400

Q: A single-phase, 2,959 VA, 2200/220 transformer has the following open circuit and short circuit test…

A: 'Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A single-phase 100 kVA, 2400/240 V, two-winding transformer will be used as a step-down…

A: single-phase Two winding transformer step down 100 kVA, 2400/240 V, auto-transformer Step down…

Q: A 6600/600V., 50 Hz single-phase transformer has a maximum flux density of 1.35T in its core. If the…

Q: kV / 220 V, 50 Hz, single phase transformer is to have an approximate e m f per turn of 44 V…

A: In this we will find turns and maximum flux density of transformer...

Q: A 10-kVA, 2000/400-V, single-phase transformer has resistances and leakage reactances as follows :…

A: The information we have : Primary voltage, V1 = 2000 V Secondary voltage, V2 = 400 V So,…

Q: 55 V / 220 V, 50 Hz single phase transformer, high voltage (secondary) windings are left idle and…

A: Winding resistance of the secondary referred to the primary, R2'=0.015 Ω

Q: A 10-kVA, single-phase transformer has its primary connected to a 2000-V supply. It has 60 turns on…

Q: 17. A 20kVA, 2400/240 single phase transformer has a full load copper and core loss of 1,060 W and…

A: Total looses = iron losses + copper losses = iron losses + x2 full load copper…

Q: The EMF induced in the secondary winding of a 50 Hz single-phase transformer having 500 turns on its…

Q: The % resistance and the % leakage reactance of a 5 kVA, 220 V / 440 V, 50 Hz, single phase…

A: Given values are - Resistance%=3%ResistancePer unit=0.03Reactance%=4%ReactancePer…

Q: A short-circuit test was performed on a 10kVA, 2000/400 V single phase transformer. The instruments…

Q: Q.2 (a) Give TWO reasons why we must use transformer in electrical system. (b) A single-phase…

A: a) To reduce transmission line losses, transformers are utilised to boost up the input voltage.…

Q: QI An 11,000/230-V, 150-kVA, 50-Hz, 1-phase transformer has a core loss of 1.4 kW and full-load…

A: Given data: Core loss = 1.4 kW Full load Copper loss= 1.6 kW Full load KVA =150 Power factor…

Q: 55 V / 220 V, 50 Hz single phase transformer, high voltage (secondary) windings are left idle and…

A: Referring the resistance at primary side, R1=0.026 Ωand the inductance at secondary side,X1=0.045…

Q: Question- The net cross-sectional area of a single-phase, 50 Hz transformer is 500 cm? having 400…

A: The specifications of the transformer are given as:

Q: A 1-phase, 10-KVA, 500/250-V, 50-Hz transformer has the following constants: Reactance: primary 0.2…

A: Solve for short circuit current

Q: 2. Determine the core area, the number of turns and pos the tapping point for a 500-kVA, 50-Hz,…

A: In this question auto transformer is given....We have to find out core area , no of turns and…

Q: Rated values of an ideal single-phase transformer; 3000VA, 380V/220V’ tour. If the network frequency…

Q: A 600 kVA, 1-ph transformer has an efficiency of 92 % both at full- oad and half-load at unity power…

Q: 1. A 11000/230V, 150KVA, 50 Hz single phase transformer has core loss of 1.4kW and full load copper…

Q: 2.2 A single phase transformer with its primary winding supplied from a 50 Hz supply has 100 turns…

Q: In a 25-kVA, 2000/200 V, single-phase transformer, the iron and full-load copper losses are 350 and…

Q: The maximum flux density in the core of a 250/3000V, 50Hz single phase transformer is 1.2 Wb/m2 . If…

Q: A 12 kVA, 58HZ, single-phase transformer has a turns ratio of 18:1 and is supplied from a 2.7 kV…

A: Given N1:N2=18:1V1=2.7kVf=58Hz

Q: Q1 Calculate the daily efficiency of a single-phase transformer with an output capacity of 350 kVA…

Q: distribution transformer is connected to a 2,300 V, 60 Hz ac source with its primary windings equal…

A: In this question we will find mutual flux, maximum flux density etc..

Q: determine (i) the core loss current(Ic) (ii) the power factor on no-load and (iii) the magnetizing…

A: Given,the measurement is taken while the secondary of transformer is open circuited. So we can say…

Q: 75 kVA, 2400/4800 V, 50 Hz one-phase two-winding transformer will be connected as auto transformer…

Q: A 16 kVA, 58Hz, single - phase transformer has a turns ratio of 14: 2 and is supplied from a 2.7 kV…

Q: . A 15kVA single-phase transformer, for 10000V/440V at no load, has resistances and leakage…

A: In this question, We need to determine the value of the secondary voltage at full load, 0.85 power…

Q: Power transformer A, has Rated power of 150MVA. Line voltage of 330/66 kV Frequency=50Hz Connection…

A: The Figure shows the load sharing in two transformers referred to HV side. V2 = E2A -IAZA…

Q: (a) Consider the concept of magnetic circuit to explain the effect of air gap on the flow of flux.…

Q: A 270 kVA transformer has primary and secondary winding resistances of 0.6Ω, and 0.0016Ω…

A: According to question we have to find the efficiency of transformer at full load with the help of…

Q: A 20-KVA, 20,000/480-V, 60-Hz distribution transformer is tested with the following results:…

A: Given Parameters of a distribution transformer. We need to sketch the per equivalent circuit.…

Q: Calculate the daily efficiency of a single-phase transformer with an output capacity of 350 kVA at…

A: “Since you have posted a question with multiple sub-parts, we will solve first four subparts for…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

27. A 6.6 kV / 440 V, 50 Hz, single phase transformer is to have an approximate e m f per turn of 88 V Calculate (A) the number of primary and secondary turns (B) the maximum value of flux density in Tesla, if the cross sectional area of core is 45 cm2 (C) Load voltage, if the voltage regulation is 2 %.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
Question three: A single phase, 4600/460 V, 60 Hz, transformer is connected to a 60 Hz, 4600V power supply. The maximum flux density in the core is 0.85 T. If the induced voltage per turn in 10V, determine (a) The primary turns (N1) and the secondary turns (N). (b) The cross-sectional area (A) of the core.
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
a)The voltage per winding of 220V/12V, 60 Hz single phase core transformer is 1V. If the maximum flux density in the core is 1.5 T, which of the following is the cross-sectional area of the core in cm²? 0.0030 0.0060 30 25 50 0.0050 0.0025 60 b) The voltage per winding of 220V/12V, 50 Hz single phase core transformer is 2V. If the maximum flux density in the core is 1.5 T, which of the following is the cross-sectional area of the core in cm²? 0.0030 0.0060 30 25 60 0.0050 0.0025 50
Solve the problem and illustrate the circuit. Answers must be in 3 decimal places A 480/220 V, 60-hz single phase transformer has a maximum flux density of 1 Tesla. If the voltage/induced per turn is 1.5 Volts, determine the cross-sectional area in the core in cm and the primary and secondary number of turns.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
A single-phase transformer is required to step down the voltage from 1100 V to 400 V at 50 Hz. The [5]core has a cross-sectional area of 25 cm? and the maximum flux density is 5Wb/m?. Determine thenumber of turns of the primary and secondary windings.
It is desired to have a 4.13 mWb maximum core flux in a transformer at 110V and 50 Hz. Determine the required number of turns in the primary.
3. The maximum flux density in the core of 240/2400 V, 50 Hz, single phase transformer is 1 Wb/m² if the e.m.f. per turn is 8 V, the area of the core is a) 0.132 b) 0.086 c) 0.241 d) 0.036 (125 mark)
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
The voltage per winding of the 220V/12V, 60 Hz single phase core transformer is 1V. If the maximum flux density in the core is 1.5 T, which of the following is the cross-sectional area of the core in cm2
A single-phase 500 V/100 V, 50 Hz transformer has a maximum core flux density of 1.5 T and an effective core cross-sectional area of 50 cm2. Determine the number of primary and secondary turns.