A 50m tape has the conditions -The standard temperature  is 35degrees Celsius and the site temperature is 40degrees Celsius resulting to a temperature correction factor=0.01m for the 50 m tape -The standard pull is 6 kg but the applied pull is 2.4 kg resulting to a correction due to pull= -0.03m for the 50 m tape. a) Determine the reading to be laid out to get a length of 50m b) Determine the reading to be laid out to get a length of 1500m

Q: 11.) To check the setting out of the corners of a 20 x 25 m rectangular building, the diagonals were…

A: Given data -Rectangular building = 20×25 m Steel tape length = 50 m Pulling tension= 50 N…

Q: A stadia rod held at a distant point B is sighted by an instrument set up at A. Determine the length…

A: Solution:-

Q: 3.57 m 5.12 m 2.53 m 3.26 m 4.26 m 6.09 m| BM1 ELEV = 232 m ТР1 ТР2 BM2 Station BS HI FS Elevation…

A: To find :- elevation of station BM-2 and to fill out the table.

Q: A two points want to be fixed on the ground with a slope of 6 % with horizontal distance of 265 m. A…

A:

Q: III. A load of length 2m and intensity 2kN/m crosses the simply supported beam AB as shown.…

A: A load of length 2m and intensity 2kN/m crosses the simply supported beam as shown in figure.  We…

Q: 10.) A line XY is to be set out from point X using a 30 m steel tape. The horizontal length of XY…

A: Given data -Tape length (l) = 30 m Horizontal distance of XY (D) = 20.000 m Standardized lenght of…

Q: find the stresses on the plane 45 Draw

A:

Q: Considering the beam provided. If El = 200000 kNm² and using any method. Determine the difference in…

A:

Q: Help me, thank you! A 100- m steel tape is used to measure the distance of the line and found to be…

A: Surveying mainly considers the branch of measurement of the points on the ground surface for the…

Q: A tape 30 m long, 0.6 cm wide and 0.5 mm thick was used to measure a distance of -1000 m at a…

A: Given:  tape 30m long                                                        width = 0.6cm thickness…

Q: > 1.5 kr.m A 2 find the deflection at B by Double integration method tiu 10 kN

A:

Q: A 50 m tape of standard length has a weight of 0.05 kg/m, with a cross b) sectional area of 0.04…

A:

Q: 1. The manometers are suitable for comparatively C. very high A. low B. high pressures. D. none of…

A: Manometers are used to measure the pressure.

Q: 2. A 30m tape has the following condition The standard temp is 20deg Celsius and the site temp is…

A: Given data: correction for temperature Ctemp =0.02 m correction for pull Cp =-0.01 m

Q: Problem 6.23 (Ans. 9.93 mm) Wp = 12 kN/m WL 16 kN/m 480 mm 550 mm 4 #22 -6 m- 300 mm 70 mm

A: There are few data Missing in the question. In order to get the given answer 9.93 mm I have the…

Q: use the virtual work method to determine the deflection at point C of the beam shown

A: Given :- A beam is shown with two point load of 200 kN and 100 kN Modulus of elasticity constant (E)…

Q: 1.a.find interval latitude moment

A:

Q: use slope deflection m

A:

Q: A steel tape has nominal length 30.000 m. was used to measure a base line A to B. The standard…

A: as this question is related to surveying. as per the question , we have to determine the number of…

Q: Q.1.17 A vibrating SDOF system is viscously damped such that ratio of two consecutive amplitudes is…

A: As here given is SDOF SYSTEM Amplitude are 1.00 and 0.60 We need to know logarithmic decrement.

Q: 80mm Q2/ 20mm 70mm IF : N.A. |= 15.52 mm* V=10 KN 160 mm 110mm Compute the shear at horizontal layer…

A: The shear stress at horizontal layer 20 mm apart from top with layer just in the flange is given by,…

Q: A 100 m tape weighing 3 kg was standardized and found to be 0.02 m short at temperature of 10degC…

A:

Q: 1. A steel tape with a coefficient of linear expansion of 0.0000115/degree Celsius is known to be 50…

A: If temperature at time of measurement (TM) is more than the temperature at the time of manufacture…

Q: 10 kN 80 kN/m В A D 4 m 1 m'1m

A:

Q: 5. Line AB was measured to be 2465.75 m when using a 100 m steel tape supported only at the ends…

A: Measured length = L = 2465.75m Steel tape length = 100m Pull applied for measurement = P = 9Kg…

Q: 5) A line measured with a 40.0 m long steel tape was determined to be 7500.0 m when the average…

A:

Q: 4. Line AB was measured and the result is 834m. It is measured using a 30m tape that is 0.002m too…

A:

Q: Q.12 The logarithmic decrement for a damped freely vibrating SDOF system is 0.08. The damping ratio…

A: Now we find, damping ratio is in percentage

Q: A 30 m. tape was standardized and was found to be 0.0022 m. too long than the standard length at…

A:

Q: Engineer used SUP tape in asuring an Clined distance. The measured length on the slope was recorded…

A: Tm=35T0=28PS=12P0=8A=0.03cm2=3mm2E=200×103 N/mm2 (assumed as not given in question)

Q: Q.13 A system having natural frequency 20 rad/sec and damping ratio of 10% is subjected to a…

A: Given, Natural frequency=20rad/sec Damping ratio = 10% Harmonic force =50sin(100t) kN

Q: recheck with solution please. interpolate Specimen No. Time (second) Penetration (mm) 1. 30 40…

A: Interpolation is a technique with which we can find the value between two given points .

Q: 13. A distance between points A and B is measured and recorded as 123.456 m, using a tape that has a…

A:

Q: A 30-meter steel tape is of standard length under a pull of 6 kilos and temperature of 20 degree…

A:

Q: A theodolite was set up at station A and its height of set up was taken as 2.22m. A stadia rod held…

A:

Q: Situation #6: A steel marine propeller is to transmit 4.5 MW at 3 r/s without exceeding a shearing…

A:

Q: Q.29 In SDOF system, the frequency ratio is 0.50 and damping ratio is 10%. The dynamic magnificator…

A: In SDOF SYSTEM, frequency ratio =0.5 Damping ratio = 10%

Q: Two forces are applied to the construction bracket as shown. Determine the angle e which makes the…

A: The free-body diagram is shown below,

Q: التاريخ: 1.5 KN A C A 2 2 S с Find the deflection at B by الموضوع:. токи Double integration method

A: EI = constant = KNm2

Q: 6 A theodolite was set up near the middle of the points "P" and "Q". If the height of the instrument…

A:

Q: Determine the minimum size óf glåss tübing that can be used to measure water level, if the capillary…

A:

Q: 9.) A steel tape of nominal length 30 m was used to transfer a level from point C1 near the base of…

A: Given data - Nominal length of steel tape( l ) = 30m Standardised length ( l' ) = 30.015m…

Construction Surveys

A construction survey is a survey done on a construction site to mark construction activities and for laying out positions for construction equipment. It includes evaluating and estimating construction activities before the beginning of the project.