Answered: A 5 in diameter 4 splines shaft ( d=…

A 5 in diameter 4 splines shaft ( d= 0.85D, w= 0.24D, h= 0.075D ) and permanent fit has a compressive force of 3000 lb. Find the compressive stress if hub length is 2 1/2 in. Ans. 800 psi

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Related questions

Q: Q3\ The cantilevered bar shown in the fig. made from steel Cold-drawn with (Sy = 280 MPa) and is…

Q: A steel shaft in the form of a solid body circular rod or a circular tube can be manufactured.…

Q: For the disc saw shown in the figure below a key is used to transfer a torque of 20 Nm. Calculate…

Q: A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in…

A: Coupling : It is a mechanical element which connect the shaft from another also it is used to…

Q: Write legibly, provide manual step by step solution, and diagram for below given problem. A 100 mm…

Q: A shaft is to be fitted with a flanged coupling having 8 bolts on a circle of diameter 150 mm. The…

Q: A hollow aluminium tube used in a roof structure has an outside diameter 104mm and an inside…

A: A) Angle of twist for the given max shear stress in a hollow shaft: The angle of twist of a hollow…

Q: 6 spline shaft (d= 0.80D, w= 0.25D, h= 0.10D) and to slide when under load has a diameter of 4 in.…

Q: the propeller on a ship shown in figure qi is subjected to a compressive axial force f of 180 kn as…

Q: igure Q6(b) shows a cantilever shaft made of steel subjected to several loading T = 5kNm, M =…

Q: Find the diameter of a solid steel shaft to transmit 18 kW at 990 r.p.m. The ultimate shear stress…

Q: A hollow simple supported shaft 3m made of steel with di/do of 0.6. The shaft is subjected to a…

A: Given: Length of the shaft=3mDiDo=0.6 or Di=0.6DoBending moment (M)=4kNPower tranmitted…

Q: A steel shaft in the form of a solid body circular rod or a circular tube can be manufactured.…

A: Given, Torque, T=1200 N.m The maximum permissible unit torsion angle, θ=0.750 /m=75×π180 rad…

Q: Q4-A shaft (55 mm) diameter is transmit power of 200 W at 1200 rpm, the maximum shear stress of (80…

A: Given data: - The diameter of the shaft is d = 55 mm. The power transmit is P = 200 W. The speed of…

Q: A hollow cylinder is used as a torque sensing element with r= 2.5 cm, ro=3.3 cm and L=15 cm.…

A: Given:- T=30 N-mG=8×1010N/m2ri=2.5cm=0.025mr0=3.3cm=0.033mL=15cm=0.15mθ=45° To find:- Size of solid…

Q: Example 1 A high strength steel band saw, 20 mm wide by 0.80 mm thick, runs over pulleys 600 mm in…

A: Given data: The width of band is w=20 mm The thickness of band is t=0.8 mm The diameter of pulley is…

Q: A column supports a compressive load of 360KN. Determine the outside diameter of column if inside…

Q: a b A B Figure P-319 and P-320

A: The calculated maximum torque that can be applied.

Q: A solid steel shaft of radius b is to be pressed into a wrought iron hub of outer radius c and…

A: A solid steel shaft of radius b is to be pressed into a wrought iron hub of outer radius c and…

Q: S. Fig Q5 shows a shaft of gearbox rotating about x axis. Shafi BC is a solid shalt with dircular…

Q: MACHINE DESIGN 1 ELEMENT 2" dia 20 150 PROBLEM: The shaft in the figure is rigidly attached to the…

Q: 8. A 2.5 in diameter 10 spline shaft ( d= 0.86D, w= 0.156D, h= 0.07D ) to slide when not under load…

Q: Example 7.8: (Application of equation(7.42) for a thin hollow circular bar) (a) Obtain the value of…

Q: hardest point in the embedment A or B of the element shown in the figure. This bar is made of hot…

Q: Figure Q1 shows a solid steel shaft AF which is supported by frictionless bearings at B and F. It is…

Q: 3. A welded steel cylindrical drum made of a 10-mm plate has an internal diameter of 1.20 m. Compute…

A: Given:d=1.2 mP=1.5 MPaμ=0.30E=200 GPat=10 mm

Q: Find the diameter of the spring wire and number of active turns required

Q: Example 1 A shaft is transmitting 100 kW at 160 rp.m. Find a suitable diameter for the shaft, if the…

A: Stress: When a component or a part is subjected to any external force, a resisting force will be…

Q: Consider the case of shafts subjected to bending moment only. Figure Q2 shows a pair of wheels of a…

A: Given:- P=50kN Gauge length= 1.4m Max stress=100MPa k=dido=0.5 To find:- 1) Diameter of axel, d 2)…

Q: bar of dimension 180 mm x 55 mm x 30 mm, is subjected to an axial pull of 70 kN. The measured…

Q: a square thread power screw, given that: F= 6.4 kN Pitch = 5 mm Major diameter = 32 mm Total raising…

A: GIVEN:F=6.4KNPITCH P=5mmMAJOR DIAMETER D=32mmtorque T=28N-m

Q: A steel (E= 207 GPa, v =0.3) collar with a 5 mm outside diameter and a 30.00 mm hole diameter will…

Q: Two solid shafts, 50 mm in diameter, are connected by a flange coupling with six bolts and a pitch…

Q: Example 3.8. A lever is keyed to a shaft of 100 mm diameter. The width of the key is 12 mm and the…

Q: A flanged bolt coupling consists of six 2-in. steel bolts evenly spaced around a bolt circle 12 in.…

A: To find : Find the torque that can be applied. Given : Diameter of steel bolts ds= 1/2 in Diameter…

Q: The figure below shows a stepped shaft having D = 35 mm, d = 25 mm, and r= 3 mm. The shaft is made…

A: Given Data: The ultimate tensile strength of the shaft is, σut=450 MPa. The corrected fatigue…

Q: SAMPLE PROBLEM 300mm Py - 90 - The figure shows an eccentrically loaded bracket. P=20 kN. Bolt…

A: Bolt is defined as the material have to join the two materials like fasteners and thread together.…

Q: A steel bar carrying 3000kN load,F, is attached to a support by a round pin 0.3m in diameter.…

A: Given data: The magnitude of the load, F = 3000 kN. The diameter of the pin, d = 0.3 m. Calculate…

Q: A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric…

A: Given Su = 345 Mpa Force = 13 kN Given figure

Q: A shaft ABCD 70 mm in diameter is subjected to torques of 1500 N-m at B and 1100 N-m at C acting in…

Q: A thin tube of uniform thickness 5 mm and square cross section, shown below, is subject to a torque…

Q: Figure shows a cantilever shaft made of steel subjected to several loading T=5kNm, M=2.5kNm, and…

Q: Steel shaft can be produced as solid body or circular tube with circular tube. The shaft must bear a…

Q: A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in…

Q: The figure below shows a boat propeller mounted on a drive shaft with a 7 mm diameter (d)…

A: Given: Diameter of the pin d=7mmDiameter of the drive shaft D=69mmYield stress σy=427MPaUltimate…

Q: Figure Q6(b) shows a cantilever shaft made of steel subjected to several loading T = 5kNm, M =…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Write legibly, provide manual step by step solution, and diagram for below given problem.

A 5 in diameter 4 splines shaft ( d= 0.85D, w= 0.24D, h= 0.075D ) and permanent fit has a compressive force of 3000 lb. Find the compressive stress if hub length is 2 1/2 in.

Ans. 800 psi

9. A 5 in diameter 4 splines shaft ( d= 0.85D, w= 0.24D, h= 0.075D ) and permanent fit
has a compressive force of 3000 lb. Find the compressive stress if hub length is 2 1/2 in.
a. 700 psi
b. 700 kPa
c. 800 kPa
d. 800 psi

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, and the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel P E=2.1x10$ N/mm?, Tmax (1-Q¿)
The ultimate stress for the hitch ball is 60,000 ksi. (Capacity) The advertisement information is listed in the photos. 1) What is the maximum shear stress? (Demand) (Note you'll need to use half circle for Q) 2) What is the demand capacity stress ratio? V POWER TORQUE. PTWO011 HITCH BALL BOLA DE ENGANCHE 2" BALL DIAMETER 6000 LB. RATING 3-1/4" SHANK LENGTH PTWO011 POWER TORQUE. HITCH BALL BOLA DE ENGANCHE 1" SHANK DIAMETER
2.A lever secured to a 2 inches round shaft by a steel tapered pin (d = 3/8”) has a pull of 50 lbs at a 30 inch radius from shaft center. Find the unit working stress of the pin.
3) A 25 mm solid round shaft is supported by self-aligning bearings at A and B (the bearings do not support axial loads). Two chain sprockets are attached to the shaft as shown. a. Find the force, F, on the 125 mm diameter sprockets. b. Construct the V-M-N-T diagrams for the shaft. c. Determine the shaft location with the most severe state of stress. d. Sketch the Mohr's circle and find the principal stresses at that location. A 125 mm dia. 50-mm dia. 75 mm 25mm dia. 5000 N 150 mm 75 mm
500 lb in. 1200 lb - in. 400 lb - in. dep-0.9 in. dec =0.75 in. B dan = 0.6 in. Specifications: Shafts AB, BC, CD are solid material. Determine: a) The shaft section in which the maximum shear stress occurs and the magnitude of the stress. Now consider that the shaft is tubular with a 0.300 inner diameter. Determine: b) The shaft section in which the maximum shear stress occurs and the magnitude of the stress.
Problem 1. A shaft with a diameter d = 60 mm must transfer a torque of 350 Nm by using a key joint. The key has the following standard dimensions: b x h x 1= 18 mm X 11 mm x 50 mm. Calculate the stresses.
4. As shown below, the prosthesis is made of two parts a core (Ge=150 ksi) and a tube (G=85 ksi). The prostheses is under torsional torque of 15 lbf.in due to foot movement. a) Determine the maximum torsional stresses in the core and tube. b) Determine the angle of twist 15 Ibf.in 15 lbf.in 15in Diameter 1.5 in Diameter 1in 15 Ibf.in (Answer: a)t, = 23.13 psi; t = 19.67 psi b) = 0.0046 rad)
A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outsude diameter and 90 mm in inside diameter. If the allowable aring stress in the shafts and the bolts is 60 MPa, how many 10 mm diameter steel bolts must be used on a 200 mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?
A collar is fitted as a tight fit on a solid shaft. made before assembly in measuring, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel E=2.1x105 N/mm2 , Tmax = P (1/QG^2)
9:0. محو التحدید blä 10 FIND STRESS IN Aluminum. IF E st= .200000 MPa, Ealu.=7000O MPa 100 kN RALU.=30 MM Aluminum Steel no one 69 MPa 31 MPa 19 MPa 55 MPa bläi 10 find the shear stress in bolt in pin A 60 kN 1m RST = 20 MM
100 kip 10 kip ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of the following are closest to the principal stresses in the shaft? 01 = 31.8 ksi 02 = 76.4 ksi = 94.0 ksi 02 = -62.1 ksi O0g - 14.3 ksi 02 = -6.37 ksi Oo= 7.96 ksi 02 = 9.55 ksi
Solid steel post subjecting torsion. Given that the diameter is 75.05 mm, length is 2.5.05 m and modulus of elasticity of shear is 78.08 GPa. 1. What is torsional rigidity? 2. What is torsional stiffness? 3. What is maximum shear stress in MPa given torques is 540 N-m.