A 5 hp motor (mechanical power), wye connected with a 208V line: a. What is the apparent power drawn by the motor? b. How much line current will it draw if the motor is 90% efficient? c. What is the apparent power drawn by the motor? d. The Power Factor is 90%, what is the real power that is drawn by the moto

A 5 hp motor (mechanical power), wye connected with a 208V line: a. What is the apparent power drawn by the motor? b. How much line current will it draw if the motor is 90% efficient? c. What is the apparent power drawn by the motor? d. The Power Factor is 90%, what is the real power that is drawn by the moto

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 3RQ: 3. What is power factor?

See similar textbooks

Similar questions

A load of 300 ohms is connected to a 240V DC supply. Determine the power in BTU
A find Power of Pen stock ) B I How many Mw con be assumed the Power of generator? suggest the Power of the design
Question 4 a) B M Figure 4 Figure 4 shows the graph of the ripple current. Answer the following i. Describe the function of A. ii. iii. Describe the function of B. Identify the ideal paramater to get the good power supply.
plase answer five a quesion option corrctly 9.In AC circuits, power consumed is A.it depends on the supply voltage B.product of voltage and current C.it depends on the power factor (p.f.) of the circuit in addition to voltage and current D.it depends on the magnitude of the circuit current 10A potential transformer is a A.transformer used with an AC ammeter B.transformer used with an AC voltmeter C.transformer used with a DC voltmeter D.transformer used with a DC ammeter 11. Define Per Unit Quantity A/ Xp.u = x base / x actual per unit B/ Xp.u = X actual / x base per unit C/ Xp.u = x actual / x unit per unit 12./ VS= 1200<0º V ZL= 50 + j60 ohm ZS= j25ohm By taking Zbase = 100 ohm, find Vs (p.u), Zs(p.u), ZL(p.u) A. Vs (p.u) = 1 < 00 p.u Zs(p.u) = j0.20 p.u ZL(p.u) = 66.42<390 p.u B. Vs (p.u) = 1 < 00 p.u Zs(p.u) = j0.25 p.u ZL(p.u) = 42.96<730 p. C. Vs (p.u) = 1 < 00 p.u Zs(p.u) = j0.25 p.u ZL(p.u) = 0.781<50.20 p.u 13. Which of…
Answer the question. 1. What is Alternating Current (AC)? Draw a simple graphical representation of AC. 2. What are the advantages of using alternating current over direct current?
2. A burst controlled triac is feeding a 200 ohm resistive load. The AC supply providing 240 V rms voltage at 60Hz. a) For one cylcle on, four cycles off control calculate the load rms voltage, current, power transferred to the load and efficiency. b) For four cylcles on, one cycle off control calculate the load rms voltage, current, power transferred to the load and efficiency.
3. What is power factor?
a) A sinewave is having a frequency of 50 Hz and instantaneous value of 150 Volts at 1.4 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and ii) The value of voltage at 1.8 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=200 Volts, Time period is 10 milli seconds and P =30 degrees. Vp Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.8 ms = b) Angular frequency D
Question#5 Figure below shows a simple single-phase AC power system with three loads. The voltage source is V = 240 < o°v and the impedances of these three loads are z, = 10 < 30°n Z2 = 10 < 45°0 Z3 = 10 < -90°n V Z, Answer the following questions about this power system. a. Assume that the switch shown in the figure is initially open, and calculate the current I, the power factor, and the real, reactive, and apparent power being supplied by the source. b. How much real, reactive, and apparent power is being consumed by each load with the switch open?
1. A single phase AC circuit consists of a 25 2 pure resistance. It is connected to an AC supply of 230 V at a frequency of 500 Hz. Determine the following: a. current b. power consumed and c. equation for the voltage d. equation for the current
In a given DC motor, the output power is 45 HP, and the copper losses are 2.005 KW. If the rotational losses is one tenth of the output power, find the converted power and the efficiency of the motor. Select one: O a. None O b. Pcony = 36.927 KW and % efficiency = 86.2 % O c. Pcony = 39 KW and % efficiency = 75.8% O d. Pcony = 33.57 KW and % efficiency = 89.2 %
b) A power station has the following daily load cycle as Figure Q1(b) below: Time in Hours 6-8 8-12 12-16 16 20 20-24| 24–6 Load in MW 90 40 60 20 20 20 Figure Q1(b): Daily Load Cycle i) Plot the load curve i) Plot the load duration curve i) Determine energy generated per day