A 3500 ?? load with a power factor of 0.70 leading is fed from a source at 50 ?? with an RMS voltage of 230 ?. A) Determine the load (type and value) to be installed in parallel to correct the power factor to 0.9 lagging. Indicate which is the apparent power value after correction and draw the corresponding power diagrams B) Determine the load (type and value) to be installed in parallel to correct the power factor to 0.9 leading. Draw the corresponding power diagrams.

A 3500 ?? load with a power factor of 0.70 leading is fed from a source at 50 ?? with an RMS voltage of 230 ?. A) Determine the load (type and value) to be installed in parallel to correct the power factor to 0.9 lagging. Indicate which is the apparent power value after correction and draw the corresponding power diagrams B) Determine the load (type and value) to be installed in parallel to correct the power factor to 0.9 leading. Draw the corresponding power diagrams.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

What is the average Power at maximum resistance? Why? What is the effect to the voltage and current when increasing the load resistance?
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
Does Clampor circuit change the peak-to-peak (i.e., rms value)? Justfy
Alternator A (100 kVA, 3-f, 240 V, 60 Hz, 1800 rpm) is operating in parallel with alternator B (125 kVA, 3-f, 240 V, 60 Hz, 1800 rpm). The load of alternator A is 70 kW at 85% pf leading and the load of alternator B is 85 kW at 75% pf leading. Determine the pf of load.
Determine the rms current I as shown in figure 2. Source voltage is already in RMS value(Answer must be in polar formand should be in 4 decimal places).
Generate a conclusion on this following statements: Determine and analyze the voltage regulation characteristics of the alternator with resistive, capacitive, and inductive loading.
FIND THE VALUES INDICATED AND SHOW THE COMPLETE SOLUTION. Peak RMS Phase Instantaneous Average Value Value Value Angle Value (i) ? 30 A ? ? 30 A (j) ? 100.1 V ? 136.1 V
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
5. An alternating current varying sinusoidally with a frequency of 50 Hz has an rms value of 20 A. a) Determine the instantaneous value at 0.0025 seconds. b) Determine the instantaneous value, 0.0125 seconds after passing through a positive maximum value. c) At what time, measured from a positive maximum value, will the instantaneous current be 14.14 A?
Question#5 Figure below shows a simple single-phase AC power system with three loads. The voltage source is V = 240 < o°v and the impedances of these three loads are z, = 10 < 30°n Z2 = 10 < 45°0 Z3 = 10 < -90°n z,
8 = 0 Q1: What does happen if we change two currents? Q2: What does happen if we have a three-phase four poles machine? a Q3: What does happen if we have a two-phase two poles machine? Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali K....p. . --
According to the Reactive Power Compensation Regulation, capacitive reactive power should not exceed what percent of active power in the power plants whose power is greater than 50 KVA?