A 30-m steel tape weighing 1.45 kg is of standard length under a pull of 5 kg, supported for full length. A line 938.55 m long was measured using the tape with a steady pull of 10 kg. If E = 2.0x106 kg/cm2 and unit weight of steel is 7.9x10-3 kg/cm3 , determine: a) cross-sectional area of the tape

A 30-m steel tape weighing 1.45 kg is of standard length under a pull of 5 kg, supported for full length. A line 938.55 m long was measured using the tape with a steady pull of 10 kg. If E = 2.0x106 kg/cm2 and unit weight of steel is 7.9x10-3 kg/cm3 , determine: a) cross-sectional area of the tape

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Two simply supported beams are made up of the same material and are of the same cross-section. Both…

A: given- 2 simply supported beams-same material and same cross-sectionSame UDLspan of beam=2 m and 4…

Q: Two blocks are connected by a light, flexible cable that passes a frictionless pulley. Block A…

Q: A 50-m steel tape is of standard length under a pull of 55 N and a temperature of 20°C when…

A: Tape length, LT=50 m Cross-sectional area of tape, A=0.04 cm2 Weight (mass) of tape, w=0.055…

Q: A heavy 50-m tape having a cross-sectional area of 0.06 cm^2 has been standardized at a tension of…

A: To Determine Elongation of the tape.

Q: estion 25 Determine the maximum bending stress (in MPa, numerical value only) of the beam shown…

Q: A mild steel bar, circular in cross-section, tapers from 40 mm diameter to 20 mm diameter over its…

A: Given data- Mild Steel bars-dia D varies from 40 mm to 20 mmLength L=800 mmAxial load P=20 KNYound…

Q: The RAME type construction is given which works in bending as in the figure: Data: E = 30000daN / m2…

Q: Two simply supported beams are made up of the same material and are of the same cross-section. Both…

A: Given, load on both beam (udl) =w L1=2mL2= 4mEI= same δ1=1 mm

Q: 8. A 30 m steel tape weighs 12.5 g/m and has a cross sectional area of 0.04 cm?. It is of standard…

Q: QUESTION 2 The assembly consists of two A-36 steel rods and a rigid bar BD. Each rod has a diameter…

Q: Q A steel bar 50 cm long and 3 cm × 1 cm in cross-section, when it is subjected simultaneously to an…

A: Given data- Length L=50 cm, 3 cm ×1 cm cross-section Axial pull=50 kN Compressive stress=100 N/mm2…

Q: Two simply supported beams are made up of the same material and are of the same cross-section. Both…

A: Given data L1 = 2m L2 = 4m δc1 = 1mm δc2 = ?

Q: A rigid steel bar is suspended horizontally by 1m steel rod at one end and 2m bronze rod at the…

Q: Answer the problem. Structural theory

A: In this problem, we begin first by examining the given data and illustration. From a structural…

Q: A 50 meter steel tape is suspended in the air between a transit and a vertical rod which is placed…

A: L=50m E=200GPa Po= 10kg w=0.05kg/m

Q: A 10 m B

Q: FlauRE A FIGUPE B

Q: Considering the steel rod at E, how long will its elongation be if it is hollow with an outside…

Q: A rod of diameter 50 cm and length 6 m is hanging vertically and carries an axial load of 10 kN at…

A: Given: The diameter of the rod is 50 cm. The length is 6 m. The load is 10 kN. The unit weight of…

Q: 3) A simply supported beam constructed by four woods nailed together as shown in the figure. If each…

Q: es a uniformly distributed load of 5 kN/m toget s free ends. 2 kN w = 5 kN/ m. 2 m 8 m the…

Q: A steel tape is 100 m long at a standard pull of 65 N. Compute the pull correction in mm if during…

Q: The figure below shows two W150 x 24 members made of A36 steel. They are all connected with pin…

Q: A 50-m steel tape weighs 0.04 kg/m and has a cross-sectional area of 0.022 sq. cm. It measures…

Q: Plastic moment and plastic sectional module for a beam

A: Given:Beam length (L) = 11 mPin supports at x = 0 m and x = 6 mRoller support at x = 11 mDistributed…

Q: A 50-m steel tape weighs 0.04 kg/m and has a cross-sectional area of 0.022 sq. cm. It measures…

Q: A simply supported beam spans L=28ft. A 3/4 inch thick steel plate with a width of b1=3.2ft, and a…

A: Calculate the weight of the plate:

Q: Identical steel bars are used to support a 7400-N load as shown. For the properties of steel bar: A…

Question

A 30-m steel tape weighing 1.45 kg is of standard length under a
pull of 5 kg, supported for full length. A line 938.55 m long was
measured using the tape with a steady pull of 10 kg.
If E = 2.0x106 kg/cm2 and unit weight of steel is 7.9x10-3 kg/cm3
,
determine:
a) cross-sectional area of the tape

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 50 meter steel tape is suspended in the air between a transit and a vertical rod which is placed exactly at the 50 meter mark. The slope of the measured line is 1 degree and 30 minutes. The tension on the tape is 10 kg, and the weight of the tape per unit length is 0.05 kg/m. What normal tension (N) is required in order that the effect of sag will be eliminated when the tape is supported at end points only? The standard pull is 10kg. Tape area is 8 mm2. E = 200 GPa. * 38 378 O 45 O 441
J: A beam is 10.5 m in length and loaded as shown in Figure Q4. If the deflection in the mid-distance between A and B is 3 mm, find the value of flexural rigidity (EI). Find also the value and location of the maximum deflection. 3 kN C 2.5 m + 1 kN/m 6 m B 1 KN 2 m
A 20 m long beam has two supports, A and B. The beam is pinned at Support A and supported by a roller at Support B, and it has an 18kN car in the middle of it. For this system, a free-body diagram (FBD), as well as a shear and bending moment diagram, should be drawn. You could discuss the results and explain the beam's stress. What is the main purpose and concept of this experiment?
MODULUS OF ELASTICITY= 15x10^6
Problem What is the diameter of the steel wire AB if its elongation is 2.10 mm? Consider bar AB to be rigid. Use E = 200 GPa for steel. See figure for details. 50° 3 kN/m A 3.00 m
SITUATION I: A 50-m steel tape is of standard length under a pull of 5kg and a temperature of 22 degree celcius when supported throughout its entire length. The tape weighs 0.06 kg/m, has a cross section area of 0.06 cm'and a modulus of elasticity of 2x10°kg/cm?. The tape was used in the field to measure a distance that was determined to be 525.48. At the time the measurement was made, the constant pull applied was 10kg with the tape supported only at endpoints. During measurement, the temperature was observed to be at an average of 19 degree Celsius. Use alpha a= 12.36x10/degree celcius. 1. Determine the correction due to tension. a. 0.021898 m b. 0.021895 m c. 0.021911 m d. 0.021589 m 2. Determine the correction due to temperature. a. 0.01984 m b. 0.01968 m c. 0.01986 m d. 0.01948 m 3. Determine the correction due to sag. а. 1.8998 m b. 1.8898 m c. 1.8888 m d. 1.9898 m 4. Find the corrected length of the line a. 523.5826 m b. 524.5823 m c. 525.6832 m d. 526.3628 m
A thin beam with a solid rectangular cross-section is loaded as shown in Figure Q7 below. W W L/3 L/3 L/3 Figure Q7 What is the ratio of the maximum to nominal shear stress for the beam described in Question 7? O a. 3:2 O b. 1:4 Ос. 3:1 O d.2:1 O e. 1:2 O f. None of the provided answers are correct. O 8. 1:1
Q1: A simply supported beam and its cross section are shown in Figure. The beam carries a load of (10 kN) as shown. Its self-weight is (3.5 kN/m). Calculate the maximum bending stress at X- X. 3.5 kN/m 1.2 m B 1 10 kN 1.2 m 1.2 m 3.6 m 100 T 150 mm Hole T 300 200 200 --
A 5-kip crate is supported by a pulley system and a horizontal force P.a) Find P and the angle α. Report your answer in kips (1 kip = 1000 lbs).b) For this problem if you double the weight of the crate, will the force P double? Briefly explain why or why not.
A solid steel shaft in a rolling mill transmits 20 kW of power at 2 Hz. Determine the smallest safe diameter if the shear stress is not to exceed 40 MPa and the angle of twist is limited to 6° in a length of 6 m. Use G = 83 GPa. 68.7 mm 48.7 mm 38.7 mm 58.7 mm