A 3-phase delta connected balanced load is supplied from a 3 phase, 430 V supply. The line current is 21 A and the power taken by the load is 6800 W. Find (i) impedance in each branch (ii) power factor and (iii) power consumed if the same load is connected in star. Impedance Power factor Power when connected in star

A 3-phase delta connected balanced load is supplied from a 3 phase, 430 V supply. The line current is 21 A and the power taken by the load is 6800 W. Find (i) impedance in each branch (ii) power factor and (iii) power consumed if the same load is connected in star. Impedance Power factor Power when connected in star

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the complex power for the L2 load?
An 11 kV generating station has four identical 3-phase alternatorsGl, G2, G3 and G4 each of L0 MVA capacity and l2%o reaclarce.There are two section of bus-bar P and Q, linked by a reactor X ratedat 10 MVA with 24o/oreactance. From section Q load is taken througha 6 MVA, i 1kV/66kV step-up transformer (T1) having a reactance of37o. Determine the fault current if a three-phase short-circuit occursnear the high voltage terminal of the transformer (F) as shown inFigure.Assume prefault voltages to be 1 pu and prefault currents to be zero
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
)Two complex loads Z1 and Z2 are connected in parallel and powered by a value voltage effective 7.2 kV and frequency 60 Hz. The first load has a power of 50 kVA and a factor of rear power of 0.9. The second charge has a power of 45 kW and a rear power factorof 0.91. Determine in steady state the kVAR power and the capacity required to correct the Total power factor to a value of 0.97 rear.
For this kind a problem, how do you know how the voltage source is configured ( wye or delta). The problem start getting the phase current for phase 1 and 2 , but do we have to pretend that voltage source to delta load is connected like y-delta to convert the voltage to delta source? Or how does it work?
A three-phase circuit is balanced. The source voltage for the a-phase has a magnitude of 100 volts, and you can assume the phase angle is a reference of 0 degrees. Write the phasor expressions with proper subscript notation for the source voltage for each leg of the three-phase source if it is in a positive phase sequence.
Draw three transformers for each of the different three-phase connections. That is, draw three transformers and then make the connection, eg star-star, then redraw three transformers and make another three-phase connection, and so on until all four combinations of three-phase connections are made.
Three load units A, B and C are connected in parallel and take currents that are respectively 12, 10 and 15 amperes. Assuming IA to be the reference phasor, IB leads IA by 30°, and IC lags IA by 65°, calculate the total current and the angle it makes with the reference.
Draw Wye- Delta three phase transformers connection ( no-load and full-load) in Lt-spice
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
Three single phase loads are connected to the 400 V, three phase lines, 60 Hz. Load 1 operating at 3 kVA, 0.8 power factor lagging and is connected at line "a" and "b", Load 2 is a 5 kW heater and is connected at line "b" and "c", Load 3 is 4.5 kW machine that operates at a power factor of 0.6 lagging and is connected at lines "c" and "a". a. What are the line currents Ia, Ib, and Ic in Amperes (in Polar form) b. What is the total real power in W. c. Total Reactive Power. d. Total Apparent Power. e. What is the total power factor.