A 3 m wide rectangular channel carries a flow of 6 m³/s. The depth of flow at a section P is 0.5 m. A flat-topped hump is to be placed at the downstream of the section P. Assume negligible energy loss between section P and hump, and consider g as 9.81 m/s². The maximum height of the hump (expressed in m) which will not change the depth of flow at section P is

A 3 m wide rectangular channel carries a flow of 6 m³/s. The depth of flow at a section P is 0.5 m. A flat-topped hump is to be placed at the downstream of the section P. Assume negligible energy loss between section P and hump, and consider g as 9.81 m/s². The maximum height of the hump (expressed in m) which will not change the depth of flow at section P is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 4: A pipeline x joins pipelines 1 1, 2 and 3 at junction A. The pipelines 1,2 and 3 merges at junction B to form a single pipeline y. The pressure heads at A and B are 78 m and 42 m, respectively. X A 2 В y Use Hazen-Williams constant c 120 for all pipes. Pipe Length 3,000 m 1,300 m 2,600 m Diameter 300 mm a. Compute the rate of flow in pipeline 1. 1 200 mm b. Compute the rate of flow in pipeline 2. 250 mm c. Compute the total rate of flow.
Consider the two reservoirs shown in figure, connected by a single pipe that changes diameter over its length. The surface of the two reservoirs have a difference in level of 9m. The pipe has a diameter of 200mm for the first 15m (trom A to C) then a diameter of 250mm for the remaining 45m (from C to B). For the entrance use KL=0.5 and the exit KL=1.0. The join at Cis sudden K-1.0. For both pipes use f=0.01. find Q. Enterence. pipe2. Dizmelor = Dz=250mm -Pipe1 Diameloe i Length=L2=D45m. D=20am leryth =4,=15m. 8 Exit- Iution
2. Three reservoirs A, B, and C are connected respectively with pipes 1, 2, and 3 joining at a common junction P. Reservoir A is at elevation 80 m, reservoir B at elevation 70 m and reservoir C is at elevation 60 m. The properties of each pipe are as follows: Pipe 1: L = 5000 m, D = 300 mm Pipe 2: L = 4000 m, D = 250 mm Pipe 3: L = 3500 m %3D The flow from reservoir A to junction P is 0.045 m3/s and f for all pipes is 0.018. (a) Find the elevation of the energy grade line at P in m (b) Determine the flow on pipe 2 in m3/s (c) Compute the diameter appropriate for pipe 3 in mm
Problem-4, A pipe of 0.7 m diameter has a length of 6 km and connects two reservoirs A and B. The water level in reservoir A is at an elevation 30 m above the water level in reservoir B. Halfway along the pipe line, there is a branch through which water can be supplied to a third reservoir C. The friction factor of the pipe is 0.024. The quantity of water discharged into reservoir C is 0.15 m³/s. Considering the acceleration due to gravity as 9.81 m/s² and neglecting minor losses, the discharge (in m³/s) into the reservoir B is
1- Uniform flow passes through a rectangular channel having a width of 4 m. The channel carriers a discharge of 12 m³/s with a depth of 3 m at section 1. The bed is raised in section 2 by 20 cm and the velocity distribution changes due to bed roughness. Note: The energy loss is 10% of the velocity head at section 2. Velocity profile in section 2 can be expressed by a linear equation as v ky2. a) Write the energy equation b) Calculate the flow depth at section 2 c) Calculate the Froude number at sections 1 and 2 of Side vehw Y/₂ Az
Q2] Water flows in a rectangular channel at a depth of 1.5 m. A 30 cm in height smooth hump produses a drop of 15 cm in the water surface elevation. Neglect losses and calculate the discharge per unit width of the channel. Energy line E₁ Y₁ 0.15 m V V₂ 1₂ Hump AZ=0.30 m 2
4.(b) A pipe ABC connecting two reservoirs is 80 mm in diameter. From A to B the pipe is horizontal as shown in the following figure, and from B to C it falls by 3.5 metres. The length AB and BC are 25 and 15 m respectively. If the water surface in the reservoir at A is 4 m above the centre line of the pipe and at C 1 m above the centre line of the pipe, calculate the quantity of flow and also the pressure head in the pipe at B. Neglect the loss at the bend but consider all other losses. Take Darcy f= 0.024. Draw the energy and hydraulic grade lines. 4 m A 3.5 m ↓ -Ba C t Ilm
1. A 1 meter diameter pipe 1400 m long has a discharge of 600 liters/ sec a. Compute the head loss using f = 0.018 b. Compute the head loss using n = 0.015 c. Compute the head loss using C = 100 %3D %3D %3D
Two tanks A and B have 80 m diffenence in water levels, and are connected by a pipe 0.3 m diameter and 8 km long with 0.002 friction coefficient. The pipe is tapped at its mid point to leak out 35 1/s flow rate. Determine the leaving tank А? discharge Find the discharge entering tank B? Coefficient (Tank Exit) = 0.5 %3D Coefficient (Tank Entry) = 1 %3D ha %3D A he 80 m Q1
2. The suction pipe of a pump rises at a slope of 3 vertical in 4 along the pipe which is 12 cm in diameter. The pipe is 7.2 m long; its lower end being just below the water surface in the reservoir. For design reasons, it is desirable that pressure at inlet to the pump Pump 4/3 shall fall to more than 75 kPa below atmospheric pressure. Neglecting friction, determine the maximum discharge that the pump may deliver. Take atmospheric Suction pipe pressure as 101.32 kPa. F.W.S. Reservoir/sump 2. 7.2 m
1.) SAE 10 oil at 20° (ρ=869 kg/m³, μ=8.14 × 10-2 N•s/m²) flows in a 200 mm diameter pipe. Find the maximum velocity for which the flow will be laminar.
A straight pipe AB, of length 10 m, tapers from a diameter of 40 cm at A to 20 cm at B. The centre line of the pipe is so located that the end B is 2 m above the level of A. Liquid of specific gravity 0.9 flows through the pipe at 150 litres/second. Pressure gauges connected at A and B show the readings of 60 kPa and 40 kPa, respectively, Determine the direction of flow.