A 240-V, 100 A armature full-load current, 1800 RPM, cumulatively-compounded DC motor is considered in this problem. Its characteristics are given below: RA+Rs = 0.20 $2 RF = 140 2 Radi = 160 2 NF-2000 turns NSE = 16 turns This motor has compensating windings and interpoles. The magnetization curve for this motor at 1800 RPM is shown in a tabular form below: If, A 0 0.1 0.2 0.4 0.5 0.6 0.8 1.0 1.2 1.6 1.8 2.0 2.2 2.4 EA.V 6.0 25 50 110 135 160 205 235 255 275 285 288 290 291 What is the full-load speed of this motor? Answers: Write the speed in the first box and the unit in the second box. The full-load speed is:

A 240-V, 100 A armature full-load current, 1800 RPM, cumulatively-compounded DC motor is considered in this problem. Its characteristics are given below: RA+Rs = 0.20 $2 RF = 140 2 Radi = 160 2 NF-2000 turns NSE = 16 turns This motor has compensating windings and interpoles. The magnetization curve for this motor at 1800 RPM is shown in a tabular form below: If, A 0 0.1 0.2 0.4 0.5 0.6 0.8 1.0 1.2 1.6 1.8 2.0 2.2 2.4 EA.V 6.0 25 50 110 135 160 205 235 255 275 285 288 290 291 What is the full-load speed of this motor? Answers: Write the speed in the first box and the unit in the second box. The full-load speed is:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A universal motor has armature circuit resistance of 15 ohm and inductanceof 0.3H. On being connected to a 220 V dc supply, it draws 1.5 A from themains and runs at 2000 rpm. Find the speed and power factor of the motor,when connected to a 230 V, 25 Hz supply and drawing the same armaturecurrent.
L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no
1- To control the speed of an induction motor, the supply frequency is reduced by 10%. For the same magnetizing current to remain constant, the supply voltage must be....... a) Reduced by 10%, b) Reduced by 20%, c) Increased by 10%, d) Increased by 20% 2. When maximum starting torqua ic ohtoinod
A value of magnetizing current in a 3-phase induction motor * gives power factor smaller .. larger smaller. .poor large . better O large...poor O
• Q5/ in a DC motor. List and describe the types of losses that occur
QUESTION 2 a) Draw the equivalent circuit and torque-speed characteristic curve for a series DC motor. b) Briefly explain the induced torque occurs in a series DC motor. e) A 20-hp 240-V 76-A 900 rimin series motor has a field winding of 33 turns per pole. Its armature resistance is 0.09 2, and its field resistance is 0.06 2. The magnetization curve expressed in terms of magnetomotive force versus Ex at 900 rimin is given by the following table: Table Q2 c): The magnetomotive force table for a de motor taken at 900r'min E. V 95 150 188 212 229 243 F.A tuus 1000 1500 2000 2500 500 3000 If the motor running at 33 percent of the full-koad armature current, determine: ) The motor's power converted from electrical to mechanical form, Prene i) The motor's torque, Tnit ii) The motor's speed, n
The relation between armature torque and armature current of a DC motor is Parabolic Linear Inverse Exponential
Design and develop equivalent circuit model of a single phase Induction motor with th consideration of core losses present with the parameter consideration of stator resistance R1 and reactance X1 and two rotor parameters which includes r2,x2 and magnetising reactance xm. (Illustration is required) Draw by hand please
The schematic and torque-speed characteristics of a series wound DC motor are shown below : Field winding DC Supply Eb speed Torque - T-K, I, Field Flux = ø = Kla (i) According to the equations given above, explain why the torque of the series-wound DC motor is so high at low speed. Give application examples that require such torque-speed characteristics. A series-wound DC motor should never be started with light or NO LOAD. Give reason. (ii) (iii) Armature anbio
A 35.2 HP, 250 V, 100 A, 1200 RPM, series DC motor with no armature reaction is considered in this problem. This motor has a series-field winding of 5 turns per pole. Its armature resistance in RA =0.05 ohm, and its series field resistance is Rs =0.05 ohm. The magnetizationcurve at 1200 RPM is given by the following table:
1. A fundamental DC motor is shown below. VTerminal = 90V. The running current, I = 5A and the rotor resistance, R = 4 ohms. Answer the following: CEMF or E at the running condition = , Power delivered by the source at the running condition = Power converted to mechanical power at the running condition Power lost in heat by the rotor resistance = Show your work for each calculation. Suggest that you clearly mark the schematic. frut
Sketch the torque versus speed characteristic for a series-connected dc motor.