A 24 ft column shown below, pinned at one end and fixed at the other, is used to suppor a compressive axial load. It has a bracing in the weak axis direction at 1/3 of the length from the pinned end. Select the lightest W 14 section that adequately support the loads PD-400 kips and PL-175 kips. Use A572 Grade 50 steel. /////// L *

A 24 ft column shown below, pinned at one end and fixed at the other, is used to suppor a compressive axial load. It has a bracing in the weak axis direction at 1/3 of the length from the pinned end. Select the lightest W 14 section that adequately support the loads PD-400 kips and PL-175 kips. Use A572 Grade 50 steel. /////// L *

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.5.13P

See similar textbooks

Similar questions

A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
The truss shown is composed of steel sections. If the 2L150 x 90 x 8 A36 steel section was used in member CG, is it satisfactory? Use 2 lines of 4-20mm fasteners spaced 75 mm on center for all joints. The loads applied in the truss are. service loads. Use ASD only. You can use ASEP Manual. Multiply the loads by 10. 50 kN 30 kN- 3 m G 3 m 3 m 30 kN- D 30 kN- A m E H m C
Question 4: A W12 x 65 of A572 Grade 60 steel is used as a compression member. It is 26 feet long, pinned at each end, and has additional support in the weak direction at a point 12 feet from the top. Can this member resist a service dead load of 180 kips and a service live load of 320 kips? a. Use LRFD. b. Use ASD.
ASSIGNMENT #5 BIAXIAL BENDING Problem: Check the beam shown for compliance with the NSCP Specification. Lateral support is provided only at the ends, and A992 steel is used, F, = 345 mPa. The 90 kN service loads are 30% dead load and 70% live load. a. Use LRFD b. Use ASD d tw by ty 1x(106) S(10³) mm mm mm mm³ mm mmª W410x100 415 10 260 16.9 398 1920 SECTION Tx mm 177 1m 90 kN 90 KN 1.5m W410x100 I Loaded Section Ly(106) Sy(10³) Ty mmª mm³ mm 49.5 381 62.4 1m Zx(10³) Zy(10³) mm³ mm³ 2130 581
Steel Designa. Say a W12x45 is not safe against rupture, what other design considerations should be explored to increase its capacity and thereby be safe for rupture.b. Say you are to design a tension member using a C-section and found out that no C-section is safe against yielding and rupture. As a designer, what would be your approach to this? Ans. is built up section, please do explain why build up section.
A W18 3 119 is used as a compression member with one end fixed and the other end pinned. The length is 12 feet. What is the available compressive strength if A992 steel is used? a. Use AISC Equation E3-2 or E3-3. Compute both the design strength for LRFD and the allowable strength for ASD. b. Use Table 4-14 from Part 4 of the Manual. Compute both the design strength for LRFD and the allowable strength for ASD.