A 230 V, single phase, watt hour meter has a constant load of 5A passing through it for 8 hours at unity power factor. If the meter constant is 460 revolutions per kWh, how many revolutions does the meter disc make during this period? If the same meter makes 1638 revolutions when operating at 230 V and a constant load of 6 A passing through it for certain duration at a power factor of 0.86, determine the duration of operation of the meter in hours.

A 230 V, single phase, watt hour meter has a constant load of 5A passing through it for 8 hours at unity power factor. If the meter constant is 460 revolutions per kWh, how many revolutions does the meter disc make during this period? If the same meter makes 1638 revolutions when operating at 230 V and a constant load of 6 A passing through it for certain duration at a power factor of 0.86, determine the duration of operation of the meter in hours.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The industrial load in Figure 7 consumes 110 kW at 0.88 of lagging. The ammeter reads 252 A rms. Determine the voltmeter reading. Zune (Ammeter Power supply voltage Industrial load Voltmeter Figure 7
A certain current lags the voltage by 36 electrical degrees. The voltage waveform is increasing positively at t = 0 and an instantaneous value of 0 volt. If the frequency is 25 Hz, calculate at what time the current will be zero for the second time. What is the value of the voltage at that time? Peak values are 350 V and 50 A.
Electrical engineering
Detailed answer please
One single phase energy meter operating on 230 V and 5 A for 5 hours makes 1940 revolutions. Meter constant in revolution is 400. The power factor of the load will be:
When a load of 750 W is connected, the disc of a single-phase energy meter rotates at 16 revolutions per minute. If the load is on for 6 hours, determine the % error of the meter. The meter constant is 1200 revolutions/kWh in percentage?
Activity 1: You are testing an electrical device which can be modelled by the figure shown below: 18 -j12 j6 8 -j10 i1 E1 12 13 E2 13 The above electric circuit can be characterized by the following equations: 1811 + j6(I1 – 2) + 4(I1 – I2) = 1020° -j121, + 8(12 – I3) + 20290° + 4(12 – 1) + j6(I2 – 1) = 0 -j1013 + 1313 – 20290° + 8(I3 - 12) = 0 1. Rearrange the above three equations. 2. Write the set of equations in matrix form (A.x = b) 3. Find the determinant of the resulted matrix (A).
With frequency f= 500 cycles/sec, what is the pure element in series with the R=25 ohms which causes the current to lags the voltage by 20 deg?
urgent please fast no need to explanation
Waveform Generator RED CLIP BLACK CLIP R1 C1 1kQ 100μF Figure 3: Breadboard circuit. GND 7. Measure the value of R1: 8. Measure the value of C1: Wave Gen Wave Gen GND GND + GND GND For High Level O For Low I Level τ: R1: R1 1kQ C1: R1 1kΩ 카 GND Figure 4: Circuit behaviour. The circuits in Figure 4 show the expected behaviour of the RC circuit. When the waveform voltage level is high, the capacitor charges through R1. When the waveform voltage is low, the capacitor discharges through resistor R1. It is important to note that the switches in Figure 4 do not exist inside the instrument. They are an analogy to the circuit behaviour. 6. Calculate the T for this circuit: 11 GND C1 100μF C1 100μF