A 220-V electric heater has two heating coils that can be switched such that either coil can be used independently or the two can be connected in series or parallel, yielding a total of four possible configurations. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Find the power dissipation of each of the other two possible arrangements. W and The powers dissipated by R₁ and R₂ are W, respectively.

A 220-V electric heater has two heating coils that can be switched such that either coil can be used independently or the two can be connected in series or parallel, yielding a total of four possible configurations. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Find the power dissipation of each of the other two possible arrangements. W and The powers dissipated by R₁ and R₂ are W, respectively.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

1) In a certain circuit battery is draining out 5 times more quickly than expected for normal operation what could be the possible cause for this and how did you conclude it. 2) Why AC current is preferred over DC current for high power electrical circuits. 3) Initial current across a capacitor connected across a DC source is huge and initial voltage is zero, explain why this is so. 4) Explain the working of AC generator in your own words. 5) In a Wheatstone bridge circuit a student connects a motor in place of galvanometer and is trying to find unknown resistance using formula when he adjusts variable resistor and observes that motor is no more rotating. Do you agree with his technique or not explain with reasoning. 6) What does a negative value of loop current indicates in Mesh Analysis and Method of Branch Currents, and also comment on if there a way to avoid this negative sign appearing for loop current's value.
Two coils are placed close to each other as shown in the figure. The coil on the left is connected to a battery and a switch, and the coil on the right is connected to a resistor.What is the direction of the current in the resistori. an instant after closing the switch?ii. after the switch has been closed for several seconds?iii. an instant after opening the switch?Choose your answers betweento. on the leftb. on the rightc. the current is zero.And clearly explain the reason for your answer.
In the circuit in Figure 2, the capacitor andThe circuit of resistance is defined as a load circuit.a) Find the average power dissipated by the load circuit?b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Interpreting the results obtained?c) In the circuit in Figure 2, with a resistance of 80 ohms 23?A coil of is connected in series. In this case,calculating transformer ratio () to optimize power delivery to the load? Obtainedinterpreting the result?d) Calculate the distributed load complex power and reactive power in the newly learned circuit?
Q2) Consider the circuit in Figure (3), and answer 3 branch only. a) What type of circuit is this? b) What is the total peak secondary voltage? c) Find the peak voltage across each half of the secondary. d) Sketch the voltage waveform across RL. 4:1 120 V rms RL 1.0 k2 D2 eelee
Answer the following. Use a detailed explanation. In clamping circuit, what is the value of the sum of the voltage output for the whole cycle? In DC power supply, what is the use of the first capacitor?
How temperature effect conductivity? Explain with the help of following equation. m e'n7'
THE POLARITY MARKINGS ON TWO WINDINGS MUST BE DETERMINED EXPERIMENTALLY. THE DEVICE FOR SUCH DETERMINATION IS SHOWN IN THE FIGURE BELOW. THAT THE TERMINAL CONNECTED TO THE POSITIVE TERMINAL OF THE BATTERY RESERVES THE POLARITY MARKING AS SHOWN IN THE FIGURE. WHEN THE SWITCH IS OPEN, THE DC VOLTMETER UNDERGOES A NEGATIVE DEFLECTION. WHERE ON THE CONNECTED WINDING SHOULD A POLARITY MARKING BE ATTACHED TO THE VOLTMETER? t = 0 R )cc VOLTIMETER VB- CHOOSE AN OPTION BELOW: A. POINT AT THE LOWER END OF THE INDUCTOR B. POINT AT THE TOP END OF THE INDUCTOR C. NONE OF THE OPTIONS D. A DOT AT THE TOP END AND BOTTOM END C E. THERE IS NO COUPLING BETWEEN THE INDUCTORS, SO IT IS NOT NECESSARY TO PLACE A DOT
Urgent please In the circuit shown in the figure, the RL load is connected to a 20 V source when switch K is in position 1; In this position, draw the waveforms of the welding voltage, the voltage at the R end, the voltage at the L end and the current 1.
Eлample (1) For the series-parallel arrangement shown in Figure below, find: a) The supply current. I ?. b) The current flowing through each resistor. c) The p.d. across each resistor. R3 2.50 40 Ri R4 RE I ? 200V
basic concepts of direct current and alternating current, and the main applications that each one has today.
In the circuit below, switch S is initially disconnected from points A and B. The switch is then connected to A. What is the current and voltage in the resistors and inductor: a) as soon as the switch is turned on b) long after the key is turned on. The switch is then suddenly disconnected from A and connected to B: c) What is the current in the resistors at that moment? d) What is the voltage in the inductor? e) After that moment, what is the total energy dissipated by the resistors?
A five-Ohm resistor is in series with a 0.001-Henry inductor and is supplied from a 10-V DC source. Solve for the current 2 milliseconds after the switch was turned on. a. 2.0000 Amperes b.1.9999 Amperes c.1.0001 Amperes d. 2.0001 Amperes