A 200mmx400mm rectangular beam has 5-20mm diameter rebar at the tension side and 2-20 diameter rebar at the compression side. Determine the design moment capacity of the beam in (kN-m). [Answer in 3 decimal places] Given: db(main bars)=20mm dbs(stirrups) 10mm concrete cover = 35mm fy = 420 MPa fc' = 35 MPa

A 200mmx400mm rectangular beam has 5-20mm diameter rebar at the tension side and 2-20 diameter rebar at the compression side. Determine the design moment capacity of the beam in (kN-m). [Answer in 3 decimal places] Given: db(main bars)=20mm dbs(stirrups) 10mm concrete cover = 35mm fy = 420 MPa fc' = 35 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer to the question in reinforced concrete
In a given T-Beam, flange width = 700 mm, slab thickness = 100 mm, web thickness = 350 mm, effective depth = 450 mm. It is singly reinforced at the bottom side (tension side) with As = 2775 sq. mm. Take fc' = 17.24 MPa, fy = 413.7 mm. a) Determine the value of compression block "a"
Qz- Find the, Critical load Pe using E=2x1ổ Pc Pery 4m
For the given properties of the beam below, determine the safest wy that the beam will carry. bf = 800mm bw = 500mm tf = 90mm d = 375mm d' = 100mm fc' = 34.5MPa fy = 400MPa As = 8-32mm bars The answer is kN/m bf + A, D +bw t f Wu A को + Pu 50 5m KN (Factored) load B +im+
1. A rectangular beam has b = 300mm, d = 500mm, As = 6 – 32mm diameter bars, fc' = 27.6 MPa, fy = 414 MPa. Calculate: a) depth of compression block, "a" b) fs c) + d) Mu
For the hollow beam. Calculate the design. capacity, As = 2040mm ² Fy = 420 Mpa,Fc=25Mpa,Asmin check is not required
Compute the total elongation of the tapered steel bar shown in Fig. 5 subject to an axial load P (= 80 kN). The bar is of constant thickness 12 mm and tappers from W¡ mm at left to w2 mm at the other end. Given E=200 GPa for steel. Values of w1 and w2 for different Roll numbers are stated in Table below. What axial stress exists at mid-length section? Last digit of W1 W2 Roll No. (mm) (mm) P P 1, 4, 7 2, 5, 8 40 120 50 140 12 m 3, 6, 9 & 0 60 160
The service load bending moments on a beam are 128 kip-ft for dead load and 107 kip-ft for live load. The beam is 12 in. wide, f'c is 3000 psi and fy is 60 ksi. Determine Mu. Mt. p. R. the depth of the beam and the As of tensile reinforcing required. How many no. 8 bars or No. 10 bars would have the required As?
C30 concrete, S420 Steel, h=600mm, b=800mm, hf=100mm, bw=300mm, d'=40mm, steel rebars top and bottom = 5Φ20
Question 29 The laminated beam, shown in cross section, is composed of ?ve 6- in. by 2-in. planks that are glued together. The beam carries a uniformly distributed load of intensity we over its 8-ft simply supported span. If the working stresses are 75 psi for shear in glue, 90 psi for shear in wood, and 8ø0 psi for bending in wood, + 6 in. 1. determine the maximum allowable value of we so that the shear stress in the wood is not exceeded. A. 900 lb/ft C. 833 lb/ft determine the maximum allowable value of we so that the shear B. 555 lb/ft D. NOTA 2. stress in the glue is not exceeded. A. 900 lb/ft C. 833 lb/ft B. 555 lb/ft D. NOTA 3. determine the maximum allowable value of we so that the bending stress in the wood is not exceeded. А. 900 lb/ft В. 555 lb/ft C. 833 lb/ft D. NOTA 5 @ 2 in. = 10 in. –
1.)Calculate the height of the neutral axis measured from the extreme compression fiber. 2.) Calculate the strength reduction factor for the given beam. 3.) Calculate the design moment for the given beam. Given b=9.25mm d=152.5mm d(prime)=32.5mm L=1.1m WsubD=6.25kn/m WsubL=8.25kn/m 4 25mm tension steel bars 4 12mm compression steelbars FsubC(prime)=28Mpa FsubY=420Mpa
Q.4. Compute the design shear strength of the beam cross section shown in the below figure with the shear reinforcement #3 U shaped stirrups@ 8-inch c/c. Take fc-4000psi, and fy=60,000 psi 2#4 #3 stirrups @8 in. h (inch) 4#9 b (inch) 3 in. V / 0 NOTE Student take the data given below in the table against their name. ID Name b(inch) 18 h (inch) 32