A 2.0 m x 2.0 m square pad footing will be placed in a normally consolidated clay soil to carry a column load Q. The depth of the footing is 1.0 m. The soil parameters are: c’= 0, ϕ’= 26º , γ =19 kN/m3 , and cu = 60 kN/m2 . Determine the maximum possible value for Q, considering short-term and long-term stability of the footing

A 2.0 m x 2.0 m square pad footing will be placed in a normally consolidated clay soil to carry a column load Q. The depth of the footing is 1.0 m. The soil parameters are: c’= 0, ϕ’= 26º , γ =19 kN/m3 , and cu = 60 kN/m2 . Determine the maximum possible value for Q, considering short-term and long-term stability of the footing

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Shallow Foundations: Ultimate Bearing Capacity

Section: Chapter Questions

Problem 6.17P: A 2.0 m 2.0 m square pad footing will be placed in a normally consolidated clay soil to carry a...

See similar textbooks

Similar questions

A circular footing with a 1.5 m diameter is to be constructed 1.22 m below the ground surface. The subsoil consists of a uniform deposit of dense soil having the following strength parameters: Angle of Friction = 250 Nc = 24.1 Nq = 13.1 Ny = 9.1 Cohesion = 48 kN/m2 Unit weight of soil = 20.12 kN/m2 The groundwater table is at a great depth and its effect can be ignored. Determine the following: a) Ultimate bearing Capacity of the soil
A 2.0 m 2.0 m square pad footing will be placed in a normally consolidated clay soil to carry a column load Q. The depth of the footing is 1.0 m. The soil parameters are: c = 0, = 26, = 19 kN/m3, and cu = 60 kN/m2. Determine the maximum possible value for Q, considering short-term and long-term stability of the footing.
A 2.0 m 2.0 m square pad footing will be placed in a normally consolidated clay soil to carry a column load Q. The depth of the footing is 1.0 m. The soil parameters are: c = 0, =26, = 19 kN/m3, cu = 60 kN/m2 (=0 condition). Determine the maximum possible value for Q, considering short-term and long-term stability of the footing.
A rectangular footing 3m x 2m exerts a pressure of 100kN/m2on a cohesive soil Es= 5x104 kN/m2and µ = 0.5. Estimate the immediatesettlement at the centre, assuming(a) the footing is flexible (b) the footing is rigid (ii) Write about influence of water table in determination of bearing capacity.
1. A 3m x 3m square footing is constructed at a depth of 2m in a 26m deep clay layer with following soil properties: ] =16.5kN/m³, Normally Consolidated Clay, e̟= 0.65, Cc = 0.25,s=0.5 and Es= 6.0 MN/m2. If there is a 1000kN structural load on the footing, calculate the consolidation settlement of the footing.
A square footing having a dimension of 4m has its bottom at a depth of 3.2m Trom the ground surface. The water table is located at an insignificant depth. FS=3 Properties of wet soil are as follows: Specific gravity, Gs = 2.7 Void ratio, e = 0.35 Degree of saturation = 70% Cohesion, c = 19 kPa Angle of internal friction = 26 degrees Assume general shear failure. Calculate the following: 1. Gross Ultimate Bearing Capacity of the footing using Terzaghi's assumption, kPa. 2. Net Allowable Bearing Capacity of the footing using Terzaghi's assumption, kPa. Capa
A square footing having a dimension of 4m has its bottom at a depth of 3.2m Trom the ground surface. The water table is located at an insignificant depth. FS=3 Properties of wet soil are as follows: Specific gravity, Gs = 2.7 Void ratio, e = 0.35 Degree of saturation = 70% Cohesion, c = 19 kPa Angle of internal friction = 26 degrees Assume general shear failure. Calculate the following: 1. Gross Ultimate Bearing Capacity of the footing using Terzaghi's assumption, kPa. 2. Net Allowable Bearing Capacity of the footing using Terzaghi's assumption, kPa.
A 2.0 m x 2.0 m square pad footing will be placed in a normally consolidated clay soil to carry a column load Q. The depth of the footing is 1.0 m. The soil parameters are: c’= 0, ϕ’= 26º, γ =19kN/m3 , and cu = 60 kN/m2. Determine the maximum possible value for Q, considering short-term and long-term stability of the footing.
3) A circular footing having a diameter of 1.2m has its bottom at a depth of 2.7m from the ground surface. Water table is located at a depth of 1.3m below the ground. Soil has the ff. properties. Dry unit weight = 18.1kn/cum Saturated unit weight = 19.3kn//cum C = 15.74kpa Angle of internal friction = 20deg %3D a) Assuming local shear failure, find ultimate bearing pressure using terzaghi's equation b) Det. Allowable bearing capacity using a factor of safety of 3. c) Find allowable load on footing.
A circular footing with a 1.5 m diameter is to be constructed 1.2 m below the ground surface. Thesubsoil consists of a uniform deposit of dense soil having the following strength parameters.Angle of internal friction = 25o, Nc = 24.1 ; Nq =13.1 ; N = 9.1Unconfined compressive strength = 96 kN/m2Unit weight of soil = 20.12 kN/m3The ground water table is at great depth and its effect can be ignored.a) Compute the Ultimate bearing capacity of the soil.b) Compute the gross allowable bearing capacity of the soil using a factor of safety of 3.c) Compute the allowable load the footing could carry
A rectangular footing 3m by 4m is founded 1.2m below the ground surface for which the unit weight of soil is 17.8kN/m3. The cohesion strength is 10kPa and the angle of internal friction is 20degrees. Under the condition of general failure, evaluate the contribution from the following to the ultimate soil bearing capacity in kPa. The ground water table is at a level that does not affect the unit weight of the soil. Use Terzaghi’s bearing capacity factor. For Ø=20degrees: Nc = 17.69, Nq = 7.44, Ny = 3.64. 23. Due to Cohesion Strength Due to soil overburden Due to footing dimension
A long footing 2 m wide is located in the level area at the top of a long, 45° slope where clay soils exist. The slope height is greater than the footing width. The soil unit weight is 17.5 kN/m3, and the cohesion shear strength is 65 kPa. The D/B ratio is 1, and the b/B ratio is also 1. What loading can be imposed onto the footing per meter of length (using a factor of safety of 3 with the bearing capacity equation appropriate for footings along the top of slopes)?