A 1m³ tank contains 2.841 kg of steam at 0.6 MPa. Determine the temperature of the steam, using(a) the ideal gas equation, (b) the van der Waals equation, and (c) the steam tables.Then, (d) calculate the compressibility factor.

Answered: Image /qna-images/answer/2e5b2edb-9c31-4c03-9170-83733b73fbf9.jpg

Answered: A 1m³ tank contains 2.841 kg of steam…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Methane at 11 MPa and 305 K is heated at constant pressure until its volume has increased by 80 percent. Determine the final temperature using the ideal gas equation of state and the compressibility factor. Which of these two results is more accurate?
The air in an automobile tire with a volume of 1.23 ft3 is at 72°F and 0.5 bar. Determine the amount of air that must be added to raise the pressure to the recommended value of 1 bar Assume the atmospheric to be 14.7 psia and the temperature and the volume to remain constant.
Determine the volume flow rate and the density of carbon dioxide at the inlet and the volume flow rate at the exit of the pipe using (a) the ideal-gas equation and (b) the generalized compressibility chart. Also, determine (c) the error involved in the first case.
Consider water (H2O) at 320C and 6 Mpa. Determine the error in the specific volume predicted by the ideal gas law relative to the actual value. The molar mass of H2O is 18.02 g/mol
Determine the specific volume of superheated water vapor at 15.65 MPa and 355.11 C, using the generalized compressibility chart. Assume that the compressibility factor is 0.65. Round off your answer to 4 decimal places. R = 0.4615 kPa·m3/kg·K Tcr = 647.1 K Pcr = 22.06 MPa
THERMOFLUID A frictionless piston-cylinder contains 3.30 kg of saturated water at 1 MPa. The water is expanded at constant pressure until its temperature rises to 270 °C. The image of the system and process are shown in Figure 3. Determine: iii) final state of water in cylinder after expansion process, and show your evidence.
A piston-cylinder containing steam at 700 kPa and 250o C undergoes a constant pressure process until the quality is 70%. Determine per kilogram (a) the work done, (b) the heat transferred, (c) ΔU and ΔH https://drive.google.com/file/d/1c10zZDS1XyLdDNKIHcz_rEUOnorHlDHg/view?usp=sharing used this steam table
R-134a at 1.4 MPa has a specific volume of 0.02000 m³/kg. Determine the temperature of the R-134a based on: (a) The tables of data, (b) The ideal gas equation of state, and (c) The generalized compressibility chart. (d) Compare the result in (b) to the result in (a) and determine the percentage error. (e) Compare the result in (c) to the results in (a) and determine the percentage error.
The specific volume of superheated water vapor at 0.6 MPa and 900°C is 0.90179 m³/kg in the steam tables, determine the specific volume also using : (a) The ideal-gas equation. ( (b) The generalized compressibility chart. (c) Can we consider the superheated vapor to behave as an ideal gas under the given temperature and pressure? Why? (
A real gas exists at 130 C and 1.2 MPa. It is known that the critical temperature and critical pressure of the gas is 374.2 k and 4.059 MPa. It is also know that the ideal gas constant (R) of the gas is 0.12 kPa-m/ S/kg-K. In the question that follows, select the answer that is closest to the true value. Use the compressibility factor (Z) to determine the specific volume in units of m/kg. ,3, Tuesday Dece mber 7 2021 5:52:58 DM CST
An isolated piston inside a rigid, isolated cylinder, closed at both ends, has two chambers; one containing a two-phase water mixture and one containing a two-phase mixture of R-134a. If the temperature inside the chamber containing water is 85.9°C, determine the temperature inside the other chamber. Assume mechanical equilibrium. Do you have enough data to calculate the quality in both cases? Justify your answer.
Methane at 10 MPa and 30 °C is heated at constant pressure to 110 °C. Using the compressibility chart, determine the change in the Methane's specific volume as a result of this heating.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A 1m³ tank contains 2.841 kg of steam at 0.6 MPa. Determine the temperature of the steam, using (a) the ideal gas equation, (b) the van der Waals equation, and (c) the steam tables. Then, (d) calculate the compressibility factor.