A 180-V, DC motor is connected as a cumulatively-compounded DC motor. Its characteristics are given below: RA=0.10 2 Rs = 0.05 2 RF = 125 2 Radj = 100 2 NF 1000 turns NSE= 10 turns IL, rated = 55 A Nm= 1800 RPM This motor has compensating windings and interpoles. When the motor is rotating at 1680 RPM, 180 V supply, 52 A armature current, the rotational losses are 933 Watt. What torque is induced by this motor? Select one: O a. Induced Torque = 54.5 N.m O b. uced Torque = 50.9 N.m C. Induced Torque = 45.6 N.m. d. None

A 180-V, DC motor is connected as a cumulatively-compounded DC motor. Its characteristics are given below: RA=0.10 2 Rs = 0.05 2 RF = 125 2 Radj = 100 2 NF 1000 turns NSE= 10 turns IL, rated = 55 A Nm= 1800 RPM This motor has compensating windings and interpoles. When the motor is rotating at 1680 RPM, 180 V supply, 52 A armature current, the rotational losses are 933 Watt. What torque is induced by this motor? Select one: O a. Induced Torque = 54.5 N.m O b. uced Torque = 50.9 N.m C. Induced Torque = 45.6 N.m. d. None

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(c) What are the principle characteristics of DC series motor and DC compound motor, and what are its uses?
a 20kw, 200v dc shunt motor has an electrical efficiency of 86% and an armature resistance of 0.25ohms what is the value of shunt field resistance in ohms
A 100V shunt motor is developing 6Hp while operating at an overall efficiency of 86%. The armature and shunt field resistances are 0.06Ω and 50Ω respectively. Determine the SPL.
Colve asap
A 180-V, DC motor is connected as a cumulatively-compounded DC motor. Its characteristics are given below: RA = 0.102 Rs = 0.05 2 RF = 125 2 Radi = = 100 2 NF 1000 tums NSE = 10 turns IL, rated 55 A nm= 1800 RPM This motor has compensating windings and interpoles. When the motor is rotating at 1680 RPM, 180 V supply, 54A armature current, the rotational losses are 1026 Watt. What is the efficiency of this motor? Select one: a. % Efficiency 94.2 % b. None OC. % Efficiency 74.5 % d. % Efficiency = 83.7 %
For a 1.8 degree, 2 phase bipolar stepper motor, steeping rate is 100 steps/seconds. The rotational speed of the motor in rpm is
For a particular application, a 4-phase stepper motor must be capable of stepping in 22.5° increments. How many poles must it have? What is the rotational speed in RPM, when the control unit of the motor supplies 200 pulses per second ? Select one: O a. P = 4 poles, and nm = 750 RPM O b. P = 6 poles, and nm = 666 RPM O c. None O d. P = 8 poles, and nm = 520 RPM Clear my choice
Question A dc series motor with a resistance between terminals of 1 0, runs at 800 rpm from a 200 V supply taking 15 A. If the speed is to be reduced to 475 rpm for the same supply voltage and current the additional series resistance to be inserted would be approximately
In order to get higher speed of Dc motor the ..... ....... voltage supply most be low back emf (Eb) most be high O frequency most be constant
A 3-phase, 48 kW, start-connected permanent magnet (PM) motor has a rated speed of 6600 rpm when supplied from a 110 Hz supply. The d-axis and q-axis inductances are La= 3.5mH and Lg= 4.7mH, respectively. The armature resistance and rotational losses are negligible. The motor operates without field weakening up to 6600 rpm, and a negative direct-axis current is imposed if the motor operates at speeds above 6600 rpm. The no-load terminal line-to-line voltage at 5000 rpm is 420 V (RMS). a. Determine the permanent magnet flux linkage. b. Calculate the rated phase current. c. Calculate the rated line to line voltage of the PM motor. с. d. At a speed of 7300 rpm, the PM motor operates in field weakening mode with a direct axis current of -30A and produces a torque of 30 Nm. Determine the per-phase current at this operating condition.