A 13 mm-diameter tensile specimen has a 50 mm gage length. The load corresponding to the 0.2 percent offset is 6800 kg and the maximum load is 1800 kg. Fracture occurs at 7300 kg. The diameter after fracture is 8 mm and the gage length at fracture is 65 mm. calculate the standard properties of the material from the tension test.

A 13 mm-diameter tensile specimen has a 50 mm gage length. The load corresponding to the 0.2 percent offset is 6800 kg and the maximum load is 1800 kg. Fracture occurs at 7300 kg. The diameter after fracture is 8 mm and the gage length at fracture is 65 mm. calculate the standard properties of the material from the tension test.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Specimen (Rebar) Original Length Length when it was clamped Diameter (mm) Internal Diameter (mm) External 1 300 mm 163mm 10 15.030 2 300 mm 180 mm 10.020 14.386 3 300 mm 197mm 9.40 15.028 Dimension of Specimen Specimen A0 P max Tensile strength Modulus of elasaticity Percent Elongation 1 474 N 179.381 2.776 MPa 19.76 MPa 13.4% 2 475 N 159.070 2.895 MPa 18.74 MPa 16.67% 3 485 N 179.381 2.706 MPa 20.058 Mpa 13.4% Result of testing Observation What is the possible discussion of these tablesP.S THIS IS NOT GRADED, ITS JUST EXAMPLES
A 11 in. inner diameter, 0.35 " wall thickness pipe is under a pressure of 2.5 ksi where strain gages installed along axial and circumferential directions register strains of 180 and 900 micro-strains (x10^-6), respectively. A) What is the Poisson's Ratio of this material and it's Elastic Modulus? B) In a uniaxial test, the pipe's material is observed to yield at a longitudinal strain of 0.1 in/in. Assuming a factor of safety of 2, the pipe can withstand impact energy of _______ lb - in per foot without suffering permanent deformation. C) If the pipe is depressurized and then subjected to a torque of 50 lblb - ft.ft., it will experience a shear strain of ________ rad.
A 11 in. inner diameter, 0.35 " wall thickness pipe is under a pressure of 2.5 ksi where strain gages installed along axial and circumferential directions register strains of 180 and 900 micro-strains (x10^-6), respectively. A) What is the Poisson's Ratio of this material and it's Elastic Modulus? B) In a uniaxial test, the pipe's material is observed to yield at a longitudinal strain of 0.1 in/in.in/in. Assuming a factor of safety of 2, the pipe can withstand impact energy of _______ lblb - in.in. per foot without suffering permanent deformation. C) If the pipe is depressurized and then subjected to a torque of 50 lblb - ft.ft., it will experience a shear strain of ________ rad.
2) The stress-strain diagram for an alloy specimen having an original diameter of 0.5 in. and a gage length of 2 in. is shown in the figure below. TENSILE STRESS (MPA) 450 400 350 300 250 200 150 100 50 Part A 0 0 STRESS VS. STRAIN 0.002 0.004 STRAIN 0.006 Determine the modulus of resilience. Show units. Part B Determine the modulus of elasticity of the material. Part C Estimate the Yield Strength of the material. 0.008 0.01
Asiacell l. ZA0 @ 团 / photo_2021-02-18_13-04... 200 stress 150 (MPa) 100 50 0.1 0-2 0.3 strain From the tensile stress -strain behavior for the brass specimen ,cP the diameter is 12-8 mm Calculat e the follouding :- 1- The Yield stress , 2-Modulus of elasticity. - The Tensile strength .
Q1: A specimen made from Titanium with diameter 4 mm subjected to force of 2500 N. The specimen extended by 0.422 mm. If the young modulus is 107 GPa. Find the gauge length of specimen.
A test specimen in a tensile test has a gage length of 2.0 in and an area = 0.5 in?. During the test the specimen yields under a load of 32,000 lb. The corresponding gage length = 2.0083 in. This is the 0.2 percent yield point. The maximum load of 60,000 lb is reached at a gage length = 2.60 in. Determine: (a) Yield strength (b) Modulus of elasticity (c) Tensile strength (d) If the specimen necked to an area = 0.25 in', determine the percent reduction in area
A tensile test was performed on a metal specimen with a diameter of 1/2 inch and a gage length (the length over which the elongation is meas- ured) of 4 inches. The data were plotted on a load-displacement graph, P vs. AL. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/AL = 1392 kips/in. What is the modulus of elasticity? BI
If the Young’s modulus and rigidity modulus of a material are 210GPa and 70GPa respectively, calculate the Poission’s ratio of that material. a. 0.111 b. 1.111 c. 0.500 d. 0.801
Given the stress strain curves of 4 samples containing different melanin compositions. The initial length of the models is 15 cm and their initial diameter is 10 mm. A. What is the modulus of elasticity of each of the curves? B. What will be the length of each material just before it breaks?
The following data are taken from a 20mm in diameter bar of length 250mm, the following results were recorded. Assume that the curve of the stress-strain diagram is linear from the origin to the first point. P (load in kN) 8(elongation in mm) 112 0.2 154 0.3 167 0.4 0.5 174 181 0.8 Determine the a. Stress at 187 kN load in MPa b. Strain at 167 kN load in mm/mm (expressed in scientific notation) c. Modulus of elasticity in MPa d. Modulus of resilience in N-mm/mm e. Modulus of toughness in N-mm/mm 234 oo OOO O0
Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 5 mm & Modulus of Elasticity 207 GPa. It is found that the specimen has undergone an extension of 1.2 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain-induced due to the load "F" on the specimen is 3 x 10-³. Solution Cross-sectional Area, A (in mm²) = Tensile Stress, (in N/mm²) = Tensile Load, (in N) = Length of the Specimen (in mm)