A 121 lb. weight is being help up by a block and tackle pulley system of 3 attached pulleys also attached to the weight and three attached pulleys hooked to the ceiling. If a rope is tied to a hook on the bottom set of pulleys, then strung through a 1st top pulley then 1st bottom pulley then-2nd top pulley-2nd bottom pulley-3rd top pulley-3rd bottom pulley, then rope held-up by a person. What is the tension in the rope?

Q: a) Find expressions for normal force, shear force and bending moment diagrams as functions of x…

A: The given solution is an example of using mechanical design to solve a problem requiring a frame,…

Q: A multi-rod mechanism is used to move paper rolls over the transmission line. Get a degree of…

A: Solution : It is a basic four-bar chain with four turning pairs. The degree of freedom is calculated…

Q: As illustrated, an 800 N-m couple is applied to the flywheel. The friction coefficient of the belt…

A: Answer: (a) TB is the larger tension. (b) The contact angle is 4.1888 radians (240°). (c) The ratio…

Q: Truss members are two-force members; they are either in tension or compression when the member force…

A: Given Statement :- Truss members are two-force members; they are either in tension or compression…

Q: Find the force generated by the deltoid (right arm) if: His arm length (d) is: 0.84 m The COG of the…

A: Arm Length d=0.84mCOG=37%Wa=7.9NWw=126NAngle=90°Insertion=0.17mAngle for line of pull=11°…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: 1. A moving company rigs a pulley system to lift a piano to a fourth floor balcony 44 feet from the…

A: Write the given data. Number of supporting pulley, ns=6Number of down pulley, nd=1Wpiano=1200…

Q: The larger and smaller pulleys of a chain block has 31 and 29 recesses respectively. If the…

A:

Q: A hydraulic jack is shown below, if one exerts a force F of 145N on the handle of the jack,…

A:

Q: Q/ Find the reaction forces at A and B, (A pin connection and B roller connection)? 120N/m 100N/m A…

A: Let reactions at hinge support A be:RAH in horizontal direction and RA in vertical directionReaction…

Q: (13%) Problem 5: A shop sign weighing msg hangs from one end of a uniform beam weighing mpg. A hinge…

A:

Q: The plank only turns about the pivot. So, the forces on the plank, the weights of F1 and F2 and of…

A: See-saw has one support at the centre to balance the forces on it. The given questions say the…

Q: Which of following  is not a Reactive forces in a free body diagram? a.   Structural members…

A: Reactive forces develop whenever there is a contact between two members

Q: 8.2 Explain what is meant by the four-bar chain.

A:

Q: A gardener uses a 60 N wheelbarrow to transport a 250 N bag of fertilizer. How strong should she be…

A: Given Data: The weight of the wheelbarrow is, W1=60 N. The weight of the fertilizer bag is, W2=250…

Q: You have been employed in a company that has designed the truss shown in Fig. Q 2. Find the forces…

A:

Q: Boom AC is pin-connected at A and supported by a cable attached at C. For the given load, applied at…

A:

Q: 350 mm 600 mm 400 mm 600 mm. 550 mm 400 mm 450 mm 1600 N A) Draw a free body diagram of the Rod. B)…

A:

Q: Determine the forces in a truss using the method of joints 12. The load carried by member GC is: A.…

A:

Q: The force in member CE (kips) is equal to: a. 5.2 k (Tension) b. 11.5 k (Tension) c. 5.2 k…

A: Above question is analysed by method of sections. 1.Calculate support reactions due to load applied…

Q: Question- Two closed coil springs of stuffiness s and 2s are arranged in series in one case and in…

A: Two closed coil springs of stiffness-s and 2s are arranged in series in one case and in parallel in…

Q: 1. Using the method of joints (no other method is acceptable), determine the reactions and the force…

A: GIVEN DATA- A PLANE TRUSS GIVEN WE HAVE TO FIND FORCES IN MEMBER

Q: BI,Cf, fg Q.2) For the truss shown in figure below, determine the forces in 1o00 M 2/E

A:

Q: hooks Gand H. 0.35 m

A:

Q: The diagram shows the free body diagram of a joint in a truss which is supporting a load, F. In the…

A:

Q: 4m 2m C 2m 2m 30 A 800 kg nonuniform boom, 6.0 m long, is loosely pinned at the pivot at P. A 600 kg…

A:

Q: 6 kip A C 4 ft F 4 kip 8 kip -3 ft--3 ft --3 ft - --3 ft -

A:

Q: A load that weighs 165kg and has an end to end length of 1.2m has to be lifted by a crane. We have…

A:

Q: Calculate the force in the cable CD if the wight of the traffic light is 20 N and e is 60° 15…

A:

Q: Ten (10) lines are strung between the blocks in a block-and-tackle system whose sheaves have an…

A:

Q: ft. B `4 ft 8 ft 3 ft A Figure 03.12(a)

A:

Q: Help!!! Answer this correctly!! Please

A: Step 1: Step 2: Step 3: Step 4:

Q: Find the forces at point A and B of the landing gear shown below. (Hint: First draw a free body…

A:

Q: Activity 2: The spring DB has an unstretched length of 2 m. • Discuss with your peers what is the…

A: To discuss: The expression that describe the forces of a spring, draw FBD, explain weight of the…

Q: The links in a truss are connected at their ends by pins. Select one: True False

A:

Q: A two-tier system to repair bridges is supported by two steel cables for each platform. Lengths of…

A: Given:- LA=55in LD=180in LC=180-55=125in Payload=160lb Stretch of cable, ∆l=0.01 To find: Diameter…

Q: I Review Fpc = 197 lbs Submit Previous Answers Learning Goal: To apply the method of sections to…

A:

Q: a. Draw the free body diagram for barrel A and B. Can you solve for the unknowns in the FBDs?…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.