A 10 kg block is placed on an inclined surface as shown in the figure below. Determine the maximum friction force and the block motion state. The static coefficient of friction between the block and the surface is 0.25. 10 kg 30

A 10 kg block is placed on an inclined surface as shown in the figure below. Determine the maximum friction force and the block motion state. The static coefficient of friction between the block and the surface is 0.25. 10 kg 30

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.22P: A 1.1-kg disk A is placed on the inclined surface. The coefficient of static friction between the...

See similar textbooks

Related questions

Q: Hot water at 400kPa, 150 deg Celsius is fed to a throttle at a rate of 1.5kg/s and exits at 200kPa. ...

A: Pressure(P1)= 400KPa Inlet Flow rate (m.1)= 1.5 kg/sec Pressure (P2)= 200 KPa

Q: Define CONNECTIONS WITH THE SUPERSTRUCTURE

A: Given data : Connection with the superstructure

Q: Q1: What is the density (g/ml) of a 3.6M Sulfuric acid solution that is 29% H,So, by mass (Mwt. = 98...

Q: clearance between the punch and the die should be

A: Given; A sheet metal with a stock hardness of=250 HRC It has to be shared using a punch and a die ha...

Q: A cube of side 5 cm is left in a furnace. If thermal diffusivity (a) is 21.9 × 10-6 m2/s then the Fo...

A: Given:L=5 cm =0.05 mα=21.9*10-6 m2/st=10 sec

Q: A heat pump absorbs 10 kW of heat from outside environment at 250 K While absorbing 15 kW of work. I...

A: As per given data, Heat absorbed from outside environment = Q1 = 10 kW Work done = W = 15 kW Heat ...

Q: A suppressed weir (C = 1.84) under a constant head of 90mm feeds a tank containing a 75 mm diameter ...

Q: A system executes a cycle during which there are three heat transfer Q12 = 200 kJ, Q23 = - 25 kJ, Q3...

Q: The homogeneous bar shown in Fig. P-106 is supported by a smooth pin at C and a cable that runs from...

Q: The number of units to be produced by the firm such that the profit

A: Given; Cost function for a product in a firm is given by= 5sqWhere, q= ampount of productionThe fi...

Q: A 257x 457.2 mm single acting engine runs at 200 rpm and makes 90 explosions per minute. The gross w...

Q: Using the parallel-axis theorem, determine the product of inertia of the glven area with respect to ...

A: The product of inertia of the given area with respect to the centroidal x and y axes is 901.334 in4.

Q: 9. Determine the smallest allowable cross-sectional areas of members BD, BE, and CE of the truss sho...

Q: B. 30°

A: Givenweight of the cylinder W=30+51=81Nθ=30oFCB=2FCA

Q: An open cylindrical tank 1.2 meters in diameter and 2.1 meters high is 2/3 full of water. After rota...

Q: f 9 m^3 of an ideal gas at 24 degC and 148 kPaa is compressed to 4 m^3. What would have been the pre...

A: Given:V1=9 m3T1=24 CP1=148 KPaV2=4 m3k=1.3

Q: A load is supported by four 304 stainless steel wires that are connected to the rigid member’s AB an...

Q: Determine the internal resultants FG, VG, and MG on the cross-section at G of the horizontal frame m...

Q: List down the ISO symbols and its corresponding quantity in the pneumatic circuit diagram below:

A: Explanation: There are total 5 symbols used in the given Pneumatic circuit. The corresponding number...

Q: For an ideal gas, a constant pressure line and a constant volume line intersect at a point, in the t...

A: Calculated the ratio of the slopes of the constant pressure and constant volume at the point of inte...

Q: Knowing that tanks exposed into the atmosphere have pressure of atm. What is the design pressure? a...

A: The tank design on basis of pressure can be done by three ways: Atmospheric pressure design Full va...

Q: Q10: Approximately what magnitude force, FM, must the extensor muscle in the upper arm exert on the ...

Q: 6. Determine the largest weight W that can be supported safely by the structure shown in the figure....

Q: (1 hr.) ,then cooling as the (TTT diagram) as below. find the final structure for each sample. 1- ra...

A: Solution is attached below:

Q: steel shaft 8 ft long that has a diameter of 3 inches is subjected to a torque of 27 kip ft. Determi...

Q: Determine the magnitude and direction of the resultant of the following forces: 50 N at 50 degrees,6...

Q: A high-strength steel bar used in a large cranehas a diameter d = 2.00 in. (see figure). The steel h...

Q: The distance between two parallel shafts is 20 mm and they are connected by an Oldham's coupling. Th...

Q: pordinate direction angles of the

A: finding the co-ordinate of points A0,0,6, B2,-3,0 And C 3,2,0 and( 2) calculating the position vecto...

Q: For steady, fully developed flow inside a straight pipe of diameter D, neglecting gravity effects, t...

A: Given data To select the correct option.

Q: intercooling pressure for minimum

A: Given; The compressor of a gas turbine plant, operating on an idealintercooled Brayton cycle accompl...

Q: Calculate the number of degree of freedom of the mechanism as shown in Fig. P. 1.15.15. 3 4 8

Q: anufacturing plant gave it a P100,000 o fabricate a machine part needed for e a

A: mechanics 's financial plan to manufacture a machine part required for their preventive upkeep progr...

Q: Cars A and B are traveling in adjacent highway lanes and at t = 0 s have the position and velocity s...

Q: ircular tube of aluminum is subjected to torsion by torques T applied at the ends (see figure). The ...

A: Given:L=27 indi=1.2 indo=1.6 inθ=3.157°T=51,662 in

Q: A glass manometer with oil as the working fluid is connected to an air duct as shown in the figure b...

A: According to the details provided in the question, we need to find the oil level in the pipe.

Q: A swimming pool is filled with 2 m of water. Its bottom is square and measures 4 m on a side. Two o...

A: Answer: The force of the water on (a) bottom: 313.92 kN (b) a vertical side: 99.11 kN (c) the 45° e...

Q: On a very cold day at the South Pole, the temperature of air is –60oF. Assuming that the air remains...

Q: 2. Find the Moment about A and B for the forces acting on the body shown below. The forces acting at...

Q: Part A ed by a smooth thrust bearing at A mearing at B. If P = 20 kN , determine the absolute maxi E...

A: Given data Force = 25kN Outer dia = 80mm Inner dia= 60 mm

Q: The rod OA rotates in the horizontal plane such that e = 0.72t radian, and collar B is sliding outwa...

Q: The probability that a randomly chosen shock absorber,

A: Given; An automobile plant contracted to buy shock absorbers from two suppliers X and Y.X supplies=...

Q: A centrifugal pump is delivering 0.04 m³/s to a height of 20 m through a 150 mm diameter and 100 m l...

A: Given Data: Q=0.04 m3/s ; Hd=20 m Pipe diameter, D=150 mm=0.15 m Length of pipe, l=100 m Suction lo...

Q: A wind turbine rotates at speed of 300 rpm. What is the circumferential velocity at the tip of the ...

A: GivenN=300rpmwind velocity V=7m/sTip speed ratio TSR =7m/s

Q: A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501...

A: mass flow rate (m.)= 200 kg/h= 200 kg/3600 sec= 0.0555 initial temperature ( Ti)= 501 C speed (C1)= ...

Q: 90 MPa 60 MPa 20 MPa

A: Given, Normal stress in x-direction = σx = -20 MPa Normal stress in y-direction = σy = 90 MPa Shear ...

Q: Using a double-acting cylinder a work piece is removed and tipped onto conveyor belt. The operation ...

A: Solution: The Pneumatic circuit Diagram with ISO symbols is shown below:

Q: Assume you are a Mechanical design engineer assigned to modify the available Laptop cooling pad in t...

A: given; In laptop cooling pad working principal ,method of cooling ,material involved some extra feat...

Q: ected to torsion by torques T applied at the ends (see figure). The bar is 10 in. long, and the insi...

Q: A steel shaft 7 ft long that has a diameter of 5 inches is subjected to a torque of 47 kip ft. Deter...

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

A 10 kg block is placed on an inclined surface as shown in the figure below. Determine the maximum
friction force and the block motion state. The static coefficient of friction between the block and the
surface is 0.25.
10 kg
30

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
A wedge is used to prop up the 6000-lb block of marble. The wedge angle is =30, and the angle of static friction is s=12 between all contact surfaces. Determine the smallest force P that would prevent the wedge from sliding out.
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
A 1.1-kg disk A is placed on the inclined surface. The coefficient of static friction between the disk and the surface is 0.35. Is the disk in equilibrium if P=5.5N and =30?
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.