A 1.5 m long column has a circular cross-section of 50 mm diameter. Consider Rankine's formula 1 for 1600 pinned ends and factor of safety of 3. If one end of the column is fixed and the other end is free, the safe load will be with values of f = 560 N/mm², a - (a) 9948 N (c) 9864 N (b) 9906 N (d) 9822 N

A 1.5 m long column has a circular cross-section of 50 mm diameter. Consider Rankine's formula 1 for 1600 pinned ends and factor of safety of 3. If one end of the column is fixed and the other end is free, the safe load will be with values of f = 560 N/mm², a - (a) 9948 N (c) 9864 N (b) 9906 N (d) 9822 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A flat brass bar has length L, constant thicknesst, and a rectangular cross section whose widthvaries linearly between b2 at the fixed support to b1at the free end (see figure). Assume that the taper ofthe bar is small. The bar has modulus of elasticity E.Calculate the displacements δB and δC if P = 200 kN,L = 2 m, t = 20 mm, b1 = 100 mm, b2 =115 mm,and E = 96 GPa.
А L B 425 mm C 1,000 mm V P A steel bar (1) and an Aluminum bar (2) are connected to a rigid angle ACD. Assuming: • Steel [E = 200 GPa] bar (1) is 6mm x 40mm x 600mm long. • Aluminum [E = 70 GPa] bar (2) is 10mm x 40mm x 600mm long. Poisson's ratio, v = 0.35 • A distance L of 500mm. a)Determine the force P (in kN) required to stretch the Aluminum bar by 1mm. Enter the force, P, into the d21 answer box (in kN, 3 sig digs). b) Determine the final width and thickness of the Aluminum bar. (1) Your Answer:
4 - A cantilever beam carries a tip load and moment applied at the tip, as shown in the figure. Find the stresses , and Cxy acting at points A, B and C. For each case, show those stress components on Mohr's circle of stress. dimensions in mm A B C. 20 40 260 JOKN 1 KN-m x [8⁰0 80 24 Cross-section
A rigid bar ABC is supported by three identical wires A, B, and C as shown in the figure. The bar ABC is horizontal before the load P is applied. Assume the bar and the wires are weightless. P 2a a A B . Determine the tension in wire B if P = 1200 N. O 700 N O 400 N 100 N O 600 N
Q-1 A compound bar consists of a circular rod of steel of diameter 25 mm, rigidly fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given, E = 2 × 105 N/mm² and Ecu 1.2 x 105 N/mm². = Steel tube → Copper tube '25mm 2.5mm
5. The column shown in the figure is reinforced with 8 28mm diam steel with fy = 414Mpa and f'c = 21Mpa (IS 456:2000) a. What is the nominal balanced load and balanced eccentricity? b. Fing pn if e = 220mm c. Find pn if e = 550mm d. Find pn when the stress in tension steel is 180Mpa 60 mm 550 mm 60 mm 650 mm e Pn
In figure shown we have: F b-3 in c=6 in d=3 in h=5/16 in Tall = 30 Kpsi Find force F.
The beam supports the loads as shown in the figure. Using E=200 GPa, w = 24 kN/m, P = 8 kN and M = 16 kNm, L1= 2 m, L2 = 6 m, L3= 2 m and a=30 mm. Find, b. by double integration method, the maximum EI8 between supports За a 8a B L2 L3 a 10a
An extruded beam has the cross section shown. It is given that V = 48 kN. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. D 10→ 0 I E 10 G -70 Dimensions in mm B 40 100 Determine the location of the shear center O. The value of e is mm.
Find the value q can take so that the BD bar, the cross section of which is shown in the figure, can carry the given load without buckling. factor of safety n = 3 Ri= 7cm , Rd=9cm on BD bar
90°–0 9. A A metal [E = 106 GPa; v = 0.31] bar of height h = 40 mm and thickness t = 8 mm is subjected to an axial load P. Two strain gages mounted at point A measure strains of ɛx = 575 µɛ and ɛy = -10 µɛ; however, the angle 0 indicated in the figure is not known. What is the magnitude of load P? Ex + Ɛy' : i με Ex + Ɛy = i Ox = i MPa P = i kN
1:55 PM A b a . 43 Quizzes DETERMINE FORCE (N) OF MEMBER EG in the truss shown. F1 = 219 N F2 = 539 N F3 = 444 N a = 34 degree x = 6 m. **Note: for compression, include a negative sign ( - ) and for tension, type your answer as is. Input your answer in two (2) decimal places only without the unit. В F a G F1 F2 F3 Dashboard Calendar To Do Notifications Inbox 因