A 1.00-in.-diameter solid steel shaft supports loads PA = 180 lb and Pc = 240 lb shown below. Assume L₁ = 5 in., L₂ = 16 in., and L3 = 8 in. The bearing at B can be idealized as a roller support and the bearing at D can be idealized as a pin support. Determine the magnitude and location of the maximum bending stress in the shaft. 4₁ B L₂ PC L3

A 1.00-in.-diameter solid steel shaft supports loads PA = 180 lb and Pc = 240 lb shown below. Assume L₁ = 5 in., L₂ = 16 in., and L3 = 8 in. The bearing at B can be idealized as a roller support and the bearing at D can be idealized as a pin support. Determine the magnitude and location of the maximum bending stress in the shaft. 4₁ B L₂ PC L3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A solid steel shaft supports loads PA = 500 N and PD = 580 N, as shown. Assume L1= 230 mm, L2 = 410 mm, and L3 = 350 mm. The bearing at B can be idealized as a roller support and the bearing at C can be idealized as a pin support. If the allowable bending stress is 22 MPa, determine the minimum diameterd that can be used for the shaft. D B L1 L2 L3 Pp PA Answer: d = i mm. Attempts: 0 of 1 used Submit Answer Save for Later
The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G = 39 GPa). Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm, determine the angle of twist at A. 60 mm TB = 1600 N-m 36 mm TA = 800 N·m A 400 mm B 375 mm --- 250 mm Then, determine the maximum and minimum shearing stress in shaft CD.
Prob 1. The rigid bar below is supported by a pin and two rods and must support a load of 100 kN is placed 3 m from A. The brass (Ebrass = 85 GPa) rod has a cross section of 30 x 30 mm and the copper (Ecopper = 120 GPa) rod 20 x 20 mm. Determine the normal stress and deflection of both bars. 1.5 m 2 m B -copper 100 kN brass- 3m 3 m E
A solid 1.00 in. diameter shaft is subjected to a torque of T = 240 lb-ft and an axial load of P = 5000 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = i Op2 = i Tmax in-plane A i H (1) 요. 요.. psi psi T B psi P X (b) Show the stresses of part (a) and their directions on an appropriate sketch.
Consider the loads of the figure to be axially applied at sections B, C, and D to the concrete structure supported at A. IW E F P G 5 kN 5 kN A Determine P in kN when member BC is 24 mm in diameter, the axial stress in section F is 588 MPa, and W 309822 N. = 10 kN C 10 kN Rigid -bearing plates
A solid steel shaft supports loads PA = 570 N and PD = 430 N, as shown. Assume L1 = 250 mm, L2 = 510 mm, and L3 = 230 mm. The bearing at B can be idealized as a roller support and the bearing at C can be idealized as a pin support. If the allowable bending stress is 38 MPa, determine the minimum diameter d that can be used for the shaft.
The splined ends and gears attached to the A-36 steel shaft are subjected to the torques shown. Determine the angle of twist of end B relative to end A, and the maximum shear stress in the shaft. The shaft has a diameter of 40 mm. GFe = 75 GPa. answer (maximum shear stress 31.8 MPa , torsion angle 0.01008 rad)
The assembly consists of two posts AD and CF made of A-36 Steel (E= 200GPa) and having a cross-sectional area of 1000m^2 and a 2014-T6 aluminum (E=73.1GPa) post BE having a cross-sectional area of 1,500m^2. If a central load of 400KN is applied to the rigid cap, determine the normal stress in each post. There is a small gap of 0.10mm between the post BE and the rigid member ABC.
A solid 1.10 in. diameter shaft is subjected to a torque of T = 390 lb-ft and an axial load of P = 4900 lb. (a) Determine the principal stresses and the maximum shear stress at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. Answer: (a) Op1 = op2 = i 20675.03 i Tmax in-plane -15518.77 18096.90 H psi psi psi T B P x (b) Show the stresses of part (a) and their directions on an appropriate sketch.
A horizontal rigid bar ADB of length 3m is pinned to a support at A and held by an inclined wire CD and vertical wire BE. The wires CD and BE are made of steel with diameter of 10 mm and 15 mm, respectively. Determine P if the allowable normal stress for CD and BE is 250 MPa Show complete solution. Thanks
The pin support A and roller support B of the bridge truss are supported on concrete abutments. The bearing failure stress of the concrete is (fail)b = 4 ksi. Apply a factor of safety of 2 against failure. (Figure 1) 150 kip 100 kip 1,) Determine the required minimum dimension of the square bearing plate at C 2.) Determine the required minimum dimension of the square bearing plate at D 200 kip 300 kip 300 kip 300 kip 300 kip -6 ft--6 ft--6 ft--6 ft--6 ft--6 ft--
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 15 mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120 MPa and its angle of twist is limited to 5°. Use G = 80 GPa for steel. (Note: Two values of P are to be compared here). 300 mm P. B 500 mm A