Answered: A 1 in diameter rod decreases in length…

A 1 in diameter rod decreases in length by 0.001 inches when subjected to a 4,893 kip load. If the rod is 4 ft long, what is the strain in the rod? Type your answer...

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A bridge member with a 5/8 inch diameter stainless steel rod supports a tension load of 6,000…

A: Diameter of stainless steel rod (d) = 56 inch Tension Load on Rod = 6000 pounds

Q: What is the maximum torsional stress in a 0.9 inch metal shaft with an applied torque of 18 k-in?…

Q: A 58 kN compressive load is applied to a 7 em diameter, 2 cm tall aluminium cylinder. Calculate…

A: Solution:- Stress:- The force per unit area, or intensity of the forces distributed over a given…

Q: A reinforced concrete column that is 10 m long is applied a comprehensive force. Under this force,…

A: Strain is defined as change in length by original length Unit strain is calculated in the below tab…

Q: A hollow steel tube with an inside diameter of 80 mm must carry an axial tensile load of 330 KN.…

Q: A 50cm long rod of 20mm diameter is facing 100N compressive load. If the Poisson’s ratio is 0.85 and…

A: Given data : Initial length (L)=50 cmFinal length (L')=40 cmInitial diameter (d)=20 mmForce (F)=100…

Q: A rod of cross-sectional area 100 m2 and length 5000 mm is subjected to a sudden load of 100 kN and…

A: Given, Cross section area of rod = A = 100m² Length of the rod = L = 5000mm P = 100kN Young modulus…

Q: A rod of cross-sectional area 100 m² and length 5000 mm is subjected to a sudden load of 100 kN and…

A: Given Data Cross sectional area (A) = 100 m2 Length (L) = 5000 mm Sudden load (P) = 100 KN Young…

Q: Figure P- 4.5 ft 1.5 ft 1.5 ft A 2.5 ft + 3.5 ft Part B Determine the maximum force P that can be…

Q: One shaft is in torsion as shown below. If the magnitude of shear stress at point A is 338.3 MPa,…

A: Given: Shear stress at point AζA=338.3 MPa. From the figure, Distance of point A from the…

Q: eam, 80 mm wi nly from zero at

Q: pipe thickness of the cylinder is 10 mm. Calculate the diameter of the pipe if the maximum stress…

Q: rind the minimum diameter of a steel wire, which is used to raise a load of 4000 N if the stress in…

A: Given data : Load (P)=4000 NStress (σ)=95 MN/m2Stress is defined as the force per unit area . Stress…

Q: A hollow aluminum circular cylinder, 32 cm tall with a 5.0 cm outside diameter and a wall thickness…

Q: 5/5 find the normal stress at left of point B A 100 D 40 KN S0 kN 40 mm 70 10 N 20 mm 30 mm 300 mm…

Q: A circular pipe of length 1 m, internal diameter 40mm and external diameter 50mm, is subjected to an…

A: Given data : The value of axial load (P)=100 KN The value external diameter (dO)=50 mm The value…

Q: A hollow aluminum circular cylinder, 32 cm tall with a 5.0 cm outside diameter and a wall thickness…

A: Step 1

Q: Loading on the roof of a bullding is unexpectedly 7000 pounds. The roof's dimensions are 5ft x 5ft.…

A: Given that dimensions of the roof = 5ft*5ft Allowable stress on the roof = 200psf Loading on roof…

Q: A seamless pipe is to carry a fluid under a pressure of 2 N/mm². The thickness of the cylinder is 10…

A: Given data: Pressure, P=2 Nmm2 Maximum stress, σh=100 Nmm2 Thickness, t=10 mm Diameter, d =?

Q: reliability

A: Using Formulaσp=σm+z(SD)here σm=170mpaSD=20mpa

Q: // If the value of the highest load we get from a tensile test of a wrought iron model with a cular…

Q: An 18-ft high column shortens by 0.4 in. under a load. What is the resulting strain in the column?

A: Given, L = 18 ft δL = -0.4 in

Q: 4.5 ft 1515ft T 2.5 ft 3.5 ft Part B occurs Determine the maximum force P that can be applied…

A: Given: Crate load = 330 lb Coefficient of static friction, μs=0.45 Tipping also occurs To find: The…

Q: A cantilever beam, 90 mm wide by 220 mm high and 8 m long, carries a load that varies uniformly from…

Q: Tension specimens (diameter d0 0.500 in., gage length L0 2.00 in.) made of structural materials A…

A: Given, Do = 0.5 in Lo = 2 in

Q: A circular column of diameter 100mm and of height 2m is subjected to a vertical load of 200 kN and a…

A: Given data- A circular column, Diameter d=100 mm, Height h=2 m, Vertical load P=200 kN, To Find- The…

Q: A common bar suspended has an axial load of 10000 lb, it has a cross sectional area of 20 sq. in.…

Q: a 50 m tape weighing 0.143 slug has a standard pull of 5.5 kg. the tapes cross sectional area and…

Q: A force of 250 N is applied to one end of a 14 inches diameter circular rod. Determine the value of…

Q: 3. A 1.5 ton crate is hoisted by three steel wires. Each wire is %4" in diameter and each carries…

A: Reference : Strength of material, Stress in cable. Given : Diameter of wire, Total weight of crate.…

Q: ello What is the difference between structures 1 and 2 under the same load? In fact, the question…

A: Rigidity is nothing but the ability of material of an object to resist the shear force i.e. how much…

Q: Describe about the strain-controlled test.

A: In testing a material we can have 2 approach i.e. strain controlled and stress controlled.

Q: int load • Line load

A: solution of above question is below:

Q: Cannot figure this problem out

A: Elongation due to external loading is given by,∆=PLAEwhere, P=applied load,L=length of…

Q: A ductile material is subjected to a tensile test. The yield strength was determined to be 100 MPa.…

Q: A cantilever beam, 80 mm wide by 260 mm high and 8 m long, carries a load that varies uniformly from…

Q: A wite with circular base of radius 3 mm was subjected to tensile stress of 13.5 Pa. if half the…

A: Stress in the circular base wire = 13.5 Pa stress to be applied in the square base wire=half of the…

Q: XN W = 200 N Hy = 0,3 1. Determine the normal force between the crate and the surface 2. Determine…

Q: A 1 in diameter rod decreases in length by 0.007 inches when subjected to a 2,571 kip load. If the…

Q: Consider a column which is subjected to a compressive load. A probable failure will be by buckling.…

A: A column which is subjected to a compressive load. A probable failure will be by buckling.We have to…

Q: Two semi-spherical thin-walled vessels are joined together by attaching 40-mm bolts around the…

Concept explainers

Pressure and Stress

Question

A 1 in diameter rod decreases in length by 0.001 inches when subjected to a 4,893 kip load. If the rod is 4 ft long, what is the strain in the rod?
Type your answer...

Expert Solution

Step 1: State the given data

Diameter of the rod (d) = 1in.

Decreases length of the rod (∆L) = 0.001 in.

Load (P) = 4893 Kips

Rod length (L) = 4ft

Determine the strain in the rod.

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

SHOW COMPLETE SOLUTION AND SKETCH THE ILLUSTRATION
A piece of wire 10-in long is tied vertically. The wire has a diameter of 0.1-in and is used to support a load of 100-lb. What is the stress developed within the wire? 1.
sir your help is highly appreciated. thanks
What is the torque, if a shaft of 200 mm diameter can transmit safely and the shear stress is not to exceed 50 N/mm²?
Please answer quickly
A 2500 lb horizontal bar is supported by three 3/16-inch diameter wires as shown. The wires are symmetrically spaced and 20 feet long. The two outer wires are steel and the middle wire is brass. Calculate: a) Stresses in the wires
what is the loading in pounds that you need to achieve vertical stress of 15 psi? Assume all the loading will put on the one-to-one ratio hanger. Assume a diameter of 2.5in.
A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is subjected to an internal pressure equal to the IMEP from item 1. Express your answers in MPa (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the internal pressure be increased if the stress in the steel is limited to 120 MN/m2?
Determine how many 18mm bolts should be used to attach a cap to a cylindrical tank with a diameter of 3.5m and a wall thickness of 16mm that is limited to a normal stress of 150MPa and the allowable stress for the bolt is 295MPa.
Please explain step by step so I can understand, the answer should be 112.5
Please answer complete question