A 0.26 m 30° 0.5 m 0.5 m 30 0.15 m 300 N Prob. 5-35

Q: Q2 a 90° bend reducing section, which connects to a 15-cm-diameter vertical pipe. The inlet of the…

A: Draw the control volume,

Q: Q13) For the best hydraulic section of a trapezoidal shape, if d = 1.0m, Z=1.0, the wetted perimeter…

A:

Q: C. Three cylinders are piled in a rectangular ditch as shown. R, = 5cm, R2 = 6 cm, R3 = 5 cm. W, =…

A: Reactions at A, B and C are :

Q: ( 3 cm ) in diameter and has a slope of ( 30° ) with the horizontal. The pressure gradient along the…

A: Given data

Q: Calculate the shear stress for the illustrated flow to 2 significant figures(dyn/cm2 ; do not use…

A: Given Data: Velocity Vo=7 cm/s. Velocity V=0. Distance d=30 mm. Viscosity of liquid is μ=2…

Q: A circular door having a diam. of 3m closes a horizontal duct from a small diam. as shown. The…

A:

Q: An isosceles triangle inclined 30 degrees with the horizontal with its top base 2.5m deep from the…

A: To find a) The force acting on one side of the gate. b) The pressure acting on one side of the gate.…

Q: Water Table 10 Cracked Tunnel Lining S. 4. +2 Impermeable Boundary A flow net is shown for a…

A:

Q: 1. Find the hörizontal force of the water on the horizontal bend shown below. V, - 30 fus 3 in. dia.

A: Given data  Velocity  Diameter of 1 pipe  Diameter of 2 pipe. We will solve it using momentum…

Q: • Find: External reactions in x and y directions needed to hold fixed vane. F,+ • Solution: OIS =…

A:

Q: For downward real flow in offset water pipe shown, find: The required pressure at D 1. 2. Determine…

A: Given, PA = 50 kPa L = 8 m  D = 20 mm or 0.02 m  Q = 0.2 L/s or 0.0002 m3/s

Q: Check the hydraulic structure shown below against piping and then find the thickness of floor at…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: From the given shear diagram below, where is the point of inflection located from the right end in…

A: From given SFD - Shear Force Diagram ; we can draw Load diagram ; The load diagram image is attached…

Q: Consider the steady open channel flow of water in the smooth constriction shown in plan view in…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: • Find: External reactions in x and y directions needed to hold fixed vane. F,+ • Solution: OTS =…

A:

Q: The inclined circular (D = 3,57 m.) gate shown below retains a liquid with SG = 3.64 on one side.…

A: Calculate the depth of centre of pressure from the free water surface. Then calculate the pressure…

Q: The section of the masonry dam is as shown in the figure. The specific weight of the fluid is 9.10…

A: Given Data:Masonry Damspecific weight of fluid=9.10kN/m3specific weight of concrete =…

Q: Question 4. The flowrate of the flow is 0,2c m³/s in a pipe placed on a horizontal plane. The pipe…

A: Given Q= 0.2 m3/s D1=0.4m D2=0.8m P1=80 kN/m2   Fx=force component in x direction Fy=force component…

Q: 5.81 The cross section of a concrete dam is as shown. For a 1-m-wide dam section determine (a) the…

A:

Q: Find: External reactions in x and y directions needed to hold fixed vane. F,t Solution: OS = 0.90)…

A:

Q: the inclined circular (D = 4.06 m) gate shown below retains a liquid with Sg = 3.35 on one side. the…

A: Given:-  Diameter of circular gate, D = 4.06 m  Specific gravity of liquid= 3.35  Theta = 39°  h=…

Q: An isosceles triangle inclined 30 degrees with the horizontal with its top base 2.5 m deep from the…

A: Hydrostatic force: The pressure acting on the fluid at rest influence of gravity is known as…

Q: 2.40 m/s. Find the total thrust components on the bend 17. A bend in a pipe gradually reduces from…

A:

Q: PROBLEM 2: The 280-kg, 6m-wide rectangular gate shown is hinged at B and leans against the floor at…

A:

Q: Problem 6. The 1.2 m - diameter log with specific gravity of 0.8 is 3.0 m long into the paper. The…

A:

Q: 1. What is the pressure at the center of pipe B? -y = 10 kN/m3 7= 20 kN/m3 50 cm 50 cm 10 cm

A:

Q: Problem 6. The 1.2 m - diameter log with specific gravity of 0.8 is 3.0 m long into the paper. The…

A:

Q: A rectangular plane, 1.2 m by 1.8 m is submerged in water and makes qn angle of 30° with the…

A:

Q: liquid 1 liquid 2 h3 h1 h2

A:

Q: 1- Structures are named as hydraulic structures must be fully submerged in water? a. True b. false

A: Given data Structures Water related problem  Fully submerged case.

Q: A 140 k and force with a slope of 4 vertical and seven horizontal is located on the second water and…

A: Given,  Force, F= 140k Horizontal= 7 Vertical= 4

Q: Find: External reactions in x and y directions needed to hold fixed vane. Solution: OS = 0.90). 30…

A:

Q: Water flows in the bend shown in figure at a rate of 5 m3/s, and the pressure at the inlet is 650…

A: To solve this problem, we will use Bernoulli equation. Therefore, we will calculate all the terms…

Q: Q3) Circular-arc Tainter gate ABC pivots about point O. For the position shown, determine (a) the…

A:

Q: Liquid 1 Liquid 2 h3 h1 h2

A: To find the pressure at the center of pipe using a manometer , we need to take a datum about which…

Q: Find the horizontal displacement at the roller. 15 kN/m C D E 6 m 9 m 25 kN 12 kN/m B A 12 m 5 m

A:

Q: Determine the moment of inertia of the cross-sectional area of the reinforced channel about the…

A: To determine the moment of inertia of the given cross-sectional area about the x-axis. In order to…

Q: The bin is 2 m wide and is filled with oil to the depth shown. Determine the resultant force acting…

A:

Q: 1. From the figure shown. Hinge 6'- PA 1/3(6)=2 6' B Py A. Compute the horizontal component of the…

A:

Q: For a 2.0 m wide and 0.40 m thick beam on elastic founda- tion, determine the coefficient of…

A: Solution : We know that, k=0.65EsB4EFIF 12  EsB1-μs2 Where, Es=Modulus of elasticity of soil B =…

Q: The pipe shown has a 180° horizontal bend in it as shown, and D is 20 cm. The discharge of water (p…

A: There are two forces due to pressure and the reaction force component in x-direction and weight and…

Q: Water flows through the pipe at A at 64 kg/s, and then out of B with a velocity of 4 m/s, as shown…

A: Flow rate can be distinguished by varying its velocity and the area of fluid that is flowing through…

Q: a) 135 kN b) 180 kN 9. The walls in the rectangular tanks are designed for a) bending b) tension c)…

A: Hi! Thank you for the question As per the honor code, We’ll answer one question since the exact one…

Q: Ex: By Bligh's and Lane's theory For the hydraulic structures shown below calculate : 1- Sketch the…

A:

Q: Question 4. The flowrate of the flow is 0,20 m²/s in a pipe placed on a horizontal plane. The pipe…

A: Solution Given Data Flow Rate Q=0.20 m3/s Pipe Diameter D1= 0.41 m Pipe Diameter D2=0.28 m Gauge…

Q: The subr ged sector gate AB Shown in tne igure below is one-sixtri of radius 8770 cm. The length of…

A:

Q: Trapezoidal section Q=120 m³/s S = 12 cm/km, Side slope 2:1, n=0.0182 Compare the dimensions for two…

A: Answer : (1) Let us first calculate the dimensions using the given data for the trapezoidal section…

Q: A quarter circular gate BP with radius of 3 m By is shown. The bottom of the gate is submerged depth…

A: Given specific gravity of liquid is 0.8

Q: 6.12. A 100 mm by 50 mm 180° pipe bend lies in a horizontal plane. Find the horizontal force of the…

A:

Q: 2. Hydraulic gradient line takes into consideration a) potential and kinetic heads only b) potential…

A: The hydraulic gradient line: It's the line that shows the pressure head (p/w) of a flowing fluid in…

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?