_21. In order to effectively perform dynamic and in-circuit testing of equipment, testing electroniccomponents is essential Which of the following electronic components lightsup when current flowsthrough it?a. Capacitorb. Fuse_22. Computers are electrically operated. Which of the following regulates the amount of currentflowing in an electronic circuit?а. Сарасitorb. ICc. LEDd. Resistorc. Inductorsd. Resistor_23. It takes good tools to perform good testing. What testing tools are capable of executing testsreporting outcomes, and comparing results with earlier test runs?c. Inspectiond. Platform testinga. Automatedb. Debugging24. There are several types of testing done when checking computer systems. Which of the followingis also knows as Validation?a. Dynamic testingb. In-circuit testing_25. There are components that require an extemal source to their operation, and there are thosewhich do not. What do you call those devices or components that do not require an extemal source totheir operation?c. Physical testingd. Static testinga. Active devicesb. Electrical devicesc. Electronic componentsd. Passive devices

Note : Since there are multiple questions, as per guidelines we can give solution to first question,…

_21. In order to effectively perform dynamic and in-circuit testing of equipment, testing electronic components is essential. Which of the following electronic components lights up when current flows through it? а. Сараcitor b. Fuse c. LED d. Resistor

_21. In order to effectively perform dynamic and in-circuit testing of equipment, testing electronic components is essential. Which of the following electronic components lights up when current flows through it? а. Сараcitor b. Fuse c. LED d. Resistor

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Tripling the voltage applied across an ohmic rod will A. make the protons move three time faster. B. reduce the resistance by one third. C. triple the resistance. D. reduce the current by one third. E. triple the current.
a. Bulb A remains the same because the voltage and current to it will be the same as before. b. Bulb A will glow brighter than before because adding another bulb in parallel will give greater current to bulb A, therefore greater brightness. c. Bulb A will glow lesser because adding another bulb in parallel will give lesser current to Bulb A, therefore lesser brightness. d. Either C or D e. Either B or C 2.In series circuit electrons in the current when comes to second bulb after passing through the first, have A. more energy B. No answer C. less power D. more power E. less energy
1. In each set of graphs below, the graphs go together and represent the Voltage and Current as a function of time for an R-C Circuit. For each set, determine whether the pair of graphs represents a charging circuit or a discharging circuit, and circle the correct answer. Also determine whether the vertical axis of each graph is for voltage or current and circle the correct answer. (a). Charging OR Discharging? (b). Charging OR Discharging? V(1) OR 1()? V(t) OR KO) ? t (sec) t (sec) V(t) OR 1(1)? V() OR 10)? t (sec) t (sec)
6. Which of the following would have an effect on the resistance of a conducting wire? A. The emf of the battery to which the resistor is connected B. The current passing the through the conductor C. The manner in which it is connected to other resistors D. The material from which the wire is made.
Which of the following factors will, if increased, make it more difficult to produce a certain amount of current in a conductor? D. the average time between collisions for a typical moving charged particle. C. the amount of charge on each moving particle B. the number of moving charged particles per cubic meter A. the mass of the moving charged particles in the conductor
In the Power Transfer experiment, which of the following is true during the experiment? O a. The power dissipated by the source is constant. O b. The power supply does not dissipate any power. O c. Both the load resistance and the current are variable. O d. The potential difference across the load resistance is constant. e. The current is independent of the load resistance value.
13. You've designed a schematic symbol for a collection of specialty limit switches required for a control circuit. What tool in AutoCAD Electrical can you use to detect errors related to the layers of the drawing and the orientation of the symbol? A. Required Rollout B. Symbol Audit C. Wblock Editor D. Properties 14. What block file format must be available in a drawing to add panel components? A. DWG B. WD PNLM C. MDB D. WD M 15. Two design engineers are discussing AutoCAD Electrical software. Engineer A says that Project Description reference files use a .wdd extension. Engineer B says that the reference files supported by AutoCAD Electrical are ASCII text files with different file extensions. Who is correct? A. Both Engineer A and Engineer B are correct. B. Only Engineer A is correct. C. Only Engineer B is correct. D. Neither Engineer A nor Engineer B is correct.
1.a. An unintentional electrical path that's conducting current from an ungrounded conductor to a normallynoncurrent-carrying metal raceway would be defined as a groundA. conductor.B. fault.C. electrode.D. interrupter. 1.b. It's important for designers and installers to ensure that equipment ground-fault current paths have________, which will facilitate the tripping of the overcurrent protective device.A. low impedanceB. proper labelingC. high impedanceD. an equilibrium
A circuit contains three resistors connected in series across 100 volts; the circuit current is 2 Amperes. Two resistors (R1 and R2) have known values of 5 and 10 ohms,respectively. Determine:a. The resistance of the entire circuit.b. The resistance of the third resistor R3.c. The voltage drop across each resistor
Under what condition is the terminal voltage of a source of potential equal to the electromotive force? a. When internal resistance equals external resistance b. When the internal resistance is parallel to the external resistance c. After one RC time constant d. When the current flows in reverse e. When there is no current flowing