96- give the manufacturing process suitable for the followings parts of the nominated materials part Medical syringe Belt. Engine cover Gear Water pipe line materials Polymer,glass Lather rubber, wool Polymer, metal Metal ceramic, polymer Metal, polymer . J Major process Minor process

Q: Are Sue and Alan engaged? Oh yes, married in June. * they will get they are getting

A: Question. Are Sue and Alan engaged? Oh yes, _____ married in June. Answer. Out of the options given…

Q: 5. A Pitot-static probe is used to measure the speed of an aircraft flying at 3000 m. If the…

A:

Q: Determine the magnitude of force at the pin A and in the cable BC needed to support the 500 N load.…

A: Given data weight =500N Considering FBD of the system Considering vertical forces equlibirium…

Q: Problem 6: The top wall moves with velocity Vtop = 1" and the bottom wall is m S stationary. Inside…

A: VISCOSITY is defined as internal resistance offered by one layer of the fluid to the adjacent layer…

Q: any way the solution set c

A: Lead and aluminum both have FCC crystal structures  Density of solid aluminum= 2.71g/cm3.

Q: The posltion of a particle is r = { (3t° - 2t)i - (4t"2 + t)j + (3ť° - 2)k} m, where t is in…

A: Given data  r = (3t2 - 2t) i - (4t1/2 + t) j + (3t2 - 2) k   To determine the magnitude of the…

Q: If 1 ton of bituminous coal is burned to generate electricity, how many kWh could be produced if the…

A: Dear student,                     There are two different problems that you have posted but…

Q: The posltion of a particle is r = { (3t° - 2t)i - (4t"l2 + t)j + (3t² - 2)k} m, where t is in…

A: To determine the magnitude of velocity and acceleration of the particle.

Q: he several disadvantages as com

A: Answer given below.

Q: Determine the length b of the triangular load and its position a on the beam such that the…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: Water flows from a large tank into a 6" diameter pipe through an entrance condition of a square…

A: Given:Pipe diameter, D2=6 inchRadius of the rounded inlet, r=0.12 inchFind:The head loss reduced at…

Q: A family wishes to buy a 2020 Toyota Camry. The two options the consider are (a) a standard…

A: Given:Economy of SI engine, Vs=34 mpgFixed cost of SI engine, Fs=$18,000Economy of hybrid engine,…

Q: Does this example read true to yourself or is your way the correct way according to an external…

A:

Q: Choose a problem and apply the basic engineering process to solve it.

A:

Q: Explain in detail the Application of Physics (Electricity and Magnetism) in Engineering, especially…

A: The application of physics especially electricity and magnetism part in manufacturing are:-…

Q: Solve it all handwriting please

A: the stresses and select a shaft diameter for the industrial mixing machine. However, I cannot…

Q: the use of machines

A: Belt Length At the point when the head and tail pulley are a similar size: L=(D+d)/2 x 3.1416+2CAt…

Q: Good afternoon!  May I know where is the part of b) 4 mpa. Thank you!

A:

Q: An air hockey table has dimensions as shown in the picture. 0.3m Usually, the air from the table…

A: according to the given data

Q: I am not able to see the answers can you please write it in a paper

A:

Q: 3- Among several engineers thermodynamics are: (a) James Joule. (b) James Watt. (c) Benjamin…

A:

Q: How does science and technology help us?

A: The advancements in science and technology has helped the race of mankind to evolve at a higher…

Q: please, i need to see how did you get to this formula

A: ◆ The purpose of using this formula is to avoid complex calculation and to get the answer in minimum…

Q: please give me some new ideas it has mechanism for junior project in mechanical engineering . please…

A: A mechanism is a device in engineering that converts input forces and movement into the required set…

Q: ) In an unused area of the test facility, lie two internal combustion engines that were brought in…

A: Compression-Ignition Engine (Diesel cycle): - Cut off ratio=V3V2=3.6T3=1400 °C=1673 K,T1=75 °C=348…

Q: Explain the following with appropriate examples (at least 2 examples) 1. Grubler's criterion. 2.…

A: The Grubler's criterion gives the number of degrees of freedom of a mechanism involving links and…

Q: You are required to create a hydraulic device that can transform 20 N of input force and to 5 times…

A:

Q: Excel help if given the distance force and time how am to plot the force-deformation curve and then…

A: To plot a force-deformation curve in Excel from given data (distance, force, and time) and label the…

Q: Exercise 13.18 A Determine the centre of gravity of the bent rod 0.6 m 0.8 m shown. Rod AO is made…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at  45o  with 0.250” leg distance.

Q: Can you give me an example of laying out compound curves, please include explanation for each…

A:

Q: What is the working principle of balancing?

A:

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.