9.21 A smooth, flat plate of length = 6 m and width b = 4 mis placed in water with an upstream velocity of U= 0.5 m/s.Determine the boundary layer thickness and the wall shear stressat the center and the trailing edge of the plate. Assume a laminarboundary layer.9.22 An atmospheric boundary layer is formed when the windblows over the earth's surface. Typically, such velocity profilescan be written as a power law: u=ay, where the constants a andn depend on the roughness of the terrain. As is indicated in Fig.P9.22, typical values are n = 0.40 for urban areas, n = 0.28 forwoodland or suburban areas, and n = 0.16 for flat open country(Ref. 23). (a) If the velocity is 20 ft/s at the bottom of the sail onyour boat (y= 4 ft), what is the velocity at the top of the mast(y 30 ft)? (b) If the average velocity is 10 mph on the tenth4500.28E 300150FIGURE P9.22

Answered: Image /qna-images/answer/89e85da5-3596-4c72-8e65-5a7fe751bb37.jpg

smooth, flat plate of length and wid is placed in water with an upstream velocity of U Determine the boundary layer thickness and the wall at the center and the trailing edge of the plate. Assum boundary layer.

smooth, flat plate of length and wid is placed in water with an upstream velocity of U Determine the boundary layer thickness and the wall at the center and the trailing edge of the plate. Assum boundary layer.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q 20/ The uniform slender bar of length l is placed in the opening of width d at the 30° angle shown. For what range of ld will the bar remain in static equilib- rium? The coefficient of static friction at A and B is Mg = 0.40. 30° A EdH Fig. 20
The cross-sectional area shown is subjected to V-600 kN and M -1000 kN-m. What is the transverse shear stress just below point B? (in MPa) 100 mm 100 mm 100 mm 100 mm 100 mm B 100 mm
Q2) A parallel plate is moving over another plate as shown in the figure below. The liquid viscosity is 5x10°m²/s and its specific gravity is 0.88. Assuming linear velocity distribution in the gap please calculate the power required to pull the upper plate. Please show the directions of the shear stress at the lower and upper plates separately. U = 0.3 m/s d = 0.3 mm
4) A large moveable plate is located between two large plate as shown in the figure. Determine the magnitude and direction of the shearing stresses that act on the fixed walls when the moving plate has a velocity of 4 m/s. Assume that the velocity distribution between the plates is linear Fixed plate 6 mm H- 0.02 N. sim 4 m/s 3 mm A = 0.01 N• sim Fixed plate
Q1: For the two dimensional state of stresses snown in tne rigure, Tina ine normal and shear stresses acting on plane A and show the results in a sketch. All stresses are in kN/m? A 42.5 24 19.6 80 Q2 Shown in Figure 1 is the two-dimensional state of stresses at a certain point within a soil mass. Determir the stresses acting on the horizontal and vertical planes passing through that point and show them in a sketi 65 kNIm? 20 Is kNIm?
A two-storey building structure is shown in Figure 5. The beams are assumed as rigid and the flexural rigidity of the columns is given in the figure. a) determine vibration frequency and mode shape of the structure; b) check the orthogonality condition of the derived mode shape; and c) determine the Rayleigh damping matrix of the system with 5% damping for both modes. M=10000 kg El=10,000 kNm El=10,000 kNm 3m М-20000 kg EI=30,000 kNm EI=30,000 kNm 3.0m Figure 5
1. Boundary layer thickness, displacement thickness and momentum thickness2. Mean velocity profile in outer scaling3. Mean turbulent stresses in outer scaling4. Calculate the shear velocity and plot the mean velocity in inner scaling. Explain how youobtained the shear velocity.5. Turbulence quantities in inner scaling and compare the profiles to a standard boundarylayer profile of the same quantity from literature. Table nomenclature:y – wall normal distance in m, first value denotes the measurement very close to the upperedge of the water flow with a depth of 0.136 mU – streamwise velocity at any y location in m/su’ – streamwise fluctuationsv’ – wall normal fluctuationsOverbar denotes the mean quantity, and the dimensions are in SI units
Q.5 The velocity distribution for flow over a plate is given by U=2y-y² in which u is the velocity in ms¹ at a distance y metres from the plate. Determine the shear stress in Nm-2 at the boundary and at 0.2 m from it. Dynamic viscosity of fluid is 0.9 Ns/m².
9.30 A laminar boundary layer velocity profile is approximated by the two straight-line segments indicated in Fig. P9.30. Use the momentum integral equation to determine the boundary layer thickness, 88(x), and wall shear stress, 7, 7(x). Compare these results with those in Table 9.2. 8/2 2U U 3 FIGURE P9.30
2. The velocity distribution of a viscous liquid flowing over a fixed plate is given as V= 0.68 y - y? for 0sy<0.34 m. "y" is the distance from the plate in meters and the unit of the velocity is m/s. Calculate the shear stress at the plate surface (y=0) and 0.34 m away from the plate (0.9 Ns/m2). Draw the velocity and shear stress profiles. Fixed plate flow
A 750 kN load will fall from a height of 3.2 m. Assume EI = 400 x 10^10 Nmm2 . a) What is the maximum midspan deflection in mm? b) What is the maximum midspan moment in kNm
A thin plate with infinite span is set at a positive angle of attack in a supersonic airstream. The pressure across a supersonic wave generated from the leading edge on the lower surface of the plate is give by linear theory P2 = 1+ 2.8 0 P1 Where P2 and P are the air pressures downstream and upstream of the wave, respectively and the 0 is the angle of attack in radian. Determine the Mach Number