9.12 Water flows past a flat plate that is oriented parallel to the flowwith an upstream velocity of 0.5 m/s. Determine the approximatelocation downstream from the leading edge where the boundary layerbecomes turbulent. What is the boundary layer thickness at thislocation?9.13 A viscous fluid flows past a flat plate such that the boundarylayer thickness at a distance 1.3 m from the leading edge is 12 mm.Determine the boundary layer thickness at distances of 0.20, 2.0, and20 m from the leading edge. Assume laminar flow.

Answered: Image /qna-images/answer/6e0be93b-f1c3-4c6d-b49a-8162151695f4.jpg

0.12 Water flows past a flat plate that is oriented parallel with an upstream velocity of 0.5 m/s. Determine the ap ocation downstream from the leading edge where the bour ecomes turbulent. What is the boundary layer thickn ocation? 2.13 A viscous fluid flows past a flat plate such that the ayer thickness at a distance 1.3 m from the leading edge Determine the boundary layer thickness at distances of 0.2 10 m from the leading edge. Assume laminar flow.

0.12 Water flows past a flat plate that is oriented parallel with an upstream velocity of 0.5 m/s. Determine the ap ocation downstream from the leading edge where the bour ecomes turbulent. What is the boundary layer thickn ocation? 2.13 A viscous fluid flows past a flat plate such that the ayer thickness at a distance 1.3 m from the leading edge Determine the boundary layer thickness at distances of 0.2 10 m from the leading edge. Assume laminar flow.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Similar questions

The uniform velocity ‘U’ of water flowing in a pipe at 70 oF is R ft/s. Figure outthe following(a) the distance at which the transition occurs from a laminar to a turbulentboundary layer and(b) thickness at the point of transition [if the thickness of this initial laminarboundary layer is given by 4.91 (vx/U)^0.5](v = 1.052 X 10-5 ft2/s)
Question 4 Calculate the laminar boundary layer thickness by using Prandtl -Blassin's relation at the middle of a flat plate. The density of the flowing fluid is 600 kg/m3. Velocity of flow is 10 m/sec. and the dynamic viscosity of the fluid is 10 poise. (Length of plate = 4 m)
Problem Air is flowing over a smooth plate with a velocity of 10 m/s. The length of the plate is 1.2 m and width 0.8 m. If laminar boundary layer exists up to a value of R₂ = 2 x 105, find the maximum distance from the leading edge upto which laminar boundary layer exists. Find the maximum thickness of laminar boundary layer if the velocity profile is given by U U Take kinematic viscosity for air = 0.15 stokes.
3) If we compress water by applying 20433.5 Mpa pressure, how much volume change can be observed?. Bulk Module of water is 2178 MPa
3. A cubical block weighing 4.5 N and having a 40 cm edge is allowed to slide down an inclined plane surface making an angle of 30 degrees with the horizontal on which there is a uniform layer of oil 0.005 cm thick. If the expected steady state velocity of the block is 12.5 cm/s, determine the viscosity of the oil (in poise). Also express the kinematic viscosity in stokes if the oil has a mass density of 800 kg/m^3. *
A thin 30-cm x 30-cm flat plate is pulled at A horizontally through a 3.6-mm-thick oil layer sandwiched between two plates, one stationary and the other moving at a constant velocity of 2.2 m/s as shown in the figure. The dynamic viscosity of the oil is 0.027 Pa-s. Assuming the velocity in each oil layer to vary linearly, (a) plot the velocity profile and find the location where the oil velocity is zero, and (b) determine the force that needs to be applied on the plate to maintain this motion Fixed wall h₁ = 1 mm h₂: = 2.6 mm Vw = 2.2 m/s Moving wall Last names with A to M Last names with N to Z A (m/s) 7.6 starting starting 8.9 F
Consider the laminar flow of water over a flat plate of length 1 m. If the boundary layer thickness at a distance of 0.25 m from the leading edge of the plate is 8 mm, the boundary layer thickness (in mm), at a distance of 0.75 m, is
A sound wave is observed to travel through a liquid with a speed of 1550 m/s. The specific gravity of the liquid is 1.5. Determine the bulk modulus for this fluid. EN = N/m²
4.38 Two liquids with different densities and viscosities fill the gap between parallel plates as shown in Fig. P4.38. The bottom plate is fixed; the top plate moves with a speed of 2 ft/s. The ve- locity profile consists of two linear segments as indicated. The fixed control volume ABCD coincides with the system at time 1 = 0. Make a sketch to indicate (a) the system at time t = 0.1 s and (b) the fluid that has entered and exited the control volume in that time period. y| A ID 0.5 ft 0.4 ft -0 ft/s -1.6 ft FIGURE P4.38 2 ft/s B -1.5 ft/s x
3-102 Consider a large cubic ice block floating in seawater. The specific gravities of ice and seawater are 0.92 and 1.025, respectively. If a 25-cm-high portion of the ice block extends above the surface of the water, determine the height of the ice block below the surface. Answer: 2.19 m Sea Cubic ice block 25 cm h
A thin 30-cm x 30-cm flat plate is pulled at A horizontally through a 3.6-mm-thick oil layer sandwiched between two plates, one stationary and the other moving at a constant velocity of 2.2 m/s as shown in the figure. The dvnamic viscosity of the oil is 0.027 Pa's. Assuming the velocity in each oil layer to vary linearly, (a) plot the velocity profile and find the location where the oil velocity is zero and (b) determine the force that needs to be applied on the plate to maintain this motion. Fixed wall h₁ = 1 mm h₂ = 2.6 mm A Moving wall Last names with A to M Vw = A (m/s) starting 2.8 F 2.2 m/s
2. A thin 30-cm x 30-cm flat plate is pulled at A horizontally through a 3.6-mm-thick oil layer sandwiched between two plates, one stationary and the other moving at a constant velocity of 2.2 m/s as shown in the figure. The dynamic viscosity of the oil is 0.027 Pa's. Assuming the velocity in each oil layer to vary linearly, (a) plot the velocity profile and find the location where the oil velocity is zero and (b) determine the force that needs to be applied on the plate to maintain this motion. Fixed wall = 1 mm |h₂ = 2.6 mm Last names with A to M A Moving wall Last names with N to Z Vw = 2.2 m/s W A (m/s) starting 7.6 starting 8.9 F