9. IF BL=57H, C;=1 ,show the content of BL after the ROL BL,1 instruction executes. 10. IF BL=57H, C==1 ,show the content of BL after the RCL BL,1 instruction executes. 11. IF BL=57H, C-=1 ,show the content of BL after the ROR BL,1 instruction executes. 12. IF BL=57H, C-=1 ,show the content of BL after the RCR BL,1 instruction executes

9. IF BL=57H, C;=1 ,show the content of BL after the ROL BL,1 instruction executes. 10. IF BL=57H, C==1 ,show the content of BL after the RCL BL,1 instruction executes. 11. IF BL=57H, C-=1 ,show the content of BL after the ROR BL,1 instruction executes. 12. IF BL=57H, C-=1 ,show the content of BL after the RCR BL,1 instruction executes

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Assume that each instruction starts from these values: AL=A3H, AH=0H, BL=12H AL is negatively signed. 1. MUL BL AX=. 2. IMUL BL .... AX= 2/ 3. DIV BL 2 AX=... 4. IDIV BL / AX=...
For example, suppose an instruction is not accepted and VA page 30 is generated. For the following use cases, a TLB controlled by software might be preferable than one handled by hardware:
Using the diagram, what would be the paths.
How many times the instruction (MUL DX) is executed? MOV CX, OFFFFH. MOV DX, 0458H SSS: MOV AX, 0023H MUL DX INC CX JZ RRR JNCSSS RRR: HLT FFFFH times FFFEH times 1 time 0 time
4. We have the following data for a branching instruction, where T = branch is taken, and N = the bgranch is not taken: TTTTNNNNNNNNNNNTTTTTTTTNNNNNNNNNNTTTT a. what is the success prediction rate for the one bit prediction method? b. what is the success prediction rate for the two bit prediction method? C. compare the two and comment
Give for both the instructions
Consider an instruction ADD AC, A, B which adds the contents of location A and the contents of location B into register AC, and keeps the result in AC (AC AC + A + B). The address of A is stored in adress1 field, and the address of B is stored in adress1 field of the instruction as follows: ADD AC Address1 Address2 Write the sequence of micro-operations required for the bus structure of the following figure to perform ADD AC, A, B instruction. *.**.*.0 Internal CPU bus lines Data lines Address
21-
What happens if an instruction writes to VA page 30 without being approved? A software-managed TLB would be quicker than a hardware-managed TLB in the following situations:
The following instruction is executed. Assume that before execution, register R15 contains 0x18, and the flags are ZF=0, SF=1, and CF=1. Ox indicates hexadecimal; do not include a 0x with your answer. Instruction: CMP R15, 0x21 After execution, register R15 contains (in Hex) and the flags will be ZF= SF= and CF=
3. Suppose M8=x and M9=y. After each instruction has been executed, what is the content of the location indicated in column 3? Fill the contents in the table. Address M1 Content MMR M8 R1 MMR M9 R2 Locations Register 1 Register 2 Accumulator M7 Content М2 M3 ADD R1 R2 М4 МАМ M7 M5 HLT M7
For example, suppose an instruction is not accepted and VA page 30 is generated. For the following use cases, a TLB controlled by software might be preferable than one handled by hardware: