9- Design equation F(A,B,C,D) ={(1,2,5,9,10,11,13,15) using a 8x1 Mux?InputsFABCDA0000 000011 AB=00B0010 1 F=CD + CD'0011 00100 1AB=010101 0F=C'D' + CD04x1MUX0110 0B10111 1FY21000 11001 1 AB=101010 1 F = 1310111100 0AB = 111101 1F =D01In this question, is the solution correct ornot? And if it was a mistake, correct itusing the same solution

Brief description : In the above given question we need to implement the given list of minterms by…

9- Design equation F(A,B,C,D)={(1,2,5,9,10,11,13,15) using a 8x1 Mux? Inputs F ABCD 0000 0 0001 1 AB=00 0010 1 F=CD+CD' B 0011 0 0100 1 AB=01 0101 0 0 4x1 F=C'D' + CD 0110 0 MUX 1 0111 1 Y 2 1000 1 1001 1 AB=10 3 1010 1 F=1 1011 1 1100 0 AB = 11 1101 1 F =D 1110 0 1 In this question, is the solution correct or C D

9- Design equation F(A,B,C,D)={(1,2,5,9,10,11,13,15) using a 8x1 Mux? Inputs F ABCD 0000 0 0001 1 AB=00 0010 1 F=CD+CD' B 0011 0 0100 1 AB=01 0101 0 0 4x1 F=C'D' + CD 0110 0 MUX 1 0111 1 Y 2 1000 1 1001 1 AB=10 3 1010 1 F=1 1011 1 1100 0 AB = 11 1101 1 F =D 1110 0 1 In this question, is the solution correct or C D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 8 160 Which of the po160100555- 870479447 In the DAC unit, the analog level at the A 1601005559870479447 g160100555 B 0870479447 There may be applications that require digital-to-analog conversion but do not need analog-to-digital conversion. 9870479447 1601008 9441 Basically, the process is the reverse of the conversion) changed and in this 160 0555 - 987 9441 The signal produced by this conversion process can basically be 555-987 s respect it is similar то 916 It would not be possible to produce a realistic sine signal with a 4-bit DAC unit. 087047944 to the PWM unit. 1601008 160100555 measured with a DC multimeter. 2555-987047944 g160100555 - 7944 9168
2)Convert 11011010100100012 to hexadecimal. A)895B B)CA11 C)53AC1 D)DA91
Q2 In the circuit as shown below. Determine the (ripple factor) and sketch vp(out) for the filtered bridge rectifier with a load as indicated. 2 : 1 D3 D1 120Vp-p f= 50HZ + Output V1 V2 D2 D4 1uf R1=2k
Scimal value of the value that will occur at the ADC output. (ADC is 12 Question 2 MN is the last two g160100555 - yu digits of In an analog measurement operation set as an external reference, the reference source of the ADC is a voltage source of 5 analog input, write the g160100555-Gu Aumber your student 010055 g160100555 - Yu 9441 20100 g160100555- Y 44 s0100538 g160100555 - Y 944 201005 g160100 2447 .5Volts. In case of 3.5V voltage to the 30100555 -98 9447 30100555 - 987 30100555
5. A 12 bit DAC has a stepsize of 8mV. Determine the full scale output voltage and percentage resolution. Also, find the output voltage for the input of 010101101101?
BkcBZYhc850ZmX4-RzV7i6yWprtMcdra5me-w_Og/formResponse The DAC with inputs and outputs shown in figure below, the fault in the circuit is in note (all the values is in approximate range ) RF R1 200 120k U1 R2 60k R3 741 30k R4 15k - 13.2 mV - 15.6 mV - 29.9 mV -65.6 mV -79.9 mV - 82.2 mV - 96.5 mV R1 O R2 0000 0010 0100 0110 000 1001 1010 1011 1101 1110 III 0000
A 3-bit binary weighted resistor DAC and a 3-bit R-2R ladder DAC have common values of Vref = 5V, R = 1kN, R = 2kN. Compare their output voltages for each of the following binary inputs. What do you observed? Binary Weighted Resistor DAC Resolution Binary input R-2R Ladder DAC Output voltage Resolution Output voltage 000 001 010 011 100 101 110 111
Listen A 12 bit DAC has a lower reference voltage of OV and an upper reference voltage of 3.0V What is the output voltage for a code of Ox74B? Round the answer to 2 decimal places. a) 1.37V Ob) 1.50V c) 1.60V O d) 1.12V
Find this specification of 333 -2SURC/S400 -A8 (LED)
Initially all outputs were RESETE.. Then the input (which is given in the figure) is applied. What is the output value (Q3,Q2,Q1,Q0) after 3 clock signals. MSB Qo Q MSB 1101 D D D. D Output 14 - > CLK D CLK D CLK > CLK FLALEL CLK O A 1101 O B 1011 O 9 1110 O D 0110 O E 0101
A 3-bit ADC with a reference of 10V is used to sample a DC signal. What is the outpout D2.DO for an analog input Vin= 3.349 V Select one: O a. D2.D0 = 100 O b. D2.DO - 101 Oc. D2.D0= 011 O d. D2.D0 = 111 Oe. None of the mentioned.
VI Ru Ri Vz I, Io R2 = 3837.79 O. R3 = 3989.3 Q. %3D R4 = 2898.06 Q. V1 = 4.8 V. V2 = 8.1 V. 11 = 0.0099 A Determine the following: a.) The output current lo %3D