8.74. A plate of aluminum which has become heavily oxidized over a period of time is placed in a large enclosure and exposed to a convection environment with h = 40 W/m2 . °C and T 30°C + 0.5°C. The plate temperature is measured as 86°C +0.7°C. Calculate the effective temperature of the large enclosure and estimate its uncertainty. %3D

8.74. A plate of aluminum which has become heavily oxidized over a period of time is placed in a large enclosure and exposed to a convection environment with h = 40 W/m2 . °C and T 30°C + 0.5°C. The plate temperature is measured as 86°C +0.7°C. Calculate the effective temperature of the large enclosure and estimate its uncertainty. %3D

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.82P: Discuss the modes of heat transfer that determine the equilibrium temperature of the space shuttle...

See similar textbooks

Similar questions

Discuss the modes of heat transfer that determine the equilibrium temperature of the space shuttle Endeavour when it is in orbit. What happens when it reenters the earths atmosphere?
6. a. The heat flux applied to the walls of the biomass combustion furnace is 20 W/m2. The furnace walls have a thickness of 10 mm and a thermal conductivity of 12 W/m.K. If the wall surface temperature is measured to be 50oC on the left and 30oC on the right, prove that conduction heat transfer occurs at a steady state!b. Heating the iron cylinder on the bottom side is done by placing the iron on the hotplate. This iron has a length of 20 cm. The surface temperature of the hotplate is set at 300oC while the top side of the iron is in contact with the still outside air. To reach the desired hotplate temperature, it takes 5 minutes. Then it takes 15 minutes to measure the temperature of the upper side of the iron cylinder at 300oC. Show 3 proofs that heat transfer occurs transiently
Answer this ASAP,thx Furnace walls are lined with 3 layers of firebrick with a thickness of 6 in (k=0.95 Btu/h.ft.°F), insulating brick (k-0.4 Btu/h.ft.°F) and common brick (k=0.8 Btu /h.ft.°F) Firebrick inlet temperature, T₁ = 1800°F, maximum insulating brick temperature, T₂ = 1720°F and T3 = 280°F. 1. Calculate the thickness of the insulating brick layer. 2. If the common brick is 9 in., calculate the exit temperature.
The bottom of a 50mm diameter, 2mm thick metallic induction heater is 120C while its thermal conductivity is 60 W/m-C. The voltage and current flowing into the heater are 220V and 5A, respectively. Find the temperature at the top portion of the pan. Sketch diagram and show pertinent solutions. Box your final answer and express numerical values in 2 decimal places
P34.9 Two parallel metal plates separated by 1 cm are held at 300, and 298 K, respectively. The space between the plates is filled with N2 (or = 0.430 nm² and Cv, m = 5/2 R). Cv.m Determine the heat flux between the two plates in units of W cm².
5. A pipe with an outside diameter of 2.5 inches is insulated with 2 inches layer of asbestos (k = 0.396 Btu- in/hr-ft²-°F), followed by a layer of cork 1.5 inches thick (k = 0.30 Btu-in/hr-ft²-°F). If the temperature at the inner surface of the pipe is 290°F and at the outer surface of the cork is 90°F, calculate the heat loss per 100 ft of insulated pipe. (Btu/hr)
2 kilograms of gas with a molecular weight of 28 is closed and equipped with an electrical resistor. located in a rigid tank. This system has a fixed resistance of 10 amps and a voltage of 12 volts for 10 minutes. is implemented. When thermal equilibrium is reached, it measures that the temperature of the gas rises by 40.3°C. shows. It is estimated that the heat transfer to the environment occurs as 20 W. With the help of the measured data and assuming the ideal gas behavior, the gas's Determine the average value of the specific heat Cp in kJ/(kg K).
Question 5: Z=62 a. An iron sphere of mass (Z + 300)g is kept in a container having boiling water (100 °C). If the temperature of the sphere is 25.5°C, how much heat energy is absorbed by the iron sphere? Consider the specific heat of iron as 452J/kg. b. The wall of an industrial furnace is constructed from (Z + 3) cm thick fireclay brick having a thermal conductivity of 1.7 W/mK. Measurements made during steady-state operation reveal temperatures of 530°C and 375°C at the inner and outer surfaces, respectively. Find the rate of heat loss through a wall which is (Z + 5) cm by (Z + 3) m on a side.
Answer within 10 minutes : The temperature at the inside surface of an oven is 460 oF. The inside wall of the oven is made of brick and is 8 inch thick. The thermal conductivity of the brick is 2.2 Btu/hr.ft2.(oF/ft). The outside of the oven is covered with a 3-inch layer of asbestos as insulation, which has a thermal conductivity of 0.11 Btu/hr.ft2.(oF/ft). If the outer surface of the insulation has a temperature of 100 oF , calculate the amount of heat lost through 2 ft2 of wall area in 3 hours.
Given the illustration and data below. Determine the heat lost per day. T1 = 1000°C T2 T3 = 80°C A = 1 m²2 5 cm 10 сm W k = 0.09 т-к %3D W k = 1.64; т-к
Q.3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂ = 50°C, respectively. If you know that the wall thickness L = 0.2 m, thermal conductivity k = 1.2 W/m.K, and surface area A = 15 m². Determine (a) the variation of temperature within the wall and the value of temperature at x = 0.1 m and (b) the rate of heat conduction through the wall under steady conditions. (10 Pts)
Q.3) The two sides of a large plan wall are maintained at constant temperatures of T₁ = 120°C and T₂ = 50°C, respectively. If you know that the wall thickness L= 0.2 m, thermal conductivity k = 1.2 W/m.K, and surface area A = 15 m². Determine (a) the variation of temperature within the wall and the value of temperature at x = 0.1 m and (b) the rate of heat conduction through the wall under steady conditions.