8. A piston engine operating on the Carnot cycle uses air as the working fluid. At the start of isothermal expansion air is 521 psi & 1100°F. Isothermal Expansion ratio = 1.25. Isentropic Compression ratio = 3.2. The amount of air circulated is 15 Ibm/min. Draw and label the P-V and T-S diagram. Determine the following; a.) Temperature of the sink, °F b.) The Carnot cycle efficiency, in % c.) Power output, Hp

8. A piston engine operating on the Carnot cycle uses air as the working fluid. At the start of isothermal expansion air is 521 psi & 1100°F. Isothermal Expansion ratio = 1.25. Isentropic Compression ratio = 3.2. The amount of air circulated is 15 Ibm/min. Draw and label the P-V and T-S diagram. Determine the following; a.) Temperature of the sink, °F b.) The Carnot cycle efficiency, in % c.) Power output, Hp

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A compression ignition engine operates on a diesel cycle has a compression ratio of 20 and uses air as the working fluid. The air at the beginning of the compression process is at 100 kPa and 30 C. If the maximum temperature of the cycle is 2000 °C. Under cold air standard assumptions at room temperature. Task 1 a. Describe with the aid of diagrams the operational sequence of four stroke compression ignition engines. b. Explain the mechanical efficiency for an ideal diesel cycle of two and four stroke engines c. Explain the relationship between thermal efficiency (n), compression ratio (r), and cut-off ratio (rc).
Instructions: solve problems under the concept of Reheat, Regenerative and Reheat-Regenerative Cycle in Rankine cycles (set the values to 4 decimal places for consistency) Review Questions (M.1) Steam at 10 MPa, 600 °C enters the first-stage turbine of an ideal Rankine cycle with reheat. The steam leaving the reheat section of the steam generator is at 500 °C, and the condenser pressure is 6 kPa. If the quality at the exit of the second stage turbine is 90%, determine a) the mass flow rate of the steam in kg/h and b) thermal efficiency (%) of the cycle c) mass of the cooling water in kg/ h, if the temperature rise in the cooling water is 20 °C.
Plsss answer with complete solution and diagram. Thanks! ❤️ P.s use english system unit.
1. What is the specific enthalpy at the outlet of the turbine and compressor in KJ/Kg 2.what is the power output per unit mass flow rate of air of the turbine . 3.what is the rate of heat input per unit mass flow rate of the air during the heat addition process
A gas turbine cycle with two stage of compression and two stage of expansion, the overall pressure ratio is 9, air enters each stage of compression at 298 K and each stage of turbine at 1200 K. Determine the thermal efficiency of the cycle under the following conditions:- 1- no heat exchanger is used. 2- ideal regenerator is used
In an ideal Rankine cycle, steam is generated at 4.1 MPa and 480 deg. C. The condenser is at 32 deg. C. Determine: a. The cycle thermal efficiency b. For the engine with the same end states, the thermal efficiency and steam rate
A Brayton cycle with an air-powered regenerator has a pressure ratio of 8. The lowest and highest temperatures of the cycle are 310 K and 1150 K. The adiabatic efficiencies of the compressor and turbine are 75% and 82%, respectively, and the efficiency of the regenerator is 65%. Show the cycle in the T-s diagram. Consider the variation of the specific heats with temperature. a) The temperature of the air at the turbine exit, b) Net work of the cycle, c) Calculate the thermal efficiency of the cycle.
What is the dryness fraction at state 6 to 3 d.p.