8. A block (mass m1) lying on a frictionless inclined plane is connected to a mass m2 by a massless cord passing over a pulley. (a) Determine a formula for the acceleration of the system of the two blocks in terms of m1, m2, Theta, and g. 1. (b ) What conditions apply to masses m1, and m2 for the acceleration to be in one direction (say m1 down the plan) or in the opposite direction ?

8. A block (mass m1) lying on a frictionless inclined plane is connected to a mass m2 by a massless cord passing over a pulley. (a) Determine a formula for the acceleration of the system of the two blocks in terms of m1, m2, Theta, and g. 1. (b ) What conditions apply to masses m1, and m2 for the acceleration to be in one direction (say m1 down the plan) or in the opposite direction ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Given: A uniform slender rod is at rest upon a frictionless horizontal surface when a force (F) is applied in the direction shown. Assume that the rod has mass m and length L. A L Horizontal Plane Given that F = 74lb, L = 7.1 ft, mg = 4.6lb, and 0 = 73deg What is the component of acceleration of the mass at point G in the i direction? Answer: Check What is the component of acceleration of the mass at point G in the j direction? Answer: Check What is the component of angular acceleration of the mass in the k direction? (remember your signs) Answer: Check
Derive the equations of motion using Lagrange's equations. (I, =mr? ) THE MOTION IS ON THE HORIZONTAL PLANE (NO GRAVITY) Trailer, mass M Cylinder, k1 mass m k2
The Block with a mass of 4-Kg is hung with a spring. The stiffness constant of the spring K = 10 N/cm. The block is at rest position at point A with a 4-cm stretched of spring. Block is pulled down immediately with a force F=100-N Calculate the velocity of block when it passes point B which is 5-cm away from point A. K. 10 N/cm. 4 kg. VA- O A 5.cm. F = 100-N ---- --- VB = ?
A hanging mass, M1 = 0.5 kg, is attached by a light string that runs over a frictionless pulley to a mass M2 = 1.5 kg that is initially at rest on a frictionless ramp. The ramp is at an angle of θ = 30.0° above the horizontal and the pulley is at the top of the ramp. Find the magnitude and direction of the acceleration of M1. a. 4.905 m/s2 , upward c. 4.905 m/s2 , upward b. 4.805 m/s2 , downward d. 4.805 m/s2 , downward
Prism 1 of mass ml and with angle sits on a horizontal surface On the prism, a bar 2 of mass m2 is positioned. Find the prism's acceleration assuming there is little friction. 2 1
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Korean Bell. A bell-ringer hits a massive bell using a 21-kg cylindrical log. The log is supported by two cords that behave like a rod. He normally uses a 200-N force P, at 60° with respectto the log, to push the log towards the bell. Assuming the two supports have negligible mass, determine the (a) normal and tangential accelerations of the log, and the (b) force developed at each support, at the instant when the cords are vertical and the angular velocity of the log is ω = 6 rad/s, CW. *kindly, include all necessary FBDs and solutions*if necessary, use g=9.81 m/s2
block C mass = 99 kg block D mass = 66kg horizontal force (H) = 555N and is applied at block D. Angle = 32.779 degrees note: Ignore friction. Computations must follow D'Alembert's Principle or else the solution is null and void. And answers should be in Newtons or KiloNewtons 1.) Calculate the Normal Force of Contact between blocks D and C. 2.) Determine the Block D Acceleration 3.) Determine the Block C Acceleration
Consider a square plate at rest in the horizontal plane with mass m, sides of length 2L, and center of mass at point G (located at the center of the square). Two forces are applied to the plate: FA is applied at corner A with some angle o relative to the edge of the plate, and FB is applied at point B parallel with the edge of the plate, as shown. The resulting motion is a pure acceleration (translation) to the right of magnitude a. The plate does not rotate. Determine the magnitude of the force applied at B, ||FB||. (Hint: Use Euler's 2nd Law about an arbitrary point (in this case about point A). FAS 2L 2L F B B a
Motorized moving platform is lifting a car with some acceleration. If the combined weight of the lift platform and car is 2800kg, and the motorized lift weight is 200000kg, determine the maximum acceleration of the platform before tipping occurs. Weight of the platform a=2.1m, b = 4m, c = 4.2m, d = 3m FBD of the lift: Vertical lift platform. center of gravity (car) FBD of the car: a C Too center of gravity (lift)
A 30-kg disk with a radius of 0.7 m is pushed against a spring (k=900N/m). At the instant show where the spring is deformed by 0.2 m, the disk is released from rest. kAx Assume that the disk will roll without sliding after release. The coefficient of non-sliding friction between the floor and the disk is 0.3. 1. Which of the following kinematic relationships relating the acceleration of the mass center of the disk a, and its angular acceleration a is correct? a. a, = 0.7a b. 1.4a, = a c. 0.7a, = a d. a,=1.4 ma ma, 2. Given the force diagram of the package, which of the following is the most ideally constructed diagram? lect U www B W(0.7) +0.2kg+ma(0.7)² 17 3. Which of the following equations summing of moments about A is correct and can be used to solve for the angular acceleration of the disk? 8 W(0.7)+0.2k(0.7) = Iga+ma(0.7)² 17 8 C W (0.7) +0.2k(0.7) = fg+ma(0.7) 17 15 0. 17W (0.7) +02k(0.7)-Ig+ma(0.7) 4. What is the total acceleration of the mass center of the disk? 5. What is the…
cord 30° P= 34 N Cylinder: r= (25 mm 4 kg m = A uniform cylinder is pasitioned on a 30° slope, and a cord that is wrapped around it leads of in the uphill direction, as shown. A force P (parallel to the slage) is everted on the end of the cord. Assuming that the cylinder tolls without sliding along the slope, find: (a) the acceleration à of the mass center (may and divec) Gatic) (b) the friction force F exerted on the cylinder at the point of contact. A
Need help in 15 minutes. ASAP. A 75-kg block is attached to a cable. The cable is then attached to a rotating assembly with a mass moment of inertia of 18 kg-m^2. The bearing friction applied at the rotating assembly equivalent to a couple of 45 N-m CCW. The block's downward speed is initially at 2 m/s. What is the total work done by the system after the rotating assembly has rotated 1.5 radians CW? What is the speed of the 75-kg block after the rotating assembly rotated 1.5 rad CW?