8. A 30.0 mH inductor with a resistance of 4 2 is connected to a 12.0 V battery. Find the curren after 12.5 ms?
Q: d) Determine the total inductance for the connection shown in Figure 5.1 below. 2mH oor 14 6mH von…
A: Given data, Circuit diagram is given as,
Q: 12 Q www. 24 www 36 V + R 36 Ω www N 1
A: Given : I4=1A
Q: Q/A single-phase transformer with a capacity of 100 kVA and a voltage of 2000/400 and the equivalent…
A: The transformer is a static device that helps to step up or down the voltage or current level by…
Q: 2. Find V, in the network in Fig. P3.50 using nodal analysis. (1+ 1 kΩ ; 12 V 4₂ www 1k02 2 mA 21₂…
A: Since you have asked multiple questions in a single request, we will be answering only the first…
Q: An analog voltage in the range 0 to 10.8 V is divided in 16 equal intervals for conversion to 4-bit…
A: It is given that: Vmax=10.8 VVmin=0 VL=16
Q: RG Rin Ti = 10 ΜΩ VDD= + 15 V Ro = 10 ΚΩ www Μ R, = 10 ΚΩ
A:
Q: 1. (a) Design a single-pole low-pass filter with a gain of 10 in the passband and a 3dB frequency of…
A: Low-pass filter A low-pass filter is a circuit that allows low-frequency signals to pass easily…
Q: Find the attenuation constant for the medium whose properties are given below. f = 10(kHz) fly = 7 o…
A:
Q: 3. Find the ratio of starting to full-load current for a 7-46 kW, 400 V. 3-phase induction motor…
A: Given data:- Output Power Pout=7.46 kW Line Voltage VL=400 V Full-Load Efficiency ηFL=0.87 Full load…
Q: A B C D UN2 UIN2 Y
A:
Q: b) A 208-V three-phase power system consists of an ideal 208-V Y- connected three-phase generator…
A: Given data Phase voltage, Van=120∠0° Vbn=120∠-120° Vcn=120∠-240° Impedance of the load Zϕ=12+j9 We…
Q: 3. The output of a shunt generator is 66A at 593 V. armature and field resistances are 0.05930 and…
A:
Q: A battery with an emf of 13.7 V has a terminal voltage of 13.3 V when the current is 2.46 A. HINT…
A: Given data, A battery is having, EMF E=13.7 V. Terminal voltage V=13.3 V. Current I=2.46 A.
Q: Determine whether the following systems are time varying or invariant, linear or non-linear systems:…
A:
Q: One DC separately excited motor with rated data of PN-3kW, n =1500r/min, UN-110V, n=0.91, Ra=0.892.…
A:
Q: For the given circuit, the value of capacitor is in mF. So that the system will be critically damped…
A: Given- Circuit is given, Resistance R=40 ohm, Inductance = 4 H, To Find- The value of the capacitor…
Q: An analog voltage in the range 0 to 10.8 V is divided in 16 equal intervals for conversion to 4-bit…
A: Given : Analog voltage, Vp-p=10.8V n=4
Q: A 220V do motor developing 25 hp (18.65 kW) runs at a speed of 1000 r/min.. Calculate the torque in…
A: In this question We need to determine the torque of the motor. We know Torque = Output power /w= Po…
Q: 1.If you compare the ohmmeter readings with the colors reading for the given resistance. could you…
A: Ohmmeter It is a type of measurement device which is easily portable and used to measure electrical…
Q: a) Rin(base) b) Rin c) Av d)current gain e)power gain..
A: The required parameters can be calculated by using the DC and AC analysis of the amplifier circuit.
Q: For the circuit shown to the right, after the switch is closed, the transient current i (in A) is…
A: Given data, Current it=21+e-0.4t Given circuit,
Q: solve Vc(s) using KCL at V1 and Vc(s). The answer I've been getting is (9030+900s)/(15s^2 +150s…
A: It is given that:
Q: 2. A low-pass filter is to have a cutoff frequency of 10 kHz and is to have a gain at 20 kHz, which…
A: Consider a low-pass filter with a cutoff frequency of 10 kHz and a gain of 20 kHz.
Q: Question 4. The Fourier transform of ƒ(t) is F(w) = 5e-6jw wj 3 2 + Using the Convolution Theorem,…
A:
Q: Let two random signals Y(t)=sin(t+0), 0². (a) (b) is uniformly distributed on X(t) = cos(t+0) [-π,π]…
A: Given: Two random processes, X(t)=cos(t+θ), and Y(t)=sin(t+θ), where θ is uniformly distributed…
Q: The value of Z in Figure, which is most appropriate to cause parallel resonance at 500 Hz, is
A: It is given that: f=500 Hz
Q: Find the Inverse Laplace Transform of the following functions 1 1) F(s)=- 2) F(s) = S 3) F(s) == 5)…
A: Given: (1) F(s)=1s2+s,(2) F(s)=1s3+4s,(3)F(s)=1s(s-as+a),(4) F(s)=8s4-4s2,(5) F(s)=8s4-2s3,(6)…
Q: Discussion: 1. What is the differences between a normal diode and a zener diode?
A: We need to tell about difference between two diodes .
Q: = + x te tf te De R1 R2 R3 R4 Volts 10k 2.7k 3.3k 6k T V 26V Using the following elements, we can…
A: Given: In this question, the given details are, Here, the given elements, And then the elements are…
Q: Find the reflection coefficient for each of the following sets of scattering = variables: (a) a =…
A: Reflection Coefficient It is the percentage of the energy that gets reflected back towards the…
Q: A 2300 V 400 Hp 60 Hz eight-pole Y connected synchronous motor has a rated factor of 0.85 leading.…
A:
Q: A resistance wire strain gauge with a gauge factor of 2 is bonded to a steel structural member…
A: Given- Gauge factor G=2, Stress =100 MN/m2, E=200 GN/m2, To Find- The % change in the value of the…
Q: Find the Inverse Laplace Transform of the following functions
A:
Q: Please Draw the Circuit and Solve. 1)The non inverted active low pass filter has impedance resistor,…
A: The circuit of active loss pass filter can be designed as
Q: C i) What is the difference between a proximity sensor and a limit switch? ii) State 3 types of…
A:
Q: 3) A 555 timer is connected in the stable mode as shown in the figure below. Determine the frequency…
A: Given data A 555 timer is shown in the figure which is in stable mode. We need to find the…
Q: The inductance of a long solenoid of length 1000 mm wound uniformly with 3000 turns on a cylindrical…
A: Given- Length of the solenoid, l = 1000 mm Number of turns, N = 3000 Diameter, d = 60 mm Radius, r =…
Q: Calculate the capacitance of a single phase 50 Hz overhead line 40 km long consisting of two…
A:
Q: Find the attenuation constant for the medium whose properties are given below. 01) 0,616 02) 9,105…
A:
Q: A B с 2 7432 3 1 7400 In the circuit from above, A=1, B=0, C=0, and the output X=0. X Considering…
A: Given: The logic circuit is, Inputs are A=1, B=0, C=0. Output is X=0.
Q: 9. In a circuit with a 12 volt supply and 4 2 resistance, the power consumed is 10. What is the unit…
A: 9. Given data, Supply voltage V = 12 V. Resistance R=4 Ω. Power consumed by resistor is given by,…
Q: A 240 V, 4-pole wave wound DC series motor has 600 conductors on its armature; it has armature and…
A: Given- 240 V, 4-pole wave wound DC series motor, Number of conductors Z=600, Number of poles P=4,…
Q: A three phase 50 Hz fully transposed line has conductors equilaterally spaced at 3 metres. The…
A:
Q: Describe the voltage across and the current through the inductor combination in both charging and…
A: Given: the circuit diagram consists dc source, resistor, and capacitor I) when the source is…
Q: It is dependent source problem do it correct otherwise will give dislike
A: It is given that:
Q: Q4, (a) Consider the circuit on the right. The resistor values are 22, and the inductance is 1 H.…
A: Given:
Q: find The m and Draw The output signal of AmpsB Vc (t) = 8 cos2πxist Ac pm(t)
A: Given: vct=8cos2π×105t and Ac=8 Volts.
Q: Find the Thevenin Equivalent for the following circuit by finding: • v open circuit; • i short…
A: Given data: circuit diagram is given as:
Q: 16.40 An 8-bit A/D converter has a reference voltage of 10 V. Find (a) the analog input…
A: The analog signal can be converted into digital signal by using the ADC converter. The conversion…
Q: QUESTIONS A long vertical wire is partially placed in a uniform magnetic field B-53 mT. The B-field…
A:
Step by step
Solved in 3 steps
- You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
- You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
- Which of the following is not a requirement for an electric circuit? a. a source b. a path c. a load d. a signal lightYou are a journeyman electrician working in an industrial plant. Your task is to connect an inductor to a 480-V, 60-Hz line. To determine the proper conductor and fuse size for this installation, you need to know the amount of current the inductor will draw from the line. The nameplate on the inductor indicates that it has an inductance of 0.1 H. An ohmmeter reveals that it has a wire resistance of 10 . How much current should this inductor draw when connected to the line?Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
- A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a current flow of 24 amperes. The circuit current must be reduced to 16 amperes by connecting a second capacitor in series with the first. What is the value of the existing capacitor? What value capacitor should be connected in series with the original capacitor to limit the circuit current to 16 amperes?What is the unit of measurement for the strength of a capacitor? microamp microtorque microfarad microwattAn inductor has a current flow of 3 amperes when connected to a 240-volt, 60-Hz power line. The inductor has a wire resistance of 15 . What is the Q of the inductor?