76. A 200-kVA, 2300/460 V, 60-Hz two-winding transformer is to be used as an autotransformer to step-up the voltage of 2300 V to 2760 V. Determine kVA rating of autotransformer. A. 200 C. 1200 B. 800 D. 1500

76. A 200-kVA, 2300/460 V, 60-Hz two-winding transformer is to be used as an autotransformer to step-up the voltage of 2300 V to 2760 V. Determine kVA rating of autotransformer. A. 200 C. 1200 B. 800 D. 1500

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter4: Symbols

Section: Chapter Questions

Problem 7SQ: The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d....

See similar textbooks

Related questions

Q: Find the inverse Laplace transform of the following function: 6. X(s) = s2 + 6s + 8

A: Given, Xs=6s2+6s+8

Q: write about: Typical Band Stop Filter Configuration

A: Typical Band Stop Filter Configuration Since two filters are connected in parallel so input signal…

Q: In a PWM, what should be the duty cycle to get a voltage output of 4.5 V

A: It is given that: Output Voltage=Vout=4.5 V

Q: For the circuit shown in figure: m R= 40 L=1H V, (t) Vour(t) C= 0.2 F

A: The given circuit diagram is shown below:

Q: Assume the eference is the ottom node in the cuit below. rite the noda equations, solve them, and…

A: Circuit diagram is given as,

Q: For the periodic function: f(æ) ={ :-1 0<=<1 1 -1<a <0 %3D x -1 0<x <1 Determine: 1. Is it Odd,…

A: We are authorized to answer three sub-parts at a time, since you have not mentioned which part you…

Q: In the ideal transformer circuit of Fig. 13.38, find V, and the complex power supplied by the…

Q: Describe the following x86 assembly instructions with their syntax/example: i) lea imul iii) idiv

A: Note: As per Bartleby guidelines, we are supposed to provide solution of first question only as…

Q: no load current of a transformer

Q: For the figure system 5 sis + 2) I+ as Find the characteristic equation and bring it to the Evans…

Q: 21. The average value of the output voltage of a half wave rectifier is greater than the average…

A: The average value of output voltage of half wave rectifier is, VoHWR=Vmπaverage And, the average…

Q: find the current passing through the surface Z=1, 0<X<1, O<Y<1 if H= Y^2*X ax-3*Z^3*y az 1.2 A 1.3A…

Q: Salve the diff equ.

Q: Q: Suppose you have the following modulated signal: +2 -2 If the value of the symbol rate is 2Kbps,…

Q: Example-9: Consider a Delta modulator system designed to operate at 4 times the Nyquist rate for a…

Q: State two advantage of microwave communication over satellite communication.

A: With the use of high modulation, selective receivers, (QAM, PSK, SSB etc.) and spread spectrum…

Q: Design an FM system that achieves an SNR at the receiver equal to 40 dB and requires the minimum…

A: Given:SNR at the receiver=40dBBandwidth=120 kHzmessage bandwidth=10 kHzaverage to peak power ration…

Q: R1 R3 Vs Vout R2 Vin Figure 2.2 (c) What is the small-signal output voltage, vout, for the circuit…

A: We need to find out output voltage for given circuit.

Q: A 10-hp,4 pole,25Hz,3-phase induction motor is taking 9100 watts from the line.Core loss is 290…

Q: I1 12 V 20 13* a 60 12 8 V

Q: 1) The working parts of a cathode ray tube (CRT) are enclosed in a high vacuum glass envelope to…

A: Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: Write an Arduino code to control two LEDs using two push buttons, given the bellow setup: LED 1 is…

A: The LED pins should be used as output pins and Button pins should be used as Input pin in program.

Q: For the figure system 5 sis + 2) 1+ as Find the characteristic equation and bring it to the Evans…

A: Given:

Q: Difference between three phase and single phase induction motor... Don't copy from other websites…

Q: Encuentre la tonrión VclH) para t> 0 del crcuito a la 125 F 18 Función U(t) Ve • C- T2u14) A 24 mm…

A: The solution is given below

Q: For the input transducer Resolvers, write/ sketch: Description Basic construction/…

Q: By using N-Mos, plot the following equation with the transistor y = AB + CBD?

Q: 1. Add 5 ohms in every element in the network and solve for Zah j6 2 -j9 2 a j6 2 -j9 2 j6 2 -j9 2…

A: In this question, We need to calculate the equivalent impedance across the terminal a and b. If 5…

Q: R1 10 uF Ipss=

A: Solution- AC EQUIVALENT- R1& R2 are in parallel & Rs & RL are parallel, Small signal…

Q: To replace 1500 Q resistor in a radio by any number of 1000 Q resistor, which way they can be…

Q: 1) Estimate the shape of magnitude response of H(z). Take b=0.5. 2) What is the type of system…

A: NOTE- As per the rules we can answer only 3 sub-parts, please post the remaining sub-parts as the…

Q: Which of the following quantities is increase in a step-down transformer? O Current O Voltage O…

A: As per the definition, the transformer is a device that can convert one voltage level to another…

Q: H. W2: - Determine the z-transform, including the ROC, pole-zero- plot, for sequence x(n) = (;) u(n)…

Q: Design a common emitter amplifier for a Vout of+-6.3V. Vcc is set to 9V. At x=1, Av=12.6 V/V and the…

A: We need to design a common emitter amplifier for a Vout of ±6.3V and Av=12.6 V/V. Also, Rout must…

Q: 2- In the logic circuit shown below, what is the minimum R, that the inverter can drive without…

Q: 3. The voltage v across a device and the current / through it are (1) = 5 cos 21 V, i(1) = 10(1–…

Q: a system or circuit conductor (one that carries current), that is intentially grounded is referred…

A: The grounding is done to provide path for excess flow of current in order to prevent the devices or…

Q: write about: Band Stop Filter Characteristics 200 words do not write in handwritten and DO NOT…

A: Band pass filter :There are pass filter band and one band - stop in the Band Stop filter. This…

Q: -What is PAM? And What are the different types of sampling? -What is the purpose of the sample and…

A: Sampling: The process of measuring the instantaneous values of continuous time signal in a discrete…

Q: In air, a lossless transmission line of length 50 cm with 10µH/m, C = 40PF/m is operated at 25 MHz.…

A: Given a lossless transmission line having, Length, l = 50 cm Inductance, L=10 μHm Capacitance, C=40…

Q: find the current passing through the surface Z=1, O<X<1, O<Y<1 if H= Y^2*X * ax-3*Z^3*y az 1.2 A O…

A: We need to find out current for given magnetic field intensity.

Q: Determine the PIV, turns ratio, the maximum output voltage as well draw the output wave form of the…

Q: A. What values of B correspond to a = 0.970, 0.993, 0.250? (b) What values of a correspond to B= 40,…

A: Given, (a) α=0.970, 0.993, 0.250 β=? (b) β=40, 200, 3 α=?

Q: A certain transistor has an Ic 20 mA and an Ig 200 µA. Determine the Bpc. %3D

A: Given, A certain transistor has Collector current, Ic=20 mA Base current, IB=200 μA

Q: 4. Find the periodicity of the following signal. x(t)=cos((2rn/7)t)sin((3t/5)t) a) 30 b) 7 c) 35 d)…

Q: for the system y(n)=x(n)-2.n.x(n+1) , which of the following statements are true and which are false…

A: In this question we will find system linearity, stability ,causal etc...

Q: A current of 2A in the ay direction is in a filament parallel to the ay direction and passing…

A: It is given that: Filament:I=2A ay passing through 8,-10,0infinite sheet:K=20 az Am at Y=-2

Q: To replace 1500 Q resistor in a radio by any number of 1000 Q resistor, which way they can be…

A: To replace 1500 ohm resistor we need 3 unit of 1000 ohm resistor first we will connect first two…

Q: voltage of 7.2 V across the load. The input voltage is constant at 12V and the vary from 12 to 100…

A: The solution is given below

Q: 8 kl 5 kfl 500 N 6 kn3 7 kn3 7 kll 800 n 1200 Nl 300 N 18 V 27 V 200 N (a) (b) 50 N 90 N 80 N 10 N…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
A 100/S00 V. 1 KVA, 50 Hz transformer was put through open and short-circuit tests to find its internal parameters. The test conditions and derived parameters are as follows Open circut test: The high voltage side terminals were open. The low voltäge side was connected to 10020ª, 50 Hz supply. The low voltage side current was measured as 50245º MA. Short-circuit test The high voltage side terminals were short-circuited. The low voltage side was connected to a variable voltage supply (50 Hz). A full load current of 102-30° A was achieved when the variable voltage supply was at 820° V. The transformer was then put to operation by connecting a load of 400230° 2 to the high voltage side (secondary) while applying a primary voltage of 10020º V. Calculate the primary current (the current drawn from the power supply).
In the circuit in Figure 2, the capacitor connected to the a-b terminals of the transformer anda circuit consisting of resistance is defined as a load circuit. a)Find the average power spent by the load circuit? b) How much of the average power calculated in a) by the resistance in the load circuit and how muchspent by the capacitor? Comment on the results obtained?
74. The eddy-current loss in a 6.9 kV, 50 Hz transformer is 220 W. What will be the eddy-current loss of this transformer if it is to be connected across a 6.6 kV, 60 Hz source? A. 201 W C. 234 W B. 224 W D. 212 W
66 A single-phase transformer is rated 440/220 V, 5.0 kVA. When the low-tension side is short- circuited and 35 V is applied to the high-tension side, rated current flows in the windings and the power input is 100 W. Find the resistance and reactance of the high- and low-tension windings if the power loss and ratio of reactance to resistance is the same in both windings.
Following are the results of a test carried out on a 230/600 V single phase, 7.5 kVA transformer. O.C. Test : 230 V, 1.2 A, 280 W, on L.V side S.C. Test : LV winding is shorted. 26 V, 11A, 155 W, H.V. Both the full load efficiency and full load regulation of the transformer on the side are 0.8 lagging p.f Search on.
63. A 15-kVA, 60 Hz, 240/120 V transformer has a core loss of 350 W. The full load copper loss is 650 W. Determine the primary load current at maximum efficiency. a. 42.4 A b. 44.2 A c. 45. 8 A d. 40. 2 A
30-kVA, 2200/220-V, 50-Hz distribution transformer is tested for efficiencyand regulation as follows :O.C. test( Low voltage side ) : 220 V 4.2 A, 148 W S.C. test ( Low voltage side ) : 86 V 10.5 A, 360 W 1-The working current and resistance component of no-load are.........amper , .........ohm * 2-Efficiency at full-load and half the full-load at 0.8 p.f. lagging current. * 3-Equivalent resistance referred to primary & referred to secondary..........ohm , ..........ohm * 4-Regulation of transformer at 0.5 p.f. lagging current * 5-Equivalent reactance referred to primary & referred to secondary..........ohm , ..........ohm * 6-The magnetizing current and reactance component of no-load are.........amper , .........ohm *
The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined. The open-circuit test and the short- circuit test were performed on the primary side of the transformer, and the following data were taken: Open-circuit test (on primary) Short-circuit test (on primary) 8000 V V= 489 V I0.214 A 2.5 A P= 400 W P= 240 W Find the impedances of the approximate equivalent circuit referred to the primary side, and sketch the circuit.
SOLVE AND SHOW THE DIAGRAM: A 200-kVA, 3-phase, 50-Hz transformer has a voltage ratio (line voltages) of 33/11-kV and is delta/star connected. The resistances per phase are: high voltage 30 ohms , low voltage 0.88 ohms and the iron loss is 2000 W. Calculate the maximum efficiency and the efficiency at half load, both at 0.75 power factor lagging
Flag this question for future reference What is the test that can be conducted in the laboratory to understand the transformer impedance drops are dependent on the load current with a variation in the secondary voltage? O a. Direct Load Test O b. Open Circuit Test OC. Voltage Ratio Test O d. Polarity Test
10 A three-phase transformer is given. The number of turns of the high voltage winding is N1=850 and the number of turns of the low voltage winding is N2=34. The high voltage winding is energized with V1= 10 kV rms line-to-line and V2= 400 V rms line-to-line has been taken from the low voltage winding. What is the connection of the low voltage winding if the high voltage winding is Y-connected? Εισαγάγετε την απάντησή σας