75KN 75KN 60KN 15KN/m 50KN 1.5m 2.5m 2.5m 1.0m 1.0m 75mmX200mm LOAD DIAGRAM FOR PROBLEM 2 DRAW THE SHEAR AND MOMENT DIAGRAM. AND CALCULATE THE MAXIMUM FLEXURAL STRESS OF THET-BEAM. (REFER TO LOAD DIAGRAM FOR PROBLEM 2.

Q: Compare and contrast the uses of T-square and setsquares.

A: T-square: It is a technical instrument that is used for drawing purposes.  It is mainly used by…

Q: Determine external as well as total indeterminacy

A: Given data : Number of External support reaction (R)=2+2=4Number of member (m)=6Number  of joint…

Q: The ∑ F proceeding in the couple is?

A: Brief concept- Couple- It is a pair of equal and opposite parallel forces. These two forces do not…

Q: Determine the centroid of the shaded area shown, which is bounded bythe X axis and the parabola y? =…

A:

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: entify the outfall entify the peaks entify the valleys

A: Watershed: A watershed depicts an area of land that contains a typical arrangement of streams and…

Q: For the given structures, determine the degree of indeterminacy. 6. T 6

A: The given beam has three support conditions. The Left end is a Fixed support.(3 reactions)…

Q: Use the unit load method to calculate the vertical displacements at the quarter and mid-span points…

A: The given figure is shown below:

Q: Determine centroid Y-bar with respect to X-axis, Centroid g w rupect to x-axis 8" 6"

A:

Q: 4- Which statement is true about the precedence of lines? A. a hidden line has precedence over a…

A:

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: Determine the XT and YT(using both a and b) a. Using the Top Most, Left Most Reference Line b. Using…

A:

Q: but I nee

A: Draw the figure Consider a differential element of size dy

Q: What does it mean if a beam is “non-compact

A: Beam is defined as a structural horizontal element which is used for resisting loads which are…

Q: What is the Ix and Iy of the cross-section in mm4

A: Given: Required : Ix and Iy of the cross-section in mm4

Q: 9- The Scale The scale of a drawing is... Lo = X Lo = Lo= e= If e 1: Full size representation. e 1:…

A:

Q: Write the types of structures in detail.

A: The type of structure to be constructed for a purpose depends upon the use of structure, load on…

Q: Find the centroid of square from bottom of X axis having dimension 8 mm *8 mm

A:

Q: Permutations and Combinations. How many different permutations can be made of the letters in the…

A: Here we have 8 words in the term infinity.  Among 8,  two words are repeating in nature, that is I…

Q: show the (c)

A:

Q: What is beam

A: The amount by which a beam deflects upon its cross-section, bending moment and shear force. For…

Q: For the given structures, determine the degree of indeterminacy. 1. ♫

A: This question is related to the Structure analysis

Q: y 25 45 55 25 65 80 I 55 165

A: Divide the given area into five parts as shown in part 1 of the question…

Q: Part A What is the ratio scale for the equivalent scale of 1 in. = 80 ft? Express your answer using…

A: 1 ft =12 inch given 80 ft =12*80=960in Ratio scale=112×80=1:960

Q: can you explain how to do this in cad. using the details below. Can you like specify the dimensions…

A: Given data,

Q: 30 10 30 10 15 20 15 10

A: Line command of autocad is used  We can use either absolute coordinate method or relative coordinate…

Q: Please find the centroid x and y bar, and Ixx for the following shapes. Show all work with neat…

A: Approach to solving the question: Detailed explanation:Examples: Key references:

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: How do I get the support forces

A: The x and y are the vertical and horizontal distances: x=12cos60=6 fty=6sin60=5.196 ft

Q: 112 тm К30 тm ->- 30 тm -+30 тm ->-30 mт -> Рart a) Determine the moment of inertia of the shaded…

A:

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Q: 100 N 100 N 100 100 150 250

A:

Q: Solve thee following problem step by step so I can understand in neat hand writing.

A:

Q: Y

A:

Q: Explain why wx = 2/3(9-x)

A: Given:Required:To explain loading intensity for 6<x<9

Q: 12 13 12 13 14 10 Which tools that can be used to :4 draw the following shape in .AutoCAD R5 R10 R12…

A: To draw the given shape we will require the following command necessarily :- Dimension, line or…