70 Мра y

Q: Determine Iy. 50 mm 50 mm 300 mm 50 mm y -200 mm an -X We Problem 4

A:

Q: On the attached drawing 11A005< what is dimension "G"

A:

Q: Eonsider a osow botshat stagitupward fom the grund y-0) at ime t=0 wih niha elocy, -4 – Take g= 98-…

A:

Q: Using the diagram, determine the maximum diameter for DIA B.

A:

Q: orthographic view (software drawn)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Help in filling table: Material Yield Strength (MPa) Elastic Modulus-E (GPa) Poisson’s ratio…

A:

Q: 01/ Give the dimensions for the hole and shaft for the 12 mm electric motor sleeve bearing (pump);

A: Given:Basic size given for motor sleeve bearing=12 mm

Q: Find the volume described by 0srs 5,0seS T/3, Os O S 2M O a. 125T/3 O b. 251T/3 Oc. 225T/3 Od.…

A: Answer: The volume is 125π/3 . Option (a) is correct.

Q: 2. Indicate the subscripts of stress components in the following cases. Use the given coordinate…

A:

Q: =o7 Cm) findSmax. tor Figure 0,7 Cm) fin mox. tor tigure tigure. 225 mm J0omm

A: Given Data The force acting in the downward direction is: F=400 N The height of the weld is: h=0.7…

Q: 22 R 50 -38 24 10 125 41 20 Drill 48 27 -20.5 -

A:

Q: The Taylor's tool life component is 0.3 and constant is 120 for a cutting tool A and 0.5 and 30 for…

A: Given:nA=0.3CA=120nB=0.5CB=30

Q: Die Ntef d CW ad d 107 30T 167 327

A:

Q: Determine O gn torques 6)7 mo

A:

Q: how 79x10^3 get? or where did the 79x10^3 came from?

A: G = shear modulus of the hollow shaft

Q: 3. If gage A reads -20 kPa, determine the elevations of points L, N, Q and 9. 2 El. 65.00t E Air El.…

A:

Q: 181-2,4,0)m A0, 0-6) m Dl0,0, -3 )m w •10 KN ト

A: From the free body diagram given, write the tensions in the cables in cartesian vector form by using…

Q: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 180 KN,…

A: Given : The shear force in this section is The diagram is,

Q: Q3. Design (draw) Inspection gauges for inner diameter of holes and outer diameter of shafts.…

A: Given: Shaft and hole tolerances To Find: Go and No go gauges

Q: Build the following part and report the volume in units cubed. A = 48 B = 51

A:

Q: Figure 1 shows an element ith stresses. Angle 1 Tyx Tyx Figure 1 Point C)- x-direction stress…

A: The three basic equations to determine the stress at various cross-sections are:…

Q: 200 MPa 100 MPa 300 MPa

A:

Q: The shaft Sexerts three force components on the die D. What is the value of 0y in degrees for F2?

A: From the figure: F→1=400 i^ -------- (1)F→2=300×cos 60 i^+A j^ +300×cos 60 k^F→2=150 i^+A j^ +150 k^…

Q: The planetary gear system of automobile. Consider that the crown R rotates as shown clockwise at 750…

A: Given: The gear train is shown below:

Q: M-(!zy.2z– ly.y) + M,(1;.z– lzy.y) Iz. ly – Izy² Мy Pr Formüller; Pr ož - G,0, + o3 < oỷ, Jort =' Iz…

A: Given,

Q: Given D 2KN ← 1m P 2 To Determine 0-3 1m (1-7 one • Diameters of the bars is 1mm e 3 3KN Youngs…

A: Consider elements connecting nodes 1 and 2 as Element-I and element connecting nodes 2 and 3 as…

Q: how would this look like if written?

A: The feature control frame is required to describe the condition and tolerances of the geometric…

Q: Prove that & Y2² 26 for fig.3.

A: Given a vertical prismatic bar of length LThe objective is to prove

Q: For Ta pered pipe shown below, what is a as diameter of the pipe at

A:

Q: B A

A: Given that , m =3 kg t=0.35 s r=4 sin3θ

Q: ។ 2 KN G lom 10KN-M B 6m 8m IKN ях find torque about AB

A: Given DataP=2kNPo=1kNM=10kNm

Q: 250cm+10m

A: Given Data : 250cm+10m

Q: 500 kN.m T KN. m/ m В C 2 m 3 m 5 m Q/Find the value of T (kN. m/m) So that the value of angle of…

A: Given Data Angle of twist at D is zero At A is fixed support so the angle of twist at A is zero…

Q: 5. Use superposition to find the deflection of the free end of the cantilever shown below: w lb/ft 2…

A:

Q: strbes a flet ghke as shown. The wuté Ieaves the noeele at lomls watr from from - statiny nozte the…

A: From Newton's second law of motion - Fjet=- FplateFjet=mvinitial-mvfinal= ρAv2-0 Because final…

Q: Petanmined the magnitude. and direction ot farce (PIR the Resullant of P camdc120NLis to be all6ON)…

A:

Q: Q/Find the value of T (kN. m/m) So that the value of angle of twist at D equal to zero.

A: The elemental angle of twist for the shaft CD can be expressed as, On integrating the above…

Q: Part A A curve of radius 68 m is banked for a design speed of 95 km/h. If the coefficient of static…

A:

Q: The 2-1b block is released from rest at A slides down along the smooth cylindrical surface. The…

A:

Q: 12 Find maX. W=? if of530Mpa Ś GoMpa い Joomm 2m An 30 そaん 500

A: Stress When body is subjected to any load then body resist that load and the resistance is called as…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.