please help 34. Determine the rebar that needs to be ordered to con-struct the continuous footing shown in Figures 5-26 and 5-27. The rebar is to be lapped 18 inches. 16'-0"2 x 4 WALLWITH 7/16" OSB5/8"X 10" ANCHORBOLT @ 32" O.C.8"# 4 REBAR @ 12"O.C. BOTH WAYS22'-0"8'-0"#5 DOWELS @ 12"O.C. ALTERNATINGDIRECTIONS13'-0"2 EACH #4 REBARTOP AND BOTTOM3 EACH #4CONT. REBAR-1'-0"28'-0"12'-0"2'-0"Figure 5-26 Footing PlanFigure 5-27 Wall Section

Show the footing plan as in Figure (5-26) Show the footing plan as in Figure (5-27) Show the…

Answered: 7. The rebar is to be lapped 18 inches.

Engineering

Civil Engineering

7. The rebar is to be lapped 18 inches.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A3 mx 3 m square spread footing is to support a 350 mm x 350 mm column carrying a dead load of 750 kN and live load of 500 kN. For concrete f'c is 21 MPa and for steel, fy is 415 MPa. Use NSCP 2001 provisions. Determine the effective depth considering punching shear. A 300 mm 350 mm 400 mm 450 mm B.
1) Design a rectangular footing for an 16” square corner Column with PDL = 280 kips and PLL = 180 Kips. Make the length of the long side about 1.5 the width of the short side. Fy = 60 ksi F’o= 4000 psi for both, column and footing. Assume the base of the footing is 4'-6" below grade and the depth of the footing is 26". The soil weight is 100 PCF. (Normal weight concrete, No epoxy coating, The Column is reinforced with eight #8 bars.) Need to design for load transfer from the Column to the foating. Need to Show the development length for the dowels. Need to design the bars for footing at both directions. Need to check if the bars fit the footing based on the development legth. Need to show two-way footing Spacing diagram.
A square column with side dimension of 70 mm rests on top of a timber footing. It is determined that the column carries an axial load of 752 kN. If the punching strength of concrete is 14.69 MPa, determine the minimum thickness (mm) of the footing. Hiiiiiii need helppp thank u so much urgenttt
ASAP PLS I GIVE UPVOTE If the square footing has an 800mm edge with a 300mm thickness, and that the 200mm x 200mm column has a 1.1m height from the top of the footing up to the finished ground line are both constructed, how much gravel (in m3) should be exactly used for a class B concrete mixture for the footing and the column (up to the finished ground line level).
Determine the appropriate size of steel bars needed to confirm the development length requirements, the footing has a dimension of 2.0m x 2.0mx 0.8m. The column Section is 350mm x 350 mm Use a minimum protection of steel equal to 75 mm. fy use fc' = 20.7 mpa and fy= 415 mpa. using NSCP 2015.
3. Calculate the total load on a 4'x4'x1' spread footing that is buried 3' below, and a hot tub is located directly above the spread footing and the footing column is l'x1'. Assume the hot tub is full and no one is in the tub. Use some or all of the following data to calculate the total compressive load on the soil directly underneath the footing: a. DL - 12,000 lbs and b. LL-8,000 lbs c. 400 gallon hot tub (empty hot tub weighs 200 lbs) d. Soil weight 120 PCF e. Concrete weight 150 PCF
Square column size 16" 280 kips, PLL = 180 kips L = 1.5B, fy = 60 ksi, f'c = 4000 psi fa 4 ksf, Footing base = 4'-6" Df PDL find 26", soil weight = 100 pcf, Reinforcement - #8 bars 1) Design for load transfer 2) Development length for the dowels 3) Design bars for footing at both directions 4) Bars fit the footing based on development length 5) Two way footing spacing diagram. 4'-6" 26 B VỈ L Ildi [ld₂ Dowel Configuration B 1.5
C9-1. The concrete footing A was poured when this oolumn was put in place. Later the rest of the foundation stab was poured. Can you explain why the 45° cracks occured at cach corner? Can you think of a better design that would avoid such cracks?
Design a RC square footing by Ultimate Strength ACI Column dimensions: 14''x14'' LL= 100 k DL = 71 k qall= 4 ksf f'c = 3 ksi fy = 60 ksi
Design round column footing for 18 in diameter that supports loads of PD = 240 k and PL = 140 k. The bottom of the footing is 6 foot below final grade, reinforced concrete weight is 150 lb/ft3 and the soil weighs 100 lb/ft3 the allowable soil pressure is 5 ksf. The concrete strength is 4,000 psi and the steel is Grade 60. 2
4. A 2.10m x 2.10m footing carries concentrically a square column 0.40m x 0.40m. Design data: Column factored loads: DL = 570KN = 460KN %3D Concrete cover to the centroid of footing reinforcement = 110mm Concrete f'c - 21MPA Steel fy= 415MPA %3D %3D Allowable stresses at ultimate loads: For diagonal tension or two-way action shear = 1.52MPA For wide-beam shear 0.78MPA Maximum steel ratio for moment = 0.016 a. What is the minimum thickness (mm) of footing required for punching shear? b. Determine the minimum thickness (mm) of footing required for wide beam shear. Determine the minimum thickness (mm) of footing required for maximum moment. C.
5 P Question 1 of 8 Determine the number of 6meters - 12mm. steel bars required if there are 10 footings with a general dimensions of 1.50 x 1.50 meters. Show your solution. 1,50 m -1.35 m.- -7.5 cm 1.50 m. 7.5 cm 12 mm steel barn