7. Relate the mass transfer coefficient to film thickness of liquid.

Q: Regarding amorphous plastics, explain why they tend to have higher tensile strength when deformed…

A: Amorphous plastics have no specific order and pattern in their molecular structure. Thus, the…

Q: Define the two types of stress waves ?

A: The two types of stress waves are to be defined.

Q: Flow diagram for absorption

A: Absorption is a separation operation in which the solute from gas mixture is absorbed with the help…

Q: 3 Briefly describe the drilling problems related to drilling fluid rheological property.

A: In fluid mechanics, rheology is the type of study of the flow of matter, matter could be in the form…

Q: For heat transfer, the surface resistance was characterized by a convective heat transfer…

A: For convective heat transfer the heat transfer quotient h is given by:

Q: Density and viscosity fatty acid at 40 degree celcius

A: Various researches and studies have been conducted continuously to calculate density and viscosity…

Q: construct the step of gravimetric analysis of chloride ions in sample of edible salt

A: Gravimetric analysis is a technique that is widely used in the analytical chemistry, that involves:…

Q: A 2 mm diameter glass tube is inserted into an open glass of water (contact angle between the tube…

A: Diameter of glass tube =  2 mmContact angle,  = 0

Q: Make a comparison between thermoplastics and thermosetting polymers(a) on the basis of mechanical…

A: A resin that is solid at room temperature but becomes plastic and soft upon heating is a…

Q: A cylindrical rock sample has a porosity of 14%. The dimensions of the core are 13 cm in length and…

A: Given that, Porosity = 14% Length L = 13 cm Diameter D = 6 cm It is required to calculate the pore…

Q: Calculate the volume of an HCP unit cell in terms of cell edge (a) and height (c).

A:

Q: Cone has top and bottom diameters of 10 and 20 cm and a height of 10 cm. Calculate the shape factor…

A:

Q: Explain why: a) A metallic couple with an unfavourable area ratio (small anode/large cathode)…

A: The given subparts need to be explained.

Q: How do microfiltration and ultrafiltration differ from reverse osmosis with respect to pore size,…

A: Reverse Osmosis (RO) is a phenomenon in which pressure higher than the osmotic pressure on the feed…

Q: Determine the Cunningham Correction Factor for the following particles at 400K and standard pressure…

A:

Q: Temporary hardness can be removed by:

A: The hardness of the water is of two types’ permanent hardness and temporary hardness. The temporary…

Q: In the laboratory experiment "Plate and Frame Filter Press" 1. How is concentration related to the…

A: Introduction  Rate of filtration depends on the area of the filter cloth, the viscosity of the…

Q: In the Energy and Specific Heat lab, how should the aluminum can be stabilized over the heat source?…

A:

Q: Calculate the following: Thermal conductivity of brass Calculated quantities Value Difference in…

A: Hi, thank you for posting the question. According to our guidelines, we are allowed to answer only…

Q: Viscosity varies with temperature according to which of the graphs below?

A: How does viscosity vary with temperature?

Q: Determine the terminal settling velocity of a coal particle of size 400 micron in water at 20 oC by…

A: We need to find settling velocity of coal particle water and then we need to compare it with…

Q: 5. Physical properties of the formation crude oil includes volume coefficient and viscosity.

A: The physical properties of crude oil vary according to its composition, the relative abundance of…

Q: The outermost shell of an atom is called as the shell.

A: In a chemical element, an atom is the smallest particle of matter. An atom consists of a central…

Q: i. percentage recirculation of air ii. Heat Load

A:

Q: graph is different from given data

A: Here the graph is not between mole fraction.

Q: 2. How is phase diagram of water different from most other materials show with sketches. What is its…

A: In a phase diagram; there are certain important terms which should be explained first. Different…

Q: C; Draw the temperature distribution long the insulated tip fin.

A: Fins are used in heat transfer to increase the surface area of a heat exchanger, thereby increasing…

Q: 10. What type of corrosion occurs in multiphase alloys'? a. Crevice b. Pitting c. Intergranular d.…

A: Crevice corrosion is a localized form of corrosion that occurs in narrow, confined spaces between…

Q: Give an example of a hybrid system that involves recycle.

A: An example of a hybrid system that involves recycle is to be mentioned.

Q: It refers to the vapor that is brought back to the column for better separation.   a Distillate…

A: In distillation we have key component as feed, distillate,residue,reflux and boilup.

Q: 6. Which ratio of cathode to anode accelerates galvanic corrosion? a. Larger cathode to smaller…

A: In general, the rate of corrosion is significantly impacted by the relative sizes of the cathodic…

Q: Calculate the porosity of the core

A: Given data: The density of the oil = 0.85 g/cc Weight of dry sample in air = 42.4 g Weight of the…

Q: Which of the following is not correct statement? O a. Matrix is the major load carrier in…

A: To choose the option that is not correct about composites/Al alloys

Q: 27.) An extra plane would be inserted inside the crystal in a/an a) Edge dislocation b) Screw…

A: In the crystal lattice structure there are different defects are present in the lattice structure.…

Q: Determine the following for each item: 1. Equivalent surface diameter 2. Equivalent volume diameter…

A: (1) Equivalent surface diameter is defined as the diameter of the sphere having equal surface area…

Q: Question 16 Match the below definitions Ductility Hardness Case Hardening A. measure of a material's…

A:

Q: Using a flow chart, show how a lubricant oil with high viscosity index can be manufactured from…

A: In petroleum industries, Crude oil is a type of fossil fuel that is a naturally occurring petroleum…

Q: Define glass transition temperature in polymeric materials and name two parameters ineach case that…

A: The glass transition temperature, often denoted by Tg, is a critical physical property of polymeric…