7. For an unknown reason, an adventurous man with a height of 1.95m is holding an open cylindrical container 0.3m in diameter and 0.8m high partially filled with water and is rotated about its vertical axis at a speed of 240rpm. What would be the depth of water in the container if the cylindrical container is brought to rest so that no water will be spilled out? At what speed would it be rotated so that the pressure at the center of the bottom of the tank is zero?

7. For an unknown reason, an adventurous man with a height of 1.95m is holding an open cylindrical container 0.3m in diameter and 0.8m high partially filled with water and is rotated about its vertical axis at a speed of 240rpm. What would be the depth of water in the container if the cylindrical container is brought to rest so that no water will be spilled out? At what speed would it be rotated so that the pressure at the center of the bottom of the tank is zero?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

an open cylindrical tank 0.3m in diameter and 0.8 high is partially filled with water to a certain depth. when rotated about the vertical axis at 240rpm, water just reach the rim of the tank. at what speed in rpm would the tank be rotated if 1.4 liters of water is spilled out?
7. For an unknown reason, an adventurous man with a height of 1.95m is holding an open cylindrical container 0.3m in diameter and 0.8m high partially filled with water and is rotated about its vertical axis at a speed of 240rpm. What would be the depth of water in the container if the cylindrical container is brought to rest so that no water will be spilled out? At what speed would it be rotated so that the pressure at the center of the bottom of the tank is zero?
Q8) You are designing a system for moving aluminum cylinders from the ground to a loading dock. You use a sturdy wooden ramp that is 2.00 m long and inclined at 37.0 degrees above the horizontal. Each cylinder is fitted with a light, frictionless yoke through its center, and a light (but strong) rope is attached to the yoke. Each cylinder is uniform and has mass 420 kg and radius 0.300 m. The cylinders are pulled up the ramp by applying a constant force F to the free end of the rope. F* is parallel to the surface of the ramp and exerts no torque on the cylinder. The coefficient of static friction between the ramp surface and the cylinder is 0.120. a) What is the largest magnitude F° can have so that the cylinder still rolls without slipping as it moves up the ramp? b) If the cylinder starts from rest at the bottom of the ramp and rolls without slipping as it moves up the ramp, what is the shortest time it can take the cylinder to reach the top of the ramp?
Q3: The space between two large flat and parallel walls 25 mm apart is filled with a liquid of absolute viscosity 0.7 Pa.sec. Within this space a thin flat plate 25 cm x 25 cm is towed at a velocity of 0.15 m/s at a distance of 6 mm from one wall, the plate and its movement being parallel to the walls. Determine the force exertem by the liquid on the plate. Stationary plate 6 mm 19 mm 0.15 m/s Stationary plate
:A (19L) cylindrical container with a bottom area of (775cm²) is filled with glycerin and rests on the floor: A. determine the fluid container when the acceleration of (0.9m/sec²). B. what resultant force dose the container exerts on the floor of the elevator during this acceleration? c. what will the angle between static and accelerated case if it also decelerated in horizontal direction (0.9m/sec) Answer with sketch pressure at the bottom of the container has an upward has
6.29 An open rectangular tank of dimensions 4m x 3m x 2m contains water to a height of 1.6m. It is then accelerated along the longer side. What is the maximum acceleration possible without spilling the water? If this acceleration is then increased by 10%, what amount of water will be spilt off? (a) 1.472 m/s? and 0.48m3 (b) 1.962m/s? and 0.48m3 (c) 1.472 m/s? and 0.52m3 (d) 1.962 m/s? and 0.52 m3
20 A lawn sprinkler consists of a rotating runner with two nozzles. The nozzles are oriented at right angles to the runner. The diameter of the runner is 20 mm; the diameter of the sprinkler nozzles is 10 mm. Water is supplied by the attached hose (not shown) at a rate of 14 m³/h. What single force must be placed on one side of the runner at a distance of 100 mm from the center of rotation in order to stop the sprinkler from rotating? 300 mm (A) 12 N (B) 50 N (C) 75 N (D) 290 N 10 mm diameter nozzle center of rotation 300 mm
40 - A cylindrical tank with a diameter of 15 cm and a height of 40 cm was filled with water to a height of 25 cm. If the tank is rotated around the vertical axis of symmetry at a constant speed of 20 rad/s, what will be the difference in water height between the edge and the middle of the tank? a) 15cm B) 11.5cm NS) 9.5cm D) 5.4cm TO) 7.2cm
Why does the concept of inertia pressure become invalid in the case of "instantaneous" closure of a valve in a pipeline?
Given the parabola 3x2 + 40y – 4800 = 0. (a) What is the area bounded by the parabola and the x-axis? (b) What is the moment of inertia, about the X-axis, of the area bounded by the parabola and the X-axis? (c) What is the radius of gyration, about the area bounded by the parabola and the X-axis?6. Determine the reactions at A and B on the Fink truss shown in the figure. Members CD and FG are respectively perpendicular to AE and BE at their midpoints.
5. The coefficient of static friction between the 75-lb box and the inclined surface is 0.1O. The coefficient of static friction between the rope and the fixed cylinder is 0.05. Determine the force the woman must exert on the rope to cause the box to start moving up the inclined surface. What is the minimum force the woman must exert on the rope to hold the box in equilibrium on the inclined surface? 45 20 30
An open cylindrical. tank 0.3m in diameter and 0.8m high is partially filled with water to a certain depth. When rotated about the vertical axis at 240 rpm, water just reach the rim of the tank. At what speed in rpm would the tank be rotated if 1.4 liters of water is spilled out?