7. As shows in the picture, two circular rods have the same diameter, left rod made by steel, right rod made by aluminum, the ratio of shear modulus of two material is 1:3, the deformation of the curved arm at end of the two circular rod is not considered. Request: What proportion of force F will be allocated to the left and right two poles? St Al

7. As shows in the picture, two circular rods have the same diameter, left rod made by steel, right rod made by aluminum, the ratio of shear modulus of two material is 1:3, the deformation of the curved arm at end of the two circular rod is not considered. Request: What proportion of force F will be allocated to the left and right two poles? St Al

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Help me urgent Two forces are applied ti the bar shown in the figure. Determine the normal and shearing stresses at point A, B and C?
I need help with this exercise from my homework. I have no idea about how to solve it. I need an step by step solving and explanation, please.
1. Express the tension force as shown in vector form if the magnitude of T = 200 kips 20 ft A 35 ft 7 ft T B 6 ft
150 mm 60 mn 300 nm 000 m 50 mm 5 m B 25 kNm 5 m 10 KN A beam is created by nailing 3 planks together with 2 rows of nails as shown above. The beam exhibits a pin support at A and is suspended by a cable at B. A concentrated load of 10 kN is applied at the free end while a moment of 25 kNm is applied at location B. a) Determine the second moment of area (I) of the cross-section b) Draw the free body diagram, shear force diagram, and bending moment diagram of the beam c) For the maximum shear force on your SFD, determine the maximum and minimum shear stresses at the interface between the horizontal and vertical planks d) For the maximum shear force on your SFD, Determine the shear stress at the neutral axis
50 kN A 200 mm B 350 mm a a 60 mm 200 mm - change the length of segment BC from 350 mm to 312 mm 50 mm 20 mm 20 mm D 20 mm 50 kN Provide the internal normal force diagram for the figure above with the following modifications:
strength of materials
The lower ends of the three bars in the figure are the same level before the rigid homogeneous W=100 kN block is attached. The properties of the bars are shown in the table. The temperature of the bars is then increased by 80°C. The block is assumed to remain horizontal after all deformations have occured. a.) Which of the following most nearly gives the temperature rise to cause all of the applied loads to be supported by the steel rods? b.) Which of the following most nearly gives the stress developed in the bronze bar? c.) Which of the following most nearly gives the stress developed in the steel bar? 下上F Bronze Length, L Area, A Modulus elasticity, E Coefficient of 11.7x10C linear Steel 1.00 m 500m2 of 200 GPa 1.60 m 900 m 83 GPa Bronze Steel Steel 18x104 C A B expansion, a
If the unit mass of steel is 7850 kg/m3 and E = 200 x 103 MN/m?, find the total elongation of the rod given a steel rod having a cross-sectional area of 200 mm? and a length of 120 m is suspended vertically from one end. It supports a tensile load of 18 kN at the lower end. a. 52.45 mm b. 56.77 mm Oc. 53.44 mm O d. 59.68 mm
The cantilever beam shown has a rectangular cross section with dimensions b = 25 mm and h = 100 mm, and is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a as shown. The beam is made of steel with E = 200 GPa and v= 1/3. Two strain gages are placed at point C, which is also at midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle ß= 60°. The measured strains are &a= 125 µɛ, &b = -375 με. Determine: a) The force P in kN [Ans. to check: P = 125 kN] b) The angle a in degrees. B b←
Flexure stress *Please answer in complete solution and draw the shear and moment diagram, Solve the Area moment of inertia*
1.) 600 lb Determine: 900 lb - The resultant force (R) - The angle 0 between the R and the x-axis 40 35°