7. A particle of mass m is projected vertically downward from a great height with speed 3k in a medium whose resistance to motion is mkv, where v is the speed at time t and k is a constant. The speed doubles after time T when the particle has fallen a distance X. Show that (i) AT = In 2. (ii) In2

Q: Introduction a. Write an introduction in 100 words about temperature and instruments used to measure…

A: Temperature is defined as "the degree of hotness or coldness". The most common temperature measuring…

Q: nterdisciplinary research takes time to have an impact. What is your opinion for this  statement?…

A: Interdisciplinary research

Q: A 4.8 m long from fixed point, 0.5 m wide and assumed a thickness of 30 mm throughout a springboard…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Using the element sectioned at plane b-b and the rotated coordinate system shown, determine the…

A:

Q: True and False (correct the false) 1. In USM, tool tips must have high resistance and fatigue…

A: As per given question we have choose true / false

Q: A new fuel for combustion was found to have the following composition: carbon 71.6%, hydrogen 4.8%,…

A:

Q: 4. Consider a situation similar to that in Experiment 2. Given the following distances traveled…

A: In the question, it is asked about average velocity. Average velocity can be calculated the total…

Q: B: Materials engineer has analytical skills as well as writing and problem-solving skills. Write the…

A: Dear student,                     According to expert guidelines I am allowed to answer only one…

Q: Drilling and Completion Engineering II An exploration well is to be drilled to a total depth of…

A:

Q: Does this example read true to yourself or is your way the correct way according to an external…

A:

Q: three: Three commonly used tests to measure the hardness related properties of materials are:…

A: Hardness is basically resistance offer by material to plastic deformation.

Q: What indices do we use to evaluate the control quality?

A: There are many indices in quality control which are important to evaluate the quality as well as…

Q: SUBJECT COURSE: ERGONOMICS REQUIRED: CONCLUSION AND RECOMMENDATION FOR THE FOLLOWING SCENARIO:…

A: Paragraph 1: (based on the given scenario and details) Based on the results of the stroop test…

Q: Statics of Rigid Bodies Content Covered: - Method of Sections Direction: Create 1 problem based…

A: A simple truss is acted upon by two vertical forces acting at B and D, as shown. Compute to the…

Q: The question and data are in pictures. Please answer properly with each steps and explanation. Best…

A: To determine if Column 1 will remain stable if the water tank is placed directly above it, we need…

Q: 1. Given that the length of the sample is 90 mm and the diameter of it is 7 mm. i. Draw the stress…

A: Write the expression of stress. Write the expression of strain. Draw the given table and calculate…

Q: An air hockey table has dimensions as shown in the picture. 0.3m Usually, the air from the table…

A: according to the given data

Q: Q1) Define the following: 1) The stress & the strain 2) Mechanical stress and mechanical strain 3)…

A: Define the Following The stress and the strain Yield strength Tensile Strength Modulus of elasticity…

Q: In the context of our teaching, which one of the below statements is mostly correct about in…

A: Component design, sometimes known as atomic design (though we prefer "Component design" at…

Q: Method of Sections Direction: Create two problems based on the topic "Method of Sections" and then…

A: As per Bartleby rule one question can be solved in one post so I have constructed one problem using…

Q: I need answers to questions 13, 14, and 15 pertaining to the print provided. Note: A tutor keeps…

A: 13.Calculate the maximum material condition for the largest cylindrical part feature.

Q: Check the incorrect statements. a) As the thickness of the specimen increases, the fracture…

A:

Q: There are two samples, A and B, ere tested by Rockwell hardness test. Sample A is tested in B scale,…

A: HRB means the Hardness Rockwell B scale HRB means the Hardness Rockwell F scale

Q: please give me some new ideas it has mechanism for junior project in mechanical engineering . please…

A: A mechanism is a device in engineering that converts input forces and movement into the required set…

Q: Don’t use ai

A: Step 1: a) Penetrant testing, Magnetic particle testing can be used. Compared to Other NDT methods,…

Q: 1. Identify the different hazards shown in the image. 2. List down the different hazards that you…

A: MACHINE SHOP & THEORY Identified all hazardous on picture

Q: I need answers for problems 13, 14, and 15 pertaining to the print provided.   NOTE: If you refuse…

A: 13.A characteristic of a system which may cause failure or defects if not in line with quality…

Q: Explain the following with appropriate examples (at least 2 examples) 1. Grubler's criterion. 2.…

A: The Grubler's criterion gives the number of degrees of freedom of a mechanism involving links and…

Q: A materials engineer wants to understand the relationship between the strength of plastic cases and…

A: Explanatory Variable is a factor or parameter that has been changed in an experiment by a researcher…

Q: In a large printing operation, an employee using a clamp forklift truck that was transporting two…

A: This is a problem related to industrial safety. Some preventive measures should be taken to avoid…

Q: Excel help if given the distance force and time how am to plot the force-deformation curve and then…

A: To plot a force-deformation curve in Excel from given data (distance, force, and time) and label the…

Q: You are tasked to check the safety factors for the bolt designs for the connection shown with an…

A: Find outSafety Factor for the Bolt DesignCalculate the required torque to bring the bolts to the…

Q: The local planetarium has just closed for its renovation and improvement. As an interior designer,…

A: Overview: The mobile chandelier for the planetarium is designed to embody the majesty and beauty of…

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at  45o  with 0.250” leg distance.

Q: The efficiency for a steel specimen immersed in a phosphating tank is the weight of the phosphate…

A:

Q: There are two types of scales in aerial photographs, mention and explain them briefly

A: There are two types of scale in aerial photographs: i) large scale photograph ii) small scale…

Q: Content Covered: - Method of Joints Direction: Create two problems based on the topic "Method…

A: The method of joints is a process used to solve for the unknown forces acting on any members of a…

Q: The question and data are in pictures. Please answer properly with each steps and explanation. Best…

A: When Column 3 of the warehouse moves downwards by 10 cm due to ground subsidence, it will…

Q: P. F- b 30 mm 50 30 mm mm Solution workout of this question with proper FBD has to be submitted in…

A: Data given-  F = 17.4 N   b = 0.071 m

Q: Using free handed sketching or rulers & compass to create the necessary number of views of…

A: To draw the number of views  by free hand sketch/ by rulers.

Q: What is the major drawback of the Merit index? Select one: O a. The merit index can consider only…

A:

Layout

The layout is a way of organizing the elements, products, and raw materials in a design. The layout is the representation of information in a structural, logical, descriptive, coherent form.The layout is a mapping of various equipment arrangements, workstations, machinery, plants, and more. It secures the continuous movement of a product quantity along with the quality.